AVerMedia Cardbus E500 - Revision history

Jimbley: Added category:Analog CardBus devices

2009-05-06T22:32:29Z

Added category:Analog CardBus devices

← Older revision		Revision as of 22:32, 6 May 2009
Line 117:		Line 117:
	It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).		It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).
	//jostmart		//jostmart
		+	[[Category:Analog CardBus Devices]]

CityK: 10 revision(s)

2008-10-30T02:27:37Z

10 revision(s)

← Older revision

Revision as of 02:27, 30 October 2008

Js: Reverted edits by BpgTxl (Talk); changed back to last version by Js

2007-06-24T08:31:40Z

Reverted edits by BpgTxl (Talk); changed back to last version by Js

← Older revision		Revision as of 08:31, 24 June 2007
Line 7:		Line 7:
	To make is work, I did the following:		To make is work, I did the following:

-	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290 75.	+	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290+75.

	2. In saa7134-cards.c I replaced the the board config entry for this card with the following:		2. In saa7134-cards.c I replaced the the board config entry for this card with the following:
Line 60:		Line 60:
	Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff		Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff
	Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])		Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])
-	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290 75	+	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290+75
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Line 94:		Line 94:
	After compiling and loading the module saa7134, the commands:		After compiling and loading the module saa7134, the commands:

-	tvtime --mixer=/dev/mixer:vol	+	tvtime --mixer=/dev/mixer:vol&
		+	sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -w -r 32000 /dev/dsp &
		+
		+	starts tvtime with sound and sound is now restored when changing channels.
		+
		+	The only flaw left is that, when changing channel, during ~1 sec. sound of the new channel is heard, followed by ~1 sec. of noise, whereafter sound is restored properly.
		+
		+	6. Problems left
		+
		+	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?
		+	* so far, I haven't tested the S-Video and Composite inputs of this card.
		+	'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option
		+	modprobe saa7134 card=46 oss=1
		+	because the card type was not auto detected.
		+
		+
		+	This was done on a Dell Inspiron 4150 with Fedora Core 3 Installed.
		+
		+	-------
		+	Kees Blom
		+
		+	It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).
		+	//jostmart

BpgTxl at 01:58, 24 June 2007

2007-06-24T01:58:03Z

← Older revision		Revision as of 01:58, 24 June 2007
Line 7:		Line 7:
	To make is work, I did the following:		To make is work, I did the following:

-	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290+75.	+	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290 75.

	2. In saa7134-cards.c I replaced the the board config entry for this card with the following:		2. In saa7134-cards.c I replaced the the board config entry for this card with the following:
Line 60:		Line 60:
	Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff		Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff
	Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])		Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])
-	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290+75	+	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290 75
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Line 94:		Line 94:
	After compiling and loading the module saa7134, the commands:		After compiling and loading the module saa7134, the commands:

-	tvtime --mixer=/dev/mixer:vol&	+	tvtime --mixer=/dev/mixer:vol
-	~~sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -w -r 32000 /dev/dsp &~~	+
-		+
-	~~starts tvtime with sound and sound is now restored when changing channels.~~	+
-		+
-	~~The only flaw left is that, when changing channel, during ~1 sec. sound of the new channel is heard, followed by ~1 sec. of noise, whereafter sound is restored properly.~~	+
-		+
-	~~6. Problems left~~	+
-		+
-	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?	+
-	* so far, I haven't tested the S-Video and Composite inputs of this card.	+
-	~~'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option~~	+
-	~~modprobe saa7134 card=46 oss=1~~	+
-	~~because the card type was not auto detected.~~	+
-		+
-		+
-	~~This was done on a Dell Inspiron 4150 with Fedora Core 3 Installed.~~	+
-		+
-	~~-------~~	+
-	~~Kees Blom~~	+
-		+
-	~~It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).~~	+
-	~~//jostmart~~	+

Js: Reverted edits by AnsMhb (Talk); changed back to last version by Js

2007-06-23T22:26:46Z

Reverted edits by AnsMhb (Talk); changed back to last version by Js

← Older revision		Revision as of 22:26, 23 June 2007
Line 7:		Line 7:
	To make is work, I did the following:		To make is work, I did the following:

-	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290 75.	+	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290+75.

