[linux-dvb] DViCO FusionHDTV DVB-T Dual

[Dean Macauley]

Hi,

I have purchased this card, and I have been struggling to get things 
working with gentoo (kernel 2.6.16).  I am fairly new to playing with 
linux at this level but I have been learning much thank you to many 
posts etc...

I have a question regarding this card and what I should expect in terms 
devices...

Should I see two adapters under /dev/dvb/ ?  At the moment, things seem 
okay in dmesg (see below) however, I only have one adapter in 
/dev/dvb/.  The other is /dev/vbi0 ...

I have discovered that one tuner is PCI while the other is USB...

I am loading the following modules:

Module                  Size  Used by
dvb_usb_cxusb          23684  0
mt352                   8196  1 dvb_usb_cxusb
lgdt330x                9692  1 dvb_usb_cxusb
cx22702                 8068  1 dvb_usb_cxusb
dvb_usb                18248  1 dvb_usb_cxusb
dvb_core               77148  1 dvb_usb
dvb_pll                12356  3 dvb_usb_cxusb,cx22702,dvb_usb
cx8800                 30412  0
cx88xx                 62500  1 cx8800
i2c_algo_bit           10184  1 cx88xx
video_buf              20164  2 cx8800,cx88xx
ir_common              10756  1 cx88xx
tveeprom               17040  1 cx88xx
compat_ioctl32          9856  1 cx8800
v4l1_compat            12804  1 cx8800
v4l2_common            10304  2 cx8800,compat_ioctl32
btcx_risc               6216  2 cx8800,cx88xx
videodev               10880  2 cx8800,cx88xx

when I try to modprobe cx88-dvb, I get an error that initialisation 
failed, while modprobe cx8800 seems to work...  Have I got it right?  Or 
should I expect two adapters in /dev/dvb?

Thanks in advance!

Dean.

P.S.  dmesg output below

CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual 
Digital [card=44,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[0]/0: found at 0000:05:06.0, rev: 5, irq: 58, latency: 32, mmio: 
0xd3000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
set_control id=0x980900 reg=0x310110 val=0x00 (mask 0xff)
set_control id=0x980901 reg=0x310110 val=0x3f00 (mask 0xff00)
set_control id=0x980903 reg=0x310118 val=0x00 (mask 0xff)
set_control id=0x980902 reg=0x310114 val=0x5a7f (mask 0xffff)
set_control id=0x980909 reg=0x320594 val=0x40 (mask 0x40) [shadowed]
set_control id=0x980905 reg=0x320594 val=0x20 (mask 0x3f) [shadowed]
set_control id=0x980906 reg=0x320598 val=0x40 (mask 0x7f) [shadowed]
dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software 
demuxer.
DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual USB).
dvb-usb: recv bulk message failed: -110
dvb-usb: no frontend was attached by 'DViCO FusionHDTV DVB-T Dual USB'
input: IR-receiver inside an USB DVB receiver as /class/input/input4
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: DViCO FusionHDTV DVB-T Dual USB successfully initialized and 
connected.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20060629/c4603c7c/attachment-0001.htm