SV: [linux-dvb] TwinhanDTV Ter-CI + Linux
Anton Berggren
anton at toprunstudio.com
Wed Nov 23 20:15:24 CET 2005
-----Ursprungligt meddelande-----
Från: Anton Berggren [mailto:anton at toprunstudio.com]
Skickat: den 23 november 2005 17:56
Till: 'Martin Ereth'
Ämne: SV: [linux-dvb] TwinhanDTV Ter-CI + Linux
Hi again!
Thanks for the reply i have been waiting the whole day :D
im glad for every suggestions that i can get.
My card is this one.
http://www.twinhan.com/product_terrestrial_4.asp
so it is not a USB-device.
i did this...
"modprobe -v bttv i2c_hw=1 card=0x71"
"modprobe -v dvb-bt8xx"
"modprobe -v dst dst_type=1"
lsmod look like this.
Module Size Used by
dvb_bt8xx 14468 0
nxt6000 8324 1 dvb_bt8xx
mt352 6916 1 dvb_bt8xx
sp887x 8708 1 dvb_bt8xx
dst_ca 18048 1 dvb_bt8xx
dst 25604 2 dvb_bt8xx,dst_ca
bt878 10808 2 dvb_bt8xx,dst
dvb_core 84648 2 dvb_bt8xx,dst_ca
cx24110 9092 1 dvb_bt8xx
or51211 10500 1 dvb_bt8xx
tuner 40360 0
bttv 164048 2 dvb_bt8xx,bt878
video_buf 22660 1 bttv
v4l2_common 6016 1 bttv
btcx_risc 5128 1 bttv
tveeprom 13968 1 bttv
videodev 10112 1 bttv
snd_mpu401 6728 0
snd_mpu401_uart 8320 1 snd_mpu401
snd_rawmidi 26784 1 snd_mpu401_uart
snd_seq_device 8972 1 snd_rawmidi
snd_intel8x0 34912 4
snd_ac97_codec 96124 1 snd_intel8x0
snd_ac97_bus 2432 1 snd_ac97_codec
snd_pcm_oss 53536 1
snd_mixer_oss 19840 2 snd_pcm_oss
snd_pcm 94472 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 26372 1 snd_pcm
snd 58852 14
snd_mpu401,snd_mpu401_uart,snd_rawmidi,snd_seq_device,snd_intel8x0,snd_ac97_
codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10848 3 snd
snd_page_alloc 11016 2 snd_intel8x0,snd_pcm
i2c_nforce2 6912 0
my "/var/log/syslog" look like this after loading modules.
Nov 23 17:22:58 localhost kernel: Linux video capture interface: v1.00
Nov 23 17:22:58 localhost kernel: bttv: driver version 0.9.16 loaded
Nov 23 17:22:58 localhost kernel: bttv: using 8 buffers with 2080k (520
pages) each for capture
Nov 23 17:22:58 localhost kernel: bttv: Bt8xx card found (0).
Nov 23 17:22:58 localhost kernel: ACPI: PCI Interrupt 0000:01:0a.0[A] ->
Link [APC1] -> GSI 16 (level, high) -> IRQ 21
Nov 23 17:22:58 localhost kernel: bttv0: Bt878 (rev 17) at 0000:01:0a.0,
irq: 21, latency: 32, mmio: 0xc0000000
Nov 23 17:22:58 localhost kernel: bttv0: detected: Twinhan VisionPlus DVB
[card=113], PCI subsystem ID is 1822:0001
Nov 23 17:22:58 localhost kernel: bttv0: using: Twinhan DST + clones
[card=113,insmod option]
Nov 23 17:22:58 localhost kernel: bttv0: gpio: en=00000000, out=00000000
in=00f7aafd [init]
Nov 23 17:22:58 localhost kernel: bttv0: using tuner=4
Nov 23 17:22:58 localhost kernel: bttv0: add subdevice "dvb0"
Nov 23 17:23:19 localhost kernel: bt878: AUDIO driver version 0.0.0 loaded
Nov 23 17:23:19 localhost kernel: bt878: Bt878 AUDIO function found (0).
Nov 23 17:23:19 localhost kernel: ACPI: PCI Interrupt 0000:01:0a.1[A] ->
Link [APC1] -> GSI 16 (level, high) -> IRQ 21
Nov 23 17:23:19 localhost kernel: bt878(0): Bt878 (rev 17) at 01:0a.1, irq:
21, latency: 32, memory: 0xc0001000
Nov 23 17:23:19 localhost kernel: DVB: registering new adapter (bttv0).
