[linux-dvb] Drivers for WinTV NOVA-S-Plus 794 (chipset CX23883)

Merlet Fabien fabien.merlet at nagra.com
Fri Oct 28 10:28:42 CEST 2005


Hi again, 

Card is a: 
	Hauppauge WinTV Nova-S-Plus 92001 Rev B1B1 LF
	Chipsets: 	Broadcast decoder CX23883-19
			QPSK Demod CX24123-11Z

Here is the result of dmesg with insmod card=0 and card=18 options.

N.B: I did not remove any line to avoid deleting useful information
I also added "lsmod" at the end after the "modprobe batch" below and
lspci and "lspci -vn" if it can help. Sorry if message is quite long...

TIA
Fabien

------------------------------------------------------------------------
----
Linux version 2.6.13.4 (root at pc0219) (gcc version 3.3.5 (Debian
1:3.3.5-13)) #2 Tue Oct 25 17:10:10 CEST 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000ffec000 (usable)
 BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data)
 BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved)
 BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65516
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 61420 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS                                  ) @ 0x000f7160
ACPI: RSDT (v001 ASUS   CUV4X_E  0x30303031 MSFT 0x31313031) @
0x0ffec000
ACPI: FADT (v001 ASUS   CUV4X_E  0x30303031 MSFT 0x31313031) @
0x0ffec080
ACPI: BOOT (v001 ASUS   CUV4X_E  0x30303031 MSFT 0x31313031) @
0x0ffec040
ACPI: DSDT (v001   ASUS CUV4X_E  0x00001000 MSFT 0x0100000b) @
0x00000000
Allocating PCI resources starting at 10000000 (gap: 10000000:efff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro 
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01201000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 799.891 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 255340k/262064k available (2331k kernel code, 6172k reserved,
967k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay using timer specific routine.. 1602.92 BogoMIPS
(lpj=3205855)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0820)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0cb0, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: f8800000-f9dfffff
  PREFETCH window: f9f00000-fbffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
Simple Boot Flag at 0x3a set to 0x1
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
Initializing Cryptographic API
PCI: Disabling Via external APIC routing
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA ProSavage PM133/PL133/PN133 chipset
agpgart: AGP aperture is 32M @ 0xfc000000
[drm] Initialized drm 1.0.0 20040925
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-d (2.4 port) Nov-17-2001  Donald Becker
<becker at scyld.com>
  http://www.scyld.com/network/drivers.html
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Enabling device 0000:00:09.0 (0004 -> 0007)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
tulip0:  MII transceiver #1 config 3100 status 7829 advertising 01e1.
eth0: Lite-On 82c168 PNIC rev 32 at 0001b400, 00:C0:F0:3E:AD:6B, IRQ 11.
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:04.1
    ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD800BB-00JHC0, ATA DISK drive
hdb: IBM-DTLA-307020, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ASUS DVD-ROM E608, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2
hdb: max request size: 128KiB
hdb: 40188960 sectors (20576 MB) w/1916KiB Cache, CHS=42528/15/63,
UDMA(100)
hdb: cache flushes not supported
 hdb: hdb1 hdb2 < hdb5 >
libata version 1.12 loaded.
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard on isa0060/serio0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 160k freed
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
Adding 2097136k swap on /dev/hda2.  Priority:-1 extents:1
EXT3 FS on hda1, internal journal
via686a 0000:00:04.4: base address not set - upgrade BIOS or use
force_addr=0xaddr
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKC] -> GSI 5 (level, low)
-> IRQ 5
uhci_hcd 0000:00:04.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:04.2: irq 5, io base 0x0000d400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKC] -> GSI 5 (level, low)
-> IRQ 5
uhci_hcd 0000:00:04.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:04.3: irq 5, io base 0x0000d000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 7 ports detected
usb 1-2.1: new full speed USB device using uhci_hcd and address 3
usb 1-2.5: new full speed USB device using uhci_hcd and address 4
usb 1-2.6: new full speed USB device using uhci_hcd and address 5
saa7146: register extension 'budget dvb'.
