[linux-dvb] Twinhan experimental branch

[Thomas Knauer]

Hi,

manu at kromtek.com (Manu Abraham) writes:

>> Kernel is 2.6.11-rc2, because later kernels crash the system when
>> the bttv module is loaded.
>> 
>> bttv: Bt8xx card found (1).
>> ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 19 (level, low) -> IRQ 19
>> bttv1: Bt878 (rev 17) at 0000:01:0a.0, irq: 19, latency: 64, mmio: 0xf8001000
>> bttv1: subsystem: 00a0:bcf8 (UNKNOWN)
>> please mail id, board name and the correct card= insmod option to kraxel at bytesex
>> .org

>I think that one has a new PCI ID, It has a silicon tuner.. ? can you do 
>an lspci -vv and post the PCI ID ?
>Some blown EEPROM's also give wrong PCI ID though..


here's the output "lspci -vv":

0000:01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capt
ure (rev 11)
        Subsystem: Unknown device 00a0:bcf8
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
- <MAbort- >SERR- <PERR-
        Latency: 64 (4000ns min, 10000ns max)
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at f8001000 (32-bit, prefetchable)
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (r
ev 11)
        Subsystem: Unknown device 00a0:bcf8
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
- <MAbort- >SERR- <PERR-
        Latency: 64 (1000ns min, 63750ns max)
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at f8000000 (32-bit, prefetchable)
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

>This looks like a new version of the VP-1030A.. The 1032A is not out in 
>the market though.. ? Can you verify what VP-10XXX it is , such that it 
>can be confirmed ?

The card was bought approximately half a year ago. I'll check this on
Monday, because the server's located at the office.

Regards,
Thomas