[linux-dvb] Twinhan experimental branch

[Jake]

Johannes Stezenbach wrote:

>Helmut Auer wrote:
>  
>
>>I just tried to install my twinhan 1025 as described in README.bt8xx with 
>>cvs from 21.03. but modprobe bttv hangs up the system with kernel 2.6.11
>>    
>>
>I heard three similar reports now, but I'm quite sure it worked for me
>with 2.6.11 (will re-try later).
>  
>
I have this problem for some time with any kernel after 2.6.11-rc3. I'm 
using 2.6.10 right now and it is working fine.

>What's the last line of output from the boot messages?
>  
>
Here are the last line from syslog using 2.6.11.4:

    |Linux video capture interface: v1.00
    bttv: driver version 0.9.15 loaded
    bttv: using 8 buffers with 2080k (520 pages) each for capture
    bttv: Bt8xx card found (0).
    ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
    bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 10, latency: 32, mmio:
    0xe7800000
    bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem
    ID is 1822:0001
    bttv0: using: Twinhan DST + clones [card=113,autodetected]
    bttv0: gpio: en=00000000, out=00000000 in=00f5ffff [init]
    |

And for comparation, here is the output from 2.6.10 on the same system 
(2.6.10 is work fine):

    |Linux video capture interface: v1.00
    bttv: driver version 0.9.15 loaded
    bttv: using 8 buffers with 2080k (520 pages) each for capture
    bttv: Bt8xx card found (0).
    ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
    bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 10, latency: 32, mmio:
    0xe7800000
    bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem
    ID is 1822:0001
    bttv0: using: Twinhan DST + clones [card=113,autodetected]
    bttv0: gpio: en=00000000, out=00000000 in=00f5ffff [init]
    bttv0: using tuner=4
    bttv0: add subdevice "dvb0"
    bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 10, latency: 32, memory:
    0xe7000000
    DVB: registering new adapter (bttv0).
    dst_check_ci: recognize DST-03T
    DST type : satellite
    DST type flags : 0x2 ts204 0x4 symdiv
    DVB: registering frontend 0 (DST DVB-S)...
    |

>Specifically, does it crash when loading bttv or dvb-bt8xx?
>  
>
The system just freeze when loading bttv driver. I was able to capture 
this line from syslog because I have a dedicated system for logging.

>And, more important, does the problem still exist in 2.6.12-rc1-bk3?
>  
>
I have tested and the problems is still in 2.6.12-rc1-bk3.
I have also tried to move my DVB board to different systems and I see 
same hang when loading bttv. I have tried P3 and P4 systems with SiS, 
VIA and Intel chipsets.

Thanks,
Jake
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20050331/1dd1f068/attachment.htm