[linux-dvb] Two card config question

Philip Prindeville philipp_subx at redfish-solutions.com
Sat Oct 29 09:05:06 CEST 2005


Hi.

I'm using two cards in a box (using a passive riser card).  I'm seeing
the following logging:

IrDA: Registered device irda0 (via-ircc)
Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.4 loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 12 (level, 
low) -> IRQ 12
cx88[0]: subsystem: 7063:3000, board: pcHDTV HD3000 HDTV 
[card=22,autodetected]
tuner 0-0061: chip found @ 0xc2 (cx88[0])
tuner 0-0061: type set to 52 (Thomson DDT 7610 (ATSC/NTSC))
cx88[0]/0: found at 0000:00:14.0, rev: 5, irq: 12, latency: 32, mmio: 
0xde000000cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
cx2388x dvb driver version 0.0.4 loaded
ACPI: PCI Interrupt 0000:00:14.2[A] -> Link [LNKB] -> GSI 12 (level, 
low) -> IRQ 12
cx88[0]/2: found at 0000:00:14.2, rev: 5, irq: 12, latency: 32, mmio: 
0xdf000000cx88[0]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 0 (pcHDTV HD3000 HDTV)...
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 10 (level, 
low) -> IRQ 10
bttv0: Bt878 (rev 17) at 0000:00:13.0, irq: 10, latency: 32, mmio: 
0xe0001000
bttv0: detected: ChainTech digitop DST-1000 DVB-S [card=113], PCI 
subsystem ID is 270f:fc00
bttv0: using: Twinhan DST + clones [card=113,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv0: using tuner=4
bttv0: add subdevice "dvb0"
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKA] -> GSI 10 (level, 
low) -> IRQ 10
bt878(0): Bt878 (rev 17) at 00:13.1, irq: 10, latency: 32, memory: 
0xe0002000
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 7 (level, low) 
-> IRQ 7

And lspci reports:

00:13.0 Multimedia video controller: Brooktree Corporation Bt878 Video 
Capture (rev 11)
00:13.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture 
(rev 11)
00:14.0 Multimedia video controller: Conexant Winfast TV2000 XP (rev 05)
00:14.2 Multimedia controller: Conexant: Unknown device 8802 (rev 05)


The relevant portion of my /etc/modprobe.conf file looks like:

# DVB stuff
alias char-major-81 cx88-dvb
alias char-major-81-0 cx8800
alias char-major-81-1 bttv
options dvb_core dvb_shutdown_timeout=0
options bttv i2c_hw=1 card=0x71
install bt878 /sbin/modprobe --ignore-install bt878
install dst /sbin/modprobe --ignore-install dst
install dvb_bt8xx /sbin/modprobe --ignore-install dvb_bt8xx
install cx88-atsc /sbin/modprobe cx8800;/sbin/modprobe --ignore-install 
cx88-atsc
install cx88-dvb /sbin/modprobe cx8800;/sbin/modprobe --ignore-install 
cx88-dvb
install btcx-risc /sbin/modprobe tuner;/sbin/modprobe --ignore-install 
btcx-risc

What am I overlooking?  I'm not seeing the second
frontend device being registered...

Thanks,

-Philip




More information about the linux-dvb mailing list