	2. In saa7134-cards.c I replaced the the board config entry for this card with the following:		2. In saa7134-cards.c I replaced the the board config entry for this card with the following:
Line 60:		Line 60:
	Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff		Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff
	Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])		Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])
-	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290 75	+	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290+75
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Line 94:		Line 94:
	After compiling and loading the module saa7134, the commands:		After compiling and loading the module saa7134, the commands:

-	tvtime --mixer=/dev/mixer:vol	+	tvtime --mixer=/dev/mixer:vol&
		+	sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -w -r 32000 /dev/dsp &
		+
		+	starts tvtime with sound and sound is now restored when changing channels.
		+
		+	The only flaw left is that, when changing channel, during ~1 sec. sound of the new channel is heard, followed by ~1 sec. of noise, whereafter sound is restored properly.
		+
		+	6. Problems left
		+
		+	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?
		+	* so far, I haven't tested the S-Video and Composite inputs of this card.
		+	'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option
		+	modprobe saa7134 card=46 oss=1
		+	because the card type was not auto detected.
		+
		+
		+	This was done on a Dell Inspiron 4150 with Fedora Core 3 Installed.
		+
		+	-------
		+	Kees Blom
		+
		+	It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).
		+	//jostmart

AnsMhb at 21:16, 23 June 2007

2007-06-23T21:16:57Z

← Older revision		Revision as of 21:16, 23 June 2007
Line 7:		Line 7:
	To make is work, I did the following:		To make is work, I did the following:

-	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290+75.	+	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290 75.

	2. In saa7134-cards.c I replaced the the board config entry for this card with the following:		2. In saa7134-cards.c I replaced the the board config entry for this card with the following:
Line 60:		Line 60:
	Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff		Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff
	Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])		Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])
-	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290+75	+	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290 75
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Line 94:		Line 94:
	After compiling and loading the module saa7134, the commands:		After compiling and loading the module saa7134, the commands:

-	tvtime --mixer=/dev/mixer:vol&	+	tvtime --mixer=/dev/mixer:vol
-	~~sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -w -r 32000 /dev/dsp &~~	+
-		+
-	~~starts tvtime with sound and sound is now restored when changing channels.~~	+
-		+
-	~~The only flaw left is that, when changing channel, during ~1 sec. sound of the new channel is heard, followed by ~1 sec. of noise, whereafter sound is restored properly.~~	+
-		+
-	~~6. Problems left~~	+
-		+
-	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?	+
-	* so far, I haven't tested the S-Video and Composite inputs of this card.	+
-	~~'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option~~	+
-	~~modprobe saa7134 card=46 oss=1~~	+
-	~~because the card type was not auto detected.~~	+
-		+
-		+
-	~~This was done on a Dell Inspiron 4150 with Fedora Core 3 Installed.~~	+
-		+
-	~~-------~~	+
-	~~Kees Blom~~	+
-		+
-	~~It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).~~	+
-	~~//jostmart~~	+

Js: Reverted edits by IxgC7x (Talk); changed back to last version by Segfault

2007-04-18T19:00:31Z

Reverted edits by IxgC7x (Talk); changed back to last version by Segfault

← Older revision		Revision as of 19:00, 18 April 2007
Line 7:		Line 7:
	To make is work, I did the following:		To make is work, I did the following:

-	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290 75.	+	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290+75.

