[linux-dvb] HVR-4000

Craig Whitmore lennon at orcon.net.nz
Wed Jan 23 11:13:28 CET 2008


> Good job on the wiki so far. At last there is one place that can serve as 
> a showcase for all the hard work done.


After a number of patches I have it compiling and booting with HVR4000 with 
multiple frontends showing up (test tomorrow if they actually work)

cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 
DVB-S/S2/T/Hybrid [card=59,autodetected]
cx88[0]: TV tuner type 63, Radio tuner type -1
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
cx88[0]: i2c init: enabling analog demod on HVR1300/3000/4000 tuner
tveeprom 2-0050: Hauppauge model 69009, rev B2D3, serial# 2807241
tveeprom 2-0050: MAC address is 00-0D-FE-2A-D5-C9
tveeprom 2-0050: tuner model is Philips FMD1216MEX (idx 133, type 63)
tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) 
ATSC/DVB Digital (eeprom 0xf4)
tveeprom 2-0050: audio processor is CX882 (idx 33)
tveeprom 2-0050: decoder processor is CX882 (idx 25)
tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=69009
input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input3
cx88[0]/2: cx2388x 8802 Driver Manager
cx88[0]/2: found at 0000:04:08.2, rev: 5, irq: 21, latency: 32, mmio: 
0xf8000000
cx8802_probe() allocating 2 frontends
cx88[0]/0: found at 0000:04:08.0, rev: 5, irq: 21, latency: 32, mmio: 
0xfa000000
cx2388x alsa driver version 0.0.6 loaded
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 
DVB-S/S2/T/Hybrid [card=59]
cx88[0]/2: cx2388x based DVB/ATSC card
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
dvb: videobuf_dvb_register_adapter()
DVB: registering new adapter (cx88[0])
dvb: videobuf_dvb_register_adapter() returns 0
DVB: registering frontend 0 (Conexant CX22702 DVB-T)...
DVB: registering frontend 0 (Conexant CX24116/CX24118)...
cx24116_firmware_ondemand: Waiting for firmware upload 
(dvb-fe-cx24116.fw)...
cx24116_firmware_ondemand: Waiting for firmware upload(2)...
cx24116_load_firmware: FW version 1.20.79.0
cx24116_firmware_ondemand: Firmware upload complete


---------------------------------------------
media1:~# ls -la /dev/dvb/adapter0/
total 0
drwxr-xr-x 2 root root      200 2008-01-23 22:50 .
drwxr-xr-x 3 root root       60 2008-01-23 22:50 ..
crw-rw---- 1 root video 212,  4 2008-01-23 22:50 demux0
crw-rw---- 1 root video 212, 20 2008-01-23 22:50 demux1
crw-rw---- 1 root video 212,  5 2008-01-23 22:50 dvr0
crw-rw---- 1 root video 212, 21 2008-01-23 22:50 dvr1
crw-rw---- 1 root video 212,  3 2008-01-23 22:50 frontend0
crw-rw---- 1 root video 212, 19 2008-01-23 22:50 frontend1
crw-rw---- 1 root video 212,  7 2008-01-23 22:50 net0
crw-rw---- 1 root video 212, 23 2008-01-23 22:50 net1

I have nothing plugged into the cards at the moment but I can scan (and get 
nothing) both (but not at the same time).  In theory should the DVB-T and 
DVB-S be able to be used at the same time?? If this is all ok (when I get 
antenna/satellite dish on card) I just have to get the DVB-S2/multiproto 
working.

Thanks





More information about the linux-dvb mailing list