[linux-dvb] Twinhan VisionPlus VP-TER-3040-B, not working with CI, 2.6.15-r1

tomas tomas at riverman.com
Tue Feb 14 00:47:44 CET 2006


Hi,
I have a Twinhan VisionPlus VP-TER-3040-B and using 2.6.15-r1 kernel.
My problem is that I can only tune in channels when the CI is disconnected.
Some hints what I could do to make it work?

Here is what ca_zap tells me (after tzap has found the channel) and dmesg:

 $ ca_zap -c channels.conf  -t ter -n ZTV
 Using Adpater=[/dev/dvb/adapter0]
  Frontend=[/dev/dvb/adapter0/frontend0]
  Demux=[/dev/dvb/adapter0/demux0]
  Slot=[/dev/dvb/adapter0/ca0]
 Parsing channels.conf
 Terrestrial frontend
 ERROR: transmission_mode field syntax error
 Service ID=[0]
 parse_pat: ----------------->parse PAT section
 parse_pat: PAT => Section Length=[53], TS ID=[1111]
 parse_si: PMT PID = [16]
 parse_si: PAT: Close Demux /dev/dvb/adapter0/demux0

Or ...

 $ ca_zap -c channels.conf  -n ZTV
 Using Adpater=[/dev/dvb/adapter0]
  Frontend=[/dev/dvb/adapter0/frontend0]
  Demux=[/dev/dvb/adapter0/demux0]
  Slot=[/dev/dvb/adapter0/ca0]
 Parsing channels.conf
 parse_pat: ----------------->parse PAT section
 parse_pat: PAT => Section Length=[53], TS ID=[1111]
 parse_si: PMT PID = [16]
 parse_si: PAT: Close Demux /dev/dvb/adapter0/demux0

And this is what I got from dmesg
 ...
 i2c /dev entries driver
 Linux video capture interface: v1.00
 bttv: driver version 0.9.16 loaded
 bttv: using 8 buffers with 2080k (520 pages) each for capture
 bttv: Bt8xx card found (0).
 ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI 9 (level,  low) -> IRQ 9 
 bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 9, latency: 32, mmio: 0xe7000000
 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001
 bttv0: using: Twinhan DST + clones [card=113,autodetected]
 bttv0: gpio: en=00000000, out=00000000 in=00f500fd [init]
 bttv0: using tuner=4
 bttv0: add subdevice "dvb0"
 bt878: AUDIO driver version 0.0.0 loaded
 bt878: Bt878 AUDIO function found (0).
 ACPI: PCI Interrupt 0000:00:09.1[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
 bt878(0): Bt878 (rev 17) at 00:09.1, irq: 9, latency: 32, memory: 0xe6800000
 DVB: registering new adapter (bttv0).
 dst_get_device_id: Recognise [DTT-CI]

 DST type flags : 0x1 newtuner 0x2 ts204 0x10 firmware version = 2
 dst_get_mac: MAC Address=[00:08:ca:17:cd:00]
 dst_ca_attach: registering DST-CA device
 DVB: registering frontend 0 (DST DVB-T)...
 ...

regards,
Tomas






More information about the linux-dvb mailing list