	2. In saa7134-cards.c I replaced the the board config entry for this card with the following:		2. In saa7134-cards.c I replaced the the board config entry for this card with the following:
Line 60:		Line 60:
	Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff		Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff
	Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])		Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])
-	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290 75	+	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290+75
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Line 94:		Line 94:
	After compiling and loading the module saa7134, the commands:		After compiling and loading the module saa7134, the commands:

-	tvtime --mixer=/dev/mixer:vol	+	tvtime --mixer=/dev/mixer:vol&
		+	sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -w -r 32000 /dev/dsp &
		+
		+	starts tvtime with sound and sound is now restored when changing channels.
		+
		+	The only flaw left is that, when changing channel, during ~1 sec. sound of the new channel is heard, followed by ~1 sec. of noise, whereafter sound is restored properly.
		+
		+	6. Problems left
		+
		+	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?
		+	* so far, I haven't tested the S-Video and Composite inputs of this card.
		+	'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option
		+	modprobe saa7134 card=46 oss=1
		+	because the card type was not auto detected.
		+
		+
		+	This was done on a Dell Inspiron 4150 with Fedora Core 3 Installed.
		+
		+	-------
		+	Kees Blom
		+
		+	It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).
		+	//jostmart

IxgC7x at 18:01, 18 April 2007

2007-04-18T18:01:56Z

← Older revision		Revision as of 18:01, 18 April 2007
Line 7:		Line 7:
	To make is work, I did the following:		To make is work, I did the following:

-	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290+75.	+	1. Got the (almost) latest kernel from www.kernel.org (2.6.12-rc1) with support for tda8290 75.

	2. In saa7134-cards.c I replaced the the board config entry for this card with the following:		2. In saa7134-cards.c I replaced the the board config entry for this card with the following:
Line 60:		Line 60:
	Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff		Mar 28 21:57:55 localhost kernel: saa7134[0]: board init: gpio is effffff
	Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])		Mar 28 21:57:56 localhost kernel: tuner 0-004b: chip found @ 0x96 (saa7134[0])
-	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290+75	+	Mar 28 21:57:56 localhost kernel: tuner 0-004b: tuner: type set to tda8290 75
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 00: 61 14 ee d6 ff ff ff ff ff ff ff ff ff ff ff ff
	Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff		Mar 28 21:57:56 localhost kernel: saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Line 94:		Line 94:
	After compiling and loading the module saa7134, the commands:		After compiling and loading the module saa7134, the commands:

-	tvtime --mixer=/dev/mixer:vol&	+	tvtime --mixer=/dev/mixer:vol
-	~~sox -c 2 -s -w -r 32000 -t ossdsp /dev/dsp2 -t ossdsp -w -r 32000 /dev/dsp &~~	+
-		+
-	~~starts tvtime with sound and sound is now restored when changing channels.~~	+
-		+
-	~~The only flaw left is that, when changing channel, during ~1 sec. sound of the new channel is heard, followed by ~1 sec. of noise, whereafter sound is restored properly.~~	+
-		+
-	~~6. Problems left~~	+
-		+
-	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?	+
-	* so far, I haven't tested the S-Video and Composite inputs of this card.	+
-	~~'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option~~	+
-	~~modprobe saa7134 card=46 oss=1~~	+
-	~~because the card type was not auto detected.~~	+
-		+
-		+
-	~~This was done on a Dell Inspiron 4150 with Fedora Core 3 Installed.~~	+
-		+
-	~~-------~~	+
-	~~Kees Blom~~	+
-		+
-	~~It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).~~	+
-	~~//jostmart~~	+

Segfault at 14:06, 28 May 2006

2006-05-28T14:06:05Z

← Older revision		Revision as of 14:06, 28 May 2006
Line 114:		Line 114:
	-------		-------
	Kees Blom		Kees Blom
		+
		+	It looks like that all the source changes are in the 2.6.15 kernel (and probably som lower versions).
		+	//jostmart

Mcoates at 17:14, 16 August 2005

2005-08-16T17:14:11Z

← Older revision		Revision as of 17:14, 16 August 2005
Line 105:		Line 105:
	* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?		* is the code to wake up the tuner chip correct? Isn't trying to set all bits high a little bit too much?
	* so far, I haven't tested the S-Video and Composite inputs of this card.		* so far, I haven't tested the S-Video and Composite inputs of this card.
-	Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option	+	'''Edit:'''Both S-Video and Composite inputs work fine, even before changes to saa7134-cards.c. I needed to pass the module option
	modprobe saa7134 card=46 oss=1		modprobe saa7134 card=46 oss=1
	because the card type was not auto detected.		because the card type was not auto detected.