[vdr] New Nexus FF Ver 2.3 cards

Martin Spears martin at kober.net
Wed Mar 23 20:24:07 CET 2005


here is my diseqc.conf

# DiSEqC configuration for VDR
#
# Format:
#
# satellite slof polarization lof command...
#
# satellite:      one of the 'S' codes defined in sources.conf
# slof:           switch frequency of LNB; the first entry with
#                 an slof greater than the actual transponder
#                 frequency will be used
# polarization:   V = vertical, H = horizontal
# lof:            the local oscillator frequency to subtract from
#                 the actual transponder frequency
# command:
#   t         tone off
#   T         tone on
#   v         voltage low (13V)
#   V         voltage high (18V)
#   A         mini A
#   B         mini B
#   Wnn       wait nn milliseconds (nn may be any positive integer number)
#   [xx ...]  hex code sequence (max. 6)
#
# The 'command...' part is optional.
#
# Examples:

# Full DiSEqC sequence:

S119W  11250 V 99999  t v W15 [E0 10 38 F0] W15 A W15 t
S119W  99999 V 11250  t v W15 [E0 10 38 F1] W15 A W15 T
S119W  11250 H 99999  t V W15 [E0 10 38 F2] W15 A W15 t
S119W  99999 H 11250  t V W15 [E0 10 38 F3] W15 A W15 T

S110W  11250 V 99999  t v W15 [E0 10 38 F4] W15 B W15 t
S110W  99999 V 11250  t v W15 [E0 10 38 F5] W15 B W15 T
S110W  11250 H 99999  t V W15 [E0 10 38 F6] W15 B W15 t
S110W  99999 H 11250  t V W15 [E0 10 38 F7] W15 B W15 T

and what happens when I cahnge channels


softcam 0: setting new SID 118, source 84a6, transponder 33e06
softcam 0: logger stopped
ecmcache: from cache: system Nagra (1800) id 0000 with ecm 24
softcam 0: try system Nagra (1800) id 0000 with ecm 24 (cached) (pri=-10)
softcam 0: started logger sys=0x1800 id=0x0
system: using key N 101 00 B3E1DF3753758AB5
softcam 0: correct key found
softcam 0: started logger sys=0x1800 id=0x0
softcam 0: check ProvidesCa: 1810 1801 1800 -> n=1
softcam 0: ignoring new SID 118, source 84a6, transponder 33e06
softcam 0: check ProvidesCa: 1810 1801 1800 -> n=1
softcam 0: setting new SID 506, source 844c, transponder 33e98
softcam 0: logger stopped
ecmcache: from cache: system Nagra (1800) id 0000 with ecm 26
softcam 0: try system Nagra (1800) id 0000 with ecm 26 (cached) (pri=-10)
softcam 0: started logger sys=0x1800 id=0x0
system: using key N 101 00 B3E1DF3753758AB5
softcam 0: correct key found
softcam 0: started logger sys=0x1800 id=0x0

but when I change channels to this other sat, there is nothing but a blank
screen. if I disconnect the switch and go direct then the system works
perfect
this happens with both vdr 1.3.22 and 1.3.23

any ideas

-----Original Message-----
From: vdr-bounces at linuxtv.org [mailto:vdr-bounces at linuxtv.org]On Behalf Of
Oliver Endriss
Sent: Monday, March 21, 2005 5:28 PM
To: vdr at linuxtv.org
Subject: Re: [vdr] New Nexus FF Ver 2.3 cards


Martin Spears wrote:
> without the use of diseqc the card does work. I can recieve from several
> sats as long as I do not use diseqc switching. If I were to go direct then
> everything works perfect.

Ok, let's assume that the DiSEqC code in the stv0299 driver is buggy.
Try the attached patch. Does it work now?

If not, try to load the stv0299 driver with parameter 'debug=1' and post
the output when tuning. Please post your diseqc.conf file.

Oliver

--
--------------------------------------------------------
VDR Remote Plugin available at
http://www.escape-edv.de/endriss/vdr/
--------------------------------------------------------

--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.7.4 - Release Date: 3/18/2005

--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.8.0 - Release Date: 3/21/2005




More information about the vdr mailing list