PCI: Enabling device 0000:00:0a.0 (0004 -> 0006)
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low)
-> IRQ 5
saa7146: found saa7146 @ mem d0964000 (revision 1, irq 5)
(0x13c2,0x1004).
DVB: registering new adapter (TT-Budget/WinTV-NOVA-C  PCI).
adapter has MAC addr = 00:d0:5c:02:55:17
DVB: registering frontend 0 (VLSI VES1820 DVB-C)...
cx2388x v4l2 driver version 0.0.5 loaded
PCI: Enabling device 0000:00:0b.0 (0014 -> 0016)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 10 (level,
low) -> IRQ 10
cx88[0]: Your board isn't known (yet) to the driver.  You can
cx88[0]: try to pick one of the existing card configs via
cx88[0]: card=<n> insmod option.  Updating to the latest
cx88[0]: version might help as well.
cx88[0]: Here is a list of valid choices for the card=<n> insmod option:
cx88[0]:    card=0 -> UNKNOWN/GENERIC
cx88[0]:    card=1 -> Hauppauge WinTV 34xxx models
cx88[0]:    card=2 -> GDI Black Gold
cx88[0]:    card=3 -> PixelView
cx88[0]:    card=4 -> ATI TV Wonder Pro
cx88[0]:    card=5 -> Leadtek Winfast 2000XP Expert
cx88[0]:    card=6 -> AverTV Studio 303 (M126)
cx88[0]:    card=7 -> MSI TV- at nywhere Master
cx88[0]:    card=8 -> Leadtek Winfast DV2000
cx88[0]:    card=9 -> Leadtek PVR 2000
cx88[0]:    card=10 -> IODATA GV-VCP3/PCI
cx88[0]:    card=11 -> Prolink PlayTV PVR
cx88[0]:    card=12 -> ASUS PVR-416
cx88[0]:    card=13 -> MSI TV- at nywhere
cx88[0]:    card=14 -> KWorld/VStream XPert DVB-T
cx88[0]:    card=15 -> DViCO FusionHDTV DVB-T1
cx88[0]:    card=16 -> KWorld LTV883RF
cx88[0]:    card=17 -> DViCO FusionHDTV 3 Gold-Q
cx88[0]:    card=18 -> Hauppauge Nova-T DVB-T
cx88[0]:    card=19 -> Conexant DVB-T reference design
cx88[0]:    card=20 -> Provideo PV259
cx88[0]:    card=21 -> DViCO FusionHDTV DVB-T Plus
cx88[0]:    card=22 -> pcHDTV HD3000 HDTV
cx88[0]:    card=23 -> digitalnow DNTV Live! DVB-T
cx88[0]:    card=24 -> Hauppauge WinTV 28xxx (Roslyn) models
cx88[0]:    card=25 -> Digital-Logic MICROSPACE Entertainment Center
(MEC)
cx88[0]:    card=26 -> IODATA GV/BCTV7E
cx88[0]:    card=27 -> PixelView PlayTV Ultra Pro (Stereo)
cx88[0]:    card=28 -> DViCO FusionHDTV 3 Gold-T
cx88[0]:    card=29 -> ADS Tech Instant TV DVB-T PCI
cx88[0]:    card=30 -> TerraTec Cinergy 1400 DVB-T
cx88[0]:    card=31 -> DViCO FusionHDTV 5 Gold
cx88[0]: subsystem: 0070:9202, board: UNKNOWN/GENERIC
[card=0,autodetected]
TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[0]/0: found at 0000:00:0b.0, rev: 5, irq: 10, latency: 32, mmio:
0xf6000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx2388x blackbird driver version 0.0.5 loaded
cx2388x dvb driver version 0.0.5 loaded
hdc: ATAPI 40X DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
eth0: Setting full-duplex based on MII#1 link partner capability of
05e1.
saa7146: register extension 'dvb'.
saa7146: register extension 'budget_ci dvb'.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level,
low) -> IRQ 11
[drm] Initialized mga 3.1.0 20021029 on minor 0: Matrox Graphics, Inc.
MGA G400 AGP
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
ACPI: PCI interrupt for device 0000:00:0b.0 disabled
cx2388x dvb driver version 0.0.5 loaded
cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-T DVB-T
[card=18,insmod option]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
tveeprom(cx88xx internal): Huh, no eeprom present (err=-121)?
cx88[0]: warning: unknown hauppauge model #0
cx88[0]: error: unknown hauppauge tuner 0x00
cx88[0]: registered IR remote control
PCI: Enabling device 0000:00:0b.2 (0014 -> 0016)
ACPI: PCI Interrupt 0000:00:0b.2[A] -> Link [LNKB] -> GSI 10 (level,
low) -> IRQ 10
cx88[0]/2: found at 0000:00:0b.2, rev: 5, irq: 10, latency: 32, mmio:
0xf4000000
cx88[0]/2: cx2388x based dvb card
cx22702_readreg: readreg error (ret == -121)
cx88[0]: frontend initialization failed
cx88[0]/2: cx8802_stop_dma
ACPI: PCI interrupt for device 0000:00:0b.2 disabled
cx88-dvb: probe of 0000:00:0b.2 failed with error -1
saa7146: unregister extension 'budget dvb'.
ACPI: PCI interrupt for device 0000:00:0a.0 disabled
saa7146: unregister extension 'dvb'.
saa7146: unregister extension 'budget_ci dvb'.
saa7146: register extension 'dvb'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget dvb'.
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low)
-> IRQ 5
saa7146: found saa7146 @ mem d09a0000 (revision 1, irq 5)
(0x13c2,0x1004).
DVB: registering new adapter (TT-Budget/WinTV-NOVA-C  PCI).
adapter has MAC addr = 00:d0:5c:02:55:17
DVB: registering frontend 0 (VLSI VES1820 DVB-C)...

