[vdr] VDR 1.7.0 - Patched for S2-3200 - Diseqc.conf

[Jelle De Loecker]

Jelle De Loecker schreef:
> I've finally gotten VDR to work with my Technotrend S2-3200 card, but I 
> just can't seem to get this diseqc.conf file right!
>
>  S19.2E  11700 V  9750  [E0 10 38 F0]
>  S19.2E  99999 V 10600  [E0 10 38 F1]
>  S19.2E  11700 H  9750  [E0 10 38 F2]
>  S19.2E  99999 H 10600  [E0 10 38 F3]
>
>  S28.2E  11700 V  9750  [E0 10 38 F4]
>  S28.2E  99999 V 10600  [E0 10 38 F5]
>  S28.2E  11700 H  9750  [E0 10 38 F6]
>  S28.2E  99999 H 10600  [E0 10 38 F7]
>
> I have a diseqc 2.0 switch, but since the S2-3200 card only supports 
> Diseqc 1.2 I'm not really sure what to use!
> It's a regular 4x1 switch
>   
Apparantly a regular 4x1 switch doesn't need the "F0 - F1" bits at the 
end, and this will do.
As I see it, the first hex-code is used for the option and the second 
hex-code is used for the position. (A/A-A/B-B/A-B/B)

22 Position A
23 Option A
26 Position B
27 Option B

# port 1 option a position a
# port 2 option a position b
# port 3 option b position a
# port 4 option b position b

So in your setup I assume that you have ports and LNBs like this:

1 - S19.2E
2 - S28.2E
3 - S23.5E
4 - S13.0E

This diseqc.conf should do the trick:

# port 1
S19.2E  11700 V  9750  t v W15 [E0 10 23] W15 [E0 10 22] W15 t
S19.2E  99999 V 10600  t v W15 [E0 10 23] W15 [E0 10 22] W15 T
S19.2E  11700 H  9750  t V W15 [E0 10 23] W15 [E0 10 22] W15 t
S19.2E  99999 H 10600  t V W15 [E0 10 23] W15 [E0 10 22] W15 T

# port 2
S28.2E  11700 V  9750  t v W15 [E0 10 23] W15 [E0 10 26] W15 t
S28.2E  99999 V 10600  t v W15 [E0 10 23] W15 [E0 10 26] W15 T
S28.2E  11700 H  9750  t V W15 [E0 10 23] W15 [E0 10 26] W15 t
S28.2E  99999 H 10600  t V W15 [E0 10 23] W15 [E0 10 26] W15 T

# port 3
S23.5E  11700 V  9750  t v W15 [E0 10 27] W15 [E0 10 22] W15 t
S23.5E  99999 V 10600  t v W15 [E0 10 27] W15 [E0 10 22] W15 T
S23.5E  11700 H  9750  t V W15 [E0 10 27] W15 [E0 10 22] W15 t
S23.5E  99999 H 10600  t V W15 [E0 10 27] W15 [E0 10 22] W15 T

# port 4
S13.0E  11700 V  9750  t v W15 [E0 10 27] W15 [E0 10 26] W15 t
S13.0E  99999 V 10600  t v W15 [E0 10 27] W15 [E0 10 26] W15 T
S13.0E  11700 H  9750  t V W15 [E0 10 27] W15 [E0 10 26] W15 t
S13.0E  99999 H 10600  t V W15 [E0 10 27] W15 [E0 10 26] W15 T

Should you need to edit the first port

I got this solution from the archive from these very own mailing lists, 
but it was very hard to find so I thought I'd post it again. It works 
like a charm:
http://www.linuxtv.org/pipermail/vdr/2005-October/005517.html (thank you 
*Sami J. Mäkinen)*