Nov 23 17:23:19 localhost udev[10187]: configured rule in
'/etc/udev/rules.d/udev.rules[36]' applied, 'dvb0.demux0' becomes '%c'
Nov 23 17:23:19 localhost udev[10187]: creating device node
'/dev/dvb/adapter0/demux0'
Nov 23 17:23:20 localhost udev[10191]: configured rule in
'/etc/udev/rules.d/udev.rules[36]' applied, 'dvb0.net0' becomes '%c'
Nov 23 17:23:20 localhost udev[10191]: creating device node
'/dev/dvb/adapter0/net0'
Nov 23 17:23:20 localhost udev[10189]: configured rule in
'/etc/udev/rules.d/udev.rules[36]' applied, 'dvb0.dvr0' becomes '%c'
Nov 23 17:23:20 localhost udev[10189]: creating device node
'/dev/dvb/adapter0/dvr0'
Nov 23 17:23:20 localhost kernel: dst_get_device_id: Recognise [DTT-CI]
Nov 23 17:23:20 localhost kernel:
Nov 23 17:23:20 localhost kernel: DST type flags : 0x2 ts204 0x10 firmware
version = 2
Nov 23 17:23:20 localhost kernel: dst_get_mac: MAC
Address=[01:08:ca:16:57:00]
Nov 23 17:23:20 localhost kernel: DVB: registering frontend 0 (DST DVB-T)...
Nov 23 17:23:20 localhost udev[10235]: configured rule in
'/etc/udev/rules.d/udev.rules[36]' applied, 'dvb0.frontend0' becomes '%c'
Nov 23 17:23:20 localhost udev[10235]: creating device node
'/dev/dvb/adapter0/frontend0'
"/var/log/messages"
Nov 23 17:22:58 localhost kernel: Linux video capture interface: v1.00
Nov 23 17:22:58 localhost kernel: bttv: driver version 0.9.16 loaded
Nov 23 17:22:58 localhost kernel: bttv: using 8 buffers with 2080k (520
pages) each for capture
Nov 23 17:22:58 localhost kernel: bttv: Bt8xx card found (0).
Nov 23 17:22:58 localhost kernel: ACPI: PCI Interrupt 0000:01:0a.0[A] ->
Link [APC1] -> GSI 16 (level, high) -> IRQ 21
Nov 23 17:22:58 localhost kernel: bttv0: Bt878 (rev 17) at 0000:01:0a.0,
irq: 21, latency: 32, mmio: 0xc0000000
Nov 23 17:22:58 localhost kernel: bttv0: detected: Twinhan VisionPlus DVB
[card=113], PCI subsystem ID is 1822:0001
Nov 23 17:22:58 localhost kernel: bttv0: using: Twinhan DST + clones
[card=113,insmod option]
Nov 23 17:22:58 localhost kernel: bttv0: using tuner=4
Nov 23 17:22:58 localhost kernel: bttv0: add subdevice "dvb0"
Nov 23 17:23:19 localhost kernel: bt878: AUDIO driver version 0.0.0 loaded
Nov 23 17:23:19 localhost kernel: bt878: Bt878 AUDIO function found (0).
Nov 23 17:23:19 localhost kernel: ACPI: PCI Interrupt 0000:01:0a.1[A] ->
Link [APC1] -> GSI 16 (level, high) -> IRQ 21
Nov 23 17:23:19 localhost kernel: bt878(0): Bt878 (rev 17) at 01:0a.1, irq:
21, latency: 32, memory: 0xc0001000
Nov 23 17:23:19 localhost kernel: DVB: registering new adapter (bttv0).
Nov 23 17:23:20 localhost kernel:
Nov 23 17:23:20 localhost kernel: DST type flags : 0x2 ts204 0x10 firmware
version = 2
Nov 23 17:23:20 localhost kernel: DVB: registering frontend 0 (DST DVB-T)...
Ive tried to recompile kernel with 2.6.14 but with the same error tuner
messages.. and the read errors if i scan for channels.
Hope you got that information from me that you wanted.
/Regards Anton from Sweden
-----Ursprungligt meddelande-----
Från: Martin Ereth [mailto:martin.ereth at arcor.de]
Skickat: den 23 november 2005 14:52
Till: anton at toprunstudio.com
Kopia: linux-dvb at linuxtv.org
Ämne: Re: [linux-dvb] TwinhanDTV Ter-CI + Linux
Anton Berggren schrieb:
> Hi!
> Ive got problems to get my card working in linux with 2.6.13 kernel.
> my computer finds the card and everything at the boot with no errors or
> warnings.
>
> When i have loaded bttv,dst and dvb-8xx modules and tries to scan for
> channels with "scan dvb-t/se-Vannas" i got this..
Hello!
Sounds like the neccessary modules aren't loaded!
I don't know exactly what device you have.
If it is a usb-stick, the module dvb-usb has to be loaded. Moreover other
modules
beginning dvb* have to be loaded, then.
Please post, what device you have (maybe a link to the picture of the
vendor) and the
output of lsmod.
Greetings
Martin Ereth
More information about the linux-dvb
mailing list