------------------------------------------------------------------------
----
Lsmod after having executed batch below:
------------------------------------------------------------------------
----

Module                  Size  Used by
budget                 11264  0 
budget_ci              14464  0 
tda1004x               16260  1 budget_ci
budget_core             9604  2 budget,budget_ci
dvb_ttpci             100668  0 
l64781                  8068  2 budget,dvb_ttpci
saa7146_vv             50688  1 dvb_ttpci
saa7146                18952  5
budget,budget_ci,budget_core,dvb_ttpci,saa7146_vv
ves1820                 6276  2 budget,dvb_ttpci
stv0299                11912  3 budget,budget_ci,dvb_ttpci
tda8083                 6788  2 budget,dvb_ttpci
stv0297                 9728  1 dvb_ttpci
sp8870                  8204  1 dvb_ttpci
ves1x93                 7300  2 budget,dvb_ttpci
ttpci_eeprom            2944  2 budget_core,dvb_ttpci
cx88_dvb                9732  0 
cx8802                 11908  1 cx88_dvb
mt352                   7044  1 cx88_dvb
or51132                11140  1 cx88_dvb
video_buf_dvb           6660  1 cx88_dvb
lgdt330x                8476  1 cx88_dvb
cx22702                 6916  1 cx88_dvb
dvb_pll                 9604  3 cx88_dvb,or51132,cx22702
cx88xx                 59424  2 cx88_dvb,cx8802
i2c_algo_bit           10120  1 cx88xx
ir_common               8452  1 cx88xx
btcx_risc               5128  2 cx8802,cx88xx
tveeprom               12176  1 cx88xx
mga                    60288  1 
ide_cd                 43396  0 
cdrom                  41376  1 ide_cd
firmware_class         10368  5
budget_ci,tda1004x,dvb_ttpci,sp8870,or51132
tuner                  38696  0 
video_buf              22148  5
saa7146_vv,cx88_dvb,cx8802,video_buf_dvb,cx88xx
s5h1420                10372  1 budget
dvb_core               81960  5
budget,budget_ci,budget_core,dvb_ttpci,video_buf_dvb
uhci_hcd               34064  0 
usbcore               122364  2 uhci_hcd
parport_pc             40900  0 
parport                37320  1 parport_pc
via686a                19992  0 
w83781d                33188  0 
i2c_sensor              3712  2 via686a,w83781d
i2c_isa                 2304  0 
i2c_viapro              8336  0 
i2c_core               21392  28
budget,budget_ci,tda1004x,budget_core,dvb_ttpci,l64781,ves1820,stv0299,t
da8083,stv0297,sp8870,ves1x93,ttpci_eeprom,cx88_dvb,mt352,or51132,lgdt33
0x,cx22702,cx88xx,i2c_algo_bit,tveeprom,tuner,s5h1420,via686a,w83781d,i2
c_sensor,i2c_isa,i2c_viapro
evdev                   9472  0

