Leadtek WinFast 2000: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
(tuner=38 for a card bought in Austria)
 
Line 60: Line 60:
|-
|-
| 2 || NTSC || United States
| 2 || NTSC || United States
|-
| 3 || SECAM+PAL_BG || France
|-
|-
| 24 || PAL/SECAM multi || South Africa
| 24 || PAL/SECAM multi || South Africa

Revision as of 19:53, 30 October 2005

Introduction

Card 34 in the bttv cardlist works for a variety of Leadtek cards, including the Winfast 2000, Winfast TV2000 XP, Winfast TV2000 XP RM and Winfast TV2000 XP FM. Most of them also have an IR remote built in.

Installing the card

This card shows up on the PCI bus as two devices, one for video capture and one for audio:

lspci:

0000:01:06.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:01:06.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)

lspci -vn:

0000:01:06.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
       Subsystem: LeadTek Research Inc.: Unknown device 6609
       Flags: bus master, medium devsel, latency 32, IRQ 12
       Memory at de000000 (32-bit, prefetchable)
       Capabilities: [44] Vital Product Data
       Capabilities: [4c] Power Management version 2
0000:01:06.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
       Subsystem: LeadTek Research Inc.: Unknown device 6609
       Flags: bus master, medium devsel, latency 32, IRQ 12
       Memory at de001000 (32-bit, prefetchable)
       Capabilities: [44] Vital Product Data
       Capabilities: [4c] Power Management version 2

The card is recognized when the bttv module is loaded on boot; here's a typical dmesg log:

bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 5
ACPI: PCI interrupt 0000:01:06.0[A] -> GSI 5 (level, low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:01:06.0, irq: 5, latency: 32, mmio: 0xde000000
bttv0: detected: Leadtek TV 2000 XP [card=34], PCI subsystem ID is 107d:6609
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,autodetected]
bttv0: using tuner=24
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 24 (Philips PAL/SECAM multi (FQ1216ME)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "remote0"
ir-kbd-gpio: bttv IR (card=34) detected at pci-0000:01:06.0/ir0

The second tuner line can also appear as one of:

tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) by bt878 #0 [sw]
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by bt878 #0 [sw]

Tuner Types

Number Type Countries
2 NTSC United States
3 SECAM+PAL_BG France
24 PAL/SECAM multi South Africa
38 PAL Austria

Getting the sound from the sound card

It is unknown if the btaudio module works with this card. A patch cable from the tv card to the sound card does work. A patch cable from the tv card to the motherboard CD-in also works for those with onboard sound cards.

Setting up the remote