[linux-dvb] dvb_usb_dib0700: filter timeout pid 0x0011

Wesley Lim wesleylim at gmail.com
Wed Sep 5 06:42:33 CEST 2007


Does the following mean that
1. something is wrong with my USB stick?
2. the signal I'm receiving is too weak?
3. support for this device is just not there yet?
4. not enough information supplied -> what should I try?

Thanks so much!

kernel 2.6.21.5
v4l-dvb (03 Sep 2007)
Bus 4 Device 2: ID 2040:7060 Hauppauge
firmware dvb-usb-dib0700-03-pre1.fw
(500Mhz is a non-signal, 538Mhz is a known DVB-T signal)
the output of ./scan for all known DVB-T frequencies is the same as
for 538Mhz, and the output for all non-signals is the same as for
500Mhz

./scan shows:
scanning sg-Singapore
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 500000000 3 9 9 6 2 4 4
initial transponder 538000000 3 9 9 6 2 4 4
>>> tune to: 500000000:INVERSION_AUTO:BANDWIDTH_AUTO:FEC_AUTO:FEC_AUTO:QAM_AUTO:TRANSMISSION_MODE_AUTO:GUARD_INTERVAL_AUTO:HIERARCHY_AUTO
WARNING: >>> tuning failed!!!
>>> tune to: 500000000:INVERSION_AUTO:BANDWIDTH_AUTO:FEC_AUTO:FEC_AUTO:QAM_AUTO:TRANSMISSION_MODE_AUTO:GUARD_INTERVAL_AUTO:HIERARCHY_AUTO
(tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 538000000:INVERSION_AUTO:BANDWIDTH_AUTO:FEC_AUTO:FEC_AUTO:QAM_AUTO:TRANSMISSION_MODE_AUTO:GUARD_INTERVAL_AUTO:HIERARCHY_AUTO
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
dumping lists (0 services)
Done.





./scan -vvvv shows:
scanning sg-Singapore
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 500000000 3 9 9 6 2 4 4
initial transponder 538000000 3 9 9 6 2 4 4
>>> tune to: 500000000:INVERSION_AUTO:BANDWIDTH_AUTO:FEC_AUTO:FEC_AUTO:QAM_AUTO:TRANSMISSION_MODE_AUTO:GUARD_INTERVAL_AUTO:HIERARCHY_AUTO
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
WARNING: >>> tuning failed!!!
>>> tune to: 500000000:INVERSION_AUTO:BANDWIDTH_AUTO:FEC_AUTO:FEC_AUTO:QAM_AUTO:TRANSMISSION_MODE_AUTO:GUARD_INTERVAL_AUTO:HIERARCHY_AUTO
(tuning failed)
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
>>> tuning status == 0x01
WARNING: >>> tuning failed!!!
>>> tune to: 538000000:INVERSION_AUTO:BANDWIDTH_AUTO:FEC_AUTO:FEC_AUTO:QAM_AUTO:TRANSMISSION_MODE_AUTO:GUARD_INTERVAL_AUTO:HIERARCHY_AUTO
>>> tuning status == 0x1b
add_filter:1377: add filter pid 0x0000
start_filter:1317: start filter pid 0x0000 table_id 0x00
update_poll_fds:1297: poll fd 4
add_filter:1377: add filter pid 0x0011
start_filter:1317: start filter pid 0x0011 table_id 0x42
update_poll_fds:1297: poll fd 5
update_poll_fds:1297: poll fd 4
add_filter:1377: add filter pid 0x0010
start_filter:1317: start filter pid 0x0010 table_id 0x40
update_poll_fds:1297: poll fd 6
update_poll_fds:1297: poll fd 5
update_poll_fds:1297: poll fd 4
WARNING: filter timeout pid 0x0011
remove_filter:1385: remove filter pid 0x0011
stop_filter:1363: stop filter pid 0x0011
update_poll_fds:1297: poll fd 6
update_poll_fds:1297: poll fd 4
WARNING: filter timeout pid 0x0000
remove_filter:1385: remove filter pid 0x0000
stop_filter:1363: stop filter pid 0x0000
update_poll_fds:1297: poll fd 6
WARNING: filter timeout pid 0x0010
remove_filter:1385: remove filter pid 0x0010
stop_filter:1363: stop filter pid 0x0010
dumping lists (0 services)
Done.





./tzap shows:
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
tuning to 602000000 Hz
video pid 0x00a1, audio pid 0x0052
status 1b | signal 5bbb | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK
status 1b | signal 5657 | snr 0000 | ber 001fffff | unc 00000008 | FE_HAS_LOCK
status 1b | signal 562e | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK
status 1b | signal 567e | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK
status 1b | signal 56da | snr 0000 | ber 001fffff | unc 00000000 | FE_HAS_LOCK





dmesg shows:
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
dib0700: loaded with support for 5 different device-types
dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Hauppauge Nova-T Stick)
DVB: registering frontend 0 (DiBcom 7000PC)...
MT2060: successfully identified (IF1 = 1220)
input: IR-receiver inside an USB DVB receiver as /class/input/input1
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_dib0700



More information about the linux-dvb mailing list