------------------------------------------------------------------------
----
Lspci and lspci -vn
------------------------------------------------------------------------
----

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage
PM133] (rev c4)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo
MVP3/Pro133x AGP]
0000:00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
South] (rev 40)
0000:00:04.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 16)
0000:00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB
1.1 Controller (rev 16)
0000:00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super
ACPI] (rev 40)
0000:00:08.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
0000:00:09.0 Ethernet controller: Lite-On Communications Inc LNE100TX
(rev 20)
0000:00:0a.0 Multimedia controller: Philips Semiconductors SAA7146 (rev
01)
0000:00:0b.0 Multimedia video controller: Conexant Winfast TV2000 XP
(rev 05)
0000:00:0b.1 Multimedia controller: Conexant: Unknown device 8801 (rev
05)
0000:00:0b.2 Multimedia controller: Conexant: Unknown device 8802 (rev
05)
0000:00:0b.4 Multimedia controller: Conexant: Unknown device 8804 (rev
05)
0000:01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400
AGP (rev 82)
0000:00:00.0 0600: 1106:0605 (rev c4)
	Subsystem: 1043:80e7
	Flags: bus master, medium devsel, latency 0
	Memory at fc000000 (32-bit, prefetchable) [size=32M]
	Capabilities: <available only to root>

0000:00:01.0 0604: 1106:8598
	Flags: bus master, 66MHz, medium devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: f8800000-f9dfffff
	Prefetchable memory behind bridge: f9f00000-fbffffff
	Capabilities: <available only to root>

0000:00:04.0 0601: 1106:0686 (rev 40)
	Subsystem: 1043:80e7
	Flags: bus master, stepping, medium devsel, latency 0
	Capabilities: <available only to root>

0000:00:04.1 0101: 1106:0571 (rev 06) (prog-if 8a [Master SecP PriP])
	Flags: bus master, stepping, medium devsel, latency 32
	I/O ports at d800 [size=16]
	Capabilities: <available only to root>

0000:00:04.2 0c03: 1106:3038 (rev 16)
	Subsystem: 0925:1234
	Flags: bus master, medium devsel, latency 32, IRQ 5
	I/O ports at d400 [size=32]
	Capabilities: <available only to root>

0000:00:04.3 0c03: 1106:3038 (rev 16)
	Subsystem: 0925:1234
	Flags: bus master, medium devsel, latency 32, IRQ 5
	I/O ports at d000 [size=32]
	Capabilities: <available only to root>

0000:00:04.4 0600: 1106:3057 (rev 40)
	Flags: medium devsel, IRQ 9
	Capabilities: <available only to root>

0000:00:08.0 0401: 1274:5880 (rev 02)
	Subsystem: 1274:2000
	Flags: bus master, slow devsel, latency 32, IRQ 255
	I/O ports at b800 [disabled] [size=64]
	Capabilities: <available only to root>

0000:00:09.0 0200: 11ad:0002 (rev 20)
	Subsystem: 2646:f002
	Flags: bus master, medium devsel, latency 32, IRQ 11
	I/O ports at b400 [size=256]
	Memory at f8000000 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at 10000000 [disabled] [size=256K]

