[linux-dvb] Fwd: Problem with Twinhan 102g not being recognized

Corey Ashford yeroca at yahoo.com
Tue Jan 29 04:48:14 CET 2008


I just now tried pulling the VP-3250 card, and the result is the same,
as you can see below:

...
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
wifi0: Atheros 5212: mem=0xfeae0000, irq=22
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:02:0b.0[A] -> GSI 23 (level, low) -> IRQ 16
bttv0: Bt878 (rev 17) at 0000:02:0b.0, irq: 16, latency: 32, mmio:
0xbfefc000
bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is
1822:0001
bttv0: using: Twinhan DST + clones [card=113,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00f500ff [init]
bttv0: tuner absent
bttv0: add subdevice "dvb0"
net wlan0: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface ath0 to wlan0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
NVRM: loading NVIDIA UNIX x86 Kernel Module  169.07  Thu Dec 13
18:42:56 PST 2007
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0b.1[A] -> GSI 23 (level, low) -> IRQ 16
bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB
functions.
bt878(0): Bt878 (rev 17) at 02:0b.1, irq: 16, latency: 32, memory:
0xbfefd000
DVB: registering new adapter (bttv0)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.5 to 64
dst(0) dst_get_device_id: Recognise [DST-03T]
dst(0) dst_get_device_id: Unsupported
dst(0) dst_get_device_id: Unsupported
dst(0) dst_get_device_id: [DST-03T] has a [MB 86A15]
dst(0) dst_get_device_id: [DST-03T] has a [MB 86A15]
DST type flags : 0x2 ts204 0x4 symdiv 0x10 firmware version = 2
dst(0) dst_get_mac: MAC Address=[00:08:ca:16:bc:00]
DVB: registering frontend 0 (DST DVB-S)...


I did remove the tuner "can" cover on the board, and found that this
card is indeed using an LG tuner.  There is about a 10-digit string of
numbers etched on the PC board in the tuner, but I didn't write it
down.  Somehow, it didn't look like a model number, but may have been.

I'm going to have a look at the code in dst to see if I can figure out
what the printk messages are telling me.

If you have any other ideas, please let me know.

Thanks for your time,

- Corey

--- CityK <CityK at rogers.com> wrote:

> Corey,
> 
> What happens if you pull the VP-3250 card out of the system -- any 
> change for the 102G or is it still the same result?
> 
> [ OT -- out of curiosity, are you just using the VP-3250 for OTA
> (8VSB)? 
> .... I ask because we have Zero known cases of success for digital
> cable 
> (QAM) with the card .... as it is, there is likely an inherent
> problem 
> (i.e. buggy embedded firmware being used by the card) that provides 
> reason or explanation for such observation, and this situation is 
> unlikely to have changed....but, it doesn't hurt to keep following up
> on 
> this, or obtain another data point.]
> 
> 
> 



      ____________________________________________________________________________________
Never miss a thing.  Make Yahoo your home page. 
http://www.yahoo.com/r/hs



More information about the linux-dvb mailing list