[linux-dvb] Support for Leadtek DTV1000S ?
damien at damienandlaurel.com
Fri Oct 3 05:12:19 CEST 2008
On Fri, Oct 3, 2008 at 9:14 AM, hermann pitton <hermann-pitton at arcor.de>wrote:
> Am Donnerstag, den 02.10.2008, 19:15 +0200 schrieb Matthias Schwarzott:
> > On Donnerstag, 2. Oktober 2008, Plantain wrote:
> > >
> > > Hey,
> > >
> > > I'm not actually able to code in C, but I've spent the last 24 hours
> > > puddling around trying to get somewhere. I believe I've added
> > > that is needed for the card to be detected, but it's not detecting it,
> > > even if I specify it with card=152 (the ID I've added). I have got the
> > > code to compile at least, which I'm pretty proud of :)
> > >
> > > I managed to get regspy to work (needed to revert 64bit vista to 32bit
> > > XP), but the viewing software that came with the card just crashes on
> > > 32bit XP. I've built a small wiki page (with highres images) detailing
> > > my progress, but I've really just hit a brick wall. Wikipage at
> > > http://www.linuxtv.org/wiki/index.php/WinFast_DTV_1000_S
> > >
> > > Short of learning C (which I am very slowly doing), I don't see anyway
> > > forwards under my direction, so I've attached my efforts in the hope
> > > someone else can take this forwards. From my limited understanding I've
> > > provided all the necessary information for someone to finish it, and if
> > > not I'll happily dig up anything else needed. I'm not familiar with any
> > > version control system/patching, so I've just hg diff > file.diff, I
> > > hope this is adequate.
> > >
> > > I'm on #linuxtv @ freenode IRC for a significant portion of the day if
> > > anyone has pointers for me/wants to ask questions about the card.
> > >
> > Looking at your regspy output
> > 109. SAA7134_GPIO_GPMODE: 82000000 (10000010 00000000
> > 00000000 00000000)
> > 110. SAA7134_GPIO_GPSTATUS: 02132054 (00000010 00010011
> > 00100000 01010100)
> > I suggest you change your gpio code like this:
> > saa_andorl(SAA7134_GPIO_GPMODE0 >> 2, 0x82000000,
> > 0x82000000);
> > saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, 0x02000000,
> > 0x02000000);
> > So this at least sets the directions of gpios as used in windows, and
> > the same values on the gpios configured as output. That should work
> > than your copy-and-pasted numbers from another card.
> > But it still can be you need to pull some pins high or low for some time
> > init to get parts reset.
> > You also could try adding a small wait time after writing gpio values.
> > e.g. msleep(500);
> > Good luck
> > Matthias
> yes, that is likely the most solid start we can have from the analog
> side so far. The card should be auto detectable as well.
> linux-dvb mailing list
> linux-dvb at linuxtv.org
I have a 64 bit system and am farmiliar with C/C++/etc, but not so farmiliar
with the specific code yet. I have one of these cards and am willing to put
a bit of work into getting it going. How can I be of use?
-------------- next part --------------
An HTML attachment was scrubbed...
More information about the linux-dvb