Hauppauge WinTV Go: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
m (WinTV Go moved to Hauppauge WinTV Go: name)
m (fixed link)
Line 12: Line 12:
modprobe cx88xx tuner=56 && modprobe cx8800
modprobe cx88xx tuner=56 && modprobe cx8800


Tuner 56 is the Philips PAL/SECAM multi (FQ1216AME MK4). You may need a different one; see [[Tuners]].
Tuner 56 is the Philips PAL/SECAM multi (FQ1216AME MK4). You may need a different one; see "[[Tuners: Supported Tuners|Supported Tuners]]".


====WinTV Go2====
====WinTV Go2====

Revision as of 19:05, 11 January 2008

These cards are based on the cx88 chip.

WinTV Go

The WinTV Go card shows up in lspci as:

Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
Subsystem: Hauppauge computer works Inc. Hauppauge WinTV 34xxx models

Load the driver as follows:

modprobe cx88xx tuner=56 && modprobe cx8800

Tuner 56 is the Philips PAL/SECAM multi (FQ1216AME MK4). You may need a different one; see "Supported Tuners".

WinTV Go2

The WinTV Go2 card shows up in lspci-v as:

Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)

lspci -n:

 00:00.0 0600: 8086:2770 (rev 02)
 00:01.0 0604: 8086:2771 (rev 02)
 00:1b.0 0403: 8086:27d8 (rev 01)
 00:1c.0 0604: 8086:27d0 (rev 01)
 00:1c.2 0604: 8086:27d4 (rev 01)
 00:1d.0 0c03: 8086:27c8 (rev 01)
 00:1d.1 0c03: 8086:27c9 (rev 01)
 00:1d.2 0c03: 8086:27ca (rev 01)
 00:1d.3 0c03: 8086:27cb (rev 01)
 00:1d.7 0c03: 8086:27cc (rev 01)
 00:1e.0 0604: 8086:244e (rev e1)
 00:1f.0 0601: 8086:27b8 (rev 01)
 00:1f.2 0101: 8086:27c0 (rev 01)
 00:1f.3 0c05: 8086:27da (rev 01)
 01:00.0 0300: 10de:01df (rev a1)
 03:00.0 0200: 10ec:8168 (rev 01)
 04:01.0 0400: 14f1:8800 (rev 05)
 04:01.1 0480: 14f1:8811 (rev 05)

portions of /var/log/message:

CORE cx88[0]: subsystem: 0070:3401, board: Hauppauge WinTV 34xxx models [card=1,autodetected]
TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe
cx2388x alsa driver version 0.0.6 loaded
i2c-algo-bit.o: cx88[0] passed test.
tveeprom 0-0050: Hauppauge model 34704, rev J1B3, serial# 8521833
tveeprom 0-0050: tuner model is TCL M2523_3DB_E (idx 113, type 55)
tveeprom 0-0050: TV standards PAL(B/G) PAL(D/D1/K) (eeprom 0x44)
tveeprom 0-0050: audio processor is CX881 (idx 31)
tveeprom 0-0050: has radio
cx88[0]: warning: unknown hauppauge model #34704
cx88[0]: hauppauge eeprom: model=34704
Input: cx88 IR (Hauppauge WinTV 34xxx  as /class/input/input3
cx88[0]/0: found at 0000:04:01.0, rev: 5, irq: 217, latency: 32, mmio: 0xe5000000
tuner 0-0061: chip found @ 0xc2 (cx88[0])
tuner 0-0061: type set to 55 (TCL 2002MB)
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0

This must be a new WinTV Go2 Model, so with the current (November 2006) v4l-dvb tree (hg) it's autodected, even if /var/log/message says:

CORE cx88[0]: subsystem: 0070:3401, board: Hauppauge WinTV 34xxx models [card=1,autodetected]
TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe

if you go a bit down in my /var/log/message (shown above) you can see a line like this:

tuner 0-0061: type set to 55 (TCL 2002MB)

Contributed by scto and copied from Cx88 devices (cx2388x).