[linux-dvb] Trouble with Pinnacle 310i DVB-T

KevinLuX kevinlux at karondimonio.it
Wed Oct 11 20:10:48 CEST 2006


Cabrito Estrabico ha scritto:
> Hello,
> I'm Ubuntu 6.06 LTS user on kernell 2.6.15-27-k7 with the last v4l-dvb 
> sources compiled to make
> this Pinnacle 310i runing dvb-t with dvb-fe-tda10046.fw firmware.
> Being from France I use the secam videostandard and everything is ok 
> for analogue tv.
>
> Here is  the dmesg  output when probing saa7134 module with secam=l 
> option :
>
> [17179647.088000] saa7130/34: v4l2 driver version 0.2.14 loaded
> [17179647.088000] **** SET: Misaligned resource pointer: f6594902 Type 
> 07 Len 0
> [17179647.092000] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
> [17179647.092000] ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] 
> -> GSI 17 (level, low) -> IRQ 66
> [17179647.092000] saa7133[0]: found at 0000:05:07.0, rev: 208, irq: 
> 66, latency: 32, mmio: 0xd3000000
> [17179647.092000] saa7133[0]: subsystem: 11bd:002f, board: Pinnacle 
> PCTV 310i [card=101,autodetected]
> [17179647.092000] saa7133[0]: board init: gpio is 600c000
> [17179647.240000] saa7133[0]: i2c eeprom 00: bd 11 2f 00 54 20 1c 00 
> 43 43 a9 1c 55 d2 b2 92
> [17179647.240000] saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff 
> 00 30 8d 2c 1a 07 ff ff
> [17179647.240000] saa7133[0]: i2c eeprom 20: 01 2c 01 02 02 01 04 31 
> 98 ff 00 a6 ff 21 00 c2
> [17179647.240000] saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff ff 
> 0c 22 17 77 03 1c 88 97
> [17179647.240000] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff 
> ff ff ff ff ff ff ff ff
> [17179647.240000] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff 
> ff ff ff ff ff ff ff ff
> [17179647.240000] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff 
> ff ff ff ff ff ff ff ff
> [17179647.240000] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff 
> ff ff ff ff ff ff ff ff
> [17179647.344000] tuner 5-004b: chip found @ 0x96 (saa7133[0])
> [17179647.396000] tuner 5-004b: setting tuner address to 61
> [17179647.436000] tuner 5-004b: type set to tda8290+75a
> [17179647.508000] saa7133[0]: registered device video0 [v4l2]
> [17179647.508000] saa7133[0]: registered device vbi0
> [17179647.508000] saa7133[0]: registered device radio0
> [17179647.548000] saa7134 ALSA driver for DMA sound loaded
> [17179647.548000] saa7133[0]/alsa: saa7133[0] at 0xd3000000 irq 66 
> registered as card -1
>
>
>
> next, modprobe  saa1734-dvb :
>
> [17179811.560000] DVB: registering new adapter (saa7133[0]).
> [17179811.560000] DVB: registering frontend 0 (Philips TDA10046H 
> DVB-T)...
>
> then, scanning tuning data file :
>
> [17179869.076000] tda1004x: setting up plls for 48MHz sampling clock
> [17179869.344000] tda1004x: found firmware revision 20 -- ok
>
> But scan result is :                           
> ERROR: initial tuning failed
> dumping lists (0 services)
> Done.
>
> and femon give :
>
> using '/dev/dvb/adapter0/frontend0'
> FE: Philips TDA10046H DVB-T (TERRESTRIAL)
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> status 00 | signal 8080 | snr 7f7f | ber 0001fffe | unc 00000000 |
> ..............  ....................  .............  
> .....................  ........................
> ..............  ....................  .............  
> .....................  ........................
> etc etc
>
> I want to add that I've already manage to have dvb-t on my Ubuntu with 
> an other card.
> So, from where come this trouble ; hardware, configuration ?
>
> Thank you for any help you could give.
>
> Cabrito
>
>
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
seems that you have done all steps like but here i repeat :

make all & make install from v4l dir

perl *path_to_v4l_dir*/linux/Documentation/dvb/get_dvb_firmware tda10046  //to get firmware

cp *path_to_v4l_dir*/linux/Documentation/dvb/get_dvb_firmware/dvb-fe-tda10046.fw /lib/firmware  //copy firmware where hotplug search for it

reboot ;) it's better ;)

I have ubuntu 606 like you. Try to compile a new vanilla kernel from source.
I say this because when i have tried to compile current v4l my messages tell me the to get 
work perfectly all features i have to compile at least kernel 2.6.16. So i have download and
compile 2.6.18 kernel. If you have problems look at this to compile a new kernel under ubuntu :
http://www.ubuntuforums.org/showthread.php?t=217657&highlight=howto+grub

I don't know if is this the problem but if you receive during v4l compilation the same message,
try to update kernel.

Maybe other people can tell u more than me ;)

best regards

kev




















More information about the linux-dvb mailing list