0000:00:0a.0 0480: 1131:7146 (rev 01)
	Subsystem: 13c2:1004
	Flags: bus master, medium devsel, latency 32, IRQ 5
	Memory at f7800000 (32-bit, non-prefetchable) [size=512]

0000:00:0b.0 0400: 14f1:8800 (rev 05)
	Subsystem: 0070:9202
	Flags: medium devsel, IRQ 10
	Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: <available only to root>

0000:00:0b.1 0480: 14f1:8801 (rev 05)
	Subsystem: 0070:9202
	Flags: bus master, medium devsel, latency 32, IRQ 255
	Memory at f5000000 (32-bit, non-prefetchable) [disabled]
[size=16M]
	Capabilities: <available only to root>

0000:00:0b.2 0480: 14f1:8802 (rev 05)
	Subsystem: 0070:9202
	Flags: medium devsel, IRQ 10
	Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: <available only to root>

0000:00:0b.4 0480: 14f1:8804 (rev 05)
	Subsystem: 0070:9202
	Flags: bus master, medium devsel, latency 32, IRQ 255
	Memory at f3000000 (32-bit, non-prefetchable) [disabled]
[size=16M]
	Capabilities: <available only to root>

0000:01:00.0 0300: 102b:0525 (rev 82)
	Subsystem: 102b:0541
	Flags: bus master, medium devsel, latency 64, IRQ 11
	Memory at fa000000 (32-bit, prefetchable) [size=32M]
	Memory at f9000000 (32-bit, non-prefetchable) [size=16K]
	Memory at f8800000 (32-bit, non-prefetchable) [size=8M]
	Expansion ROM at f9fe0000 [disabled] [size=128K]
	Capabilities: <available only to root>

>-----Original Message-----
>From: Michael Krufky [mailto:mkrufky at m1k.net]
>Sent: mercredi, 26. octobre 2005 14:23
>To: Merlet Fabien
>Cc: linux-dvb at linuxtv.org
>Subject: Re: [linux-dvb] Drivers for WinTV NOVA-S-Plus 794 (chipset
>CX23883)
>
>Merlet Fabien wrote:
>
>>>>Previous version of this Hauppauge card was using a saa7146 chipset.
>>>>
>>>>They now changed it for a Conexant CX23883.
>>>>
>>>>Does someone can help me to find the drivers for this card?
>>>>
>>>>I've not seen anything in the latest kernel 2.6.13 media/common
>>>>directory or in CVS repository ...
>>>>
>>>The glue code for this will be handled by video4linux... You can try
>>>cx88 card #18 -- it might work ... But probably will not... If you
would
>>>
>>>
>>>provide more info about the card, I would be happy to assist in
adding
>>>support for it. First try cx88 card=18 , if that doesnt work, then
>>>please provide your dmesg, "lspci -vn" , and tell us every chip that
you
>>>
>>>
>>>can see on the board, in addition any writing that you might see on
the
>>>"tin box" ... You might have to peel off a sticker in order to get to
it.
>>>
>>>
>> Hi Mike,
>>
>>Txs for your support,
>>I'm trying to configure this and I have some troubles and some doubts.
>>I will provide you feedback once I'm sure of the results.
>>
>>Regards
>>Fabien
>>
>>
>Fabien-
>
>Like I said, I am willing to help.  Even a non-working dmesg log full
of
>errors can help me to figure out what you might need.  Try doing what I
>mentioned above, although I realized it would help if you also added
the
>parameter i2c_scan=1 to your modprobe args.   I also realized that I've
>given bad instructions for the modules.  Do this:
>
>First, remove the modules:
>
>modprobe -r cx88-dvb
>modprobe -r cx88-blackbird
>modprobe -r cx8802
>modprobe -r cx8800
>modprobe -r cx88xx
>
>Then insert them like this:
>
>modprobe cx88xx card=18 i2c_scan=1
>modprobe cx88-dvb
>
>I'd be interested to see what dmesg looks like after the above.



More information about the linux-dvb mailing list