TerraTec Cinergy C DVB-C
This Article is a Stub or is Incomplete
This article, or sections contained within it, requires expansion. Help is needed to make this article more informative.
Drivers: work in progress; see below
Looks to be a clone of the Azurewave/Twinhan AD-CP400 (VP-2040) 
- NXP/Philips CU1216 module
- NXP/Philips TDA10023 (demodulator)
- Mantis (bridge)
$ lspci -v -s 01:01.0 01:01.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV PCI Bridge Controller [Ver 1.0] (rev 01) Subsystem: TERRATEC Electronic GmbH Unknown device 1178 Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at cfdff000 (32-bit, prefetchable) [size=4K]
$ lspci -vvn -s 01:01.0 01:01.0 0480: 1822:4e35 (rev 01) Subsystem: 153b:1178 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 63750ns max) Interrupt: pin A routed to IRQ 22 Region 0: Memory at cfdff000 (32-bit, prefetchable) [size=4K]
Making it Work
No firmware required.
Installing the driver
Kernel 2.6.28 released on 24.12.2008 works with the mantis driver in the s2-liplianin repository.
The mantis-multiproto driver has been tested with Ubuntu Hardy (2.6.24?) on the 28.11.2008. CAM/CI is not working with current mantis for me. I have a crash when scanning or zapping with the CAM inserted. Take the CAM module out if you have one for the moment! (Is this also true for the new driver??)
Install mantis driver
Recommended: install the latest mantis drivers like this.
sudo apt-get install mercurial hg clone http://mercurial.intuxication.org/hg/s2-liplianin cd s2-liplianin make sudo make install sudo reboot
Old mantis-multiproto repository intstructions. May not compile with latest kernels.
cd /usr/src sudo apt-get install mercurial sudo hg clone http://jusst.de/hg/mantis cd mantis sudo make sudo make install sudo reboot
Sample kernel output
With latest build from http://jusst.de/hg/mantis:
[ 47.563542] found a VP-2040 PCI DVB-C device on (01:01.0), [ 47.563543] Mantis Rev 1 [153b:1178], irq: 22, latency: 64 [ 47.563545] memory: 0xcfdff000, mmio: 0xf89de000 [ 47.566227] MAC Address=[00:08:ca:1c:73:1d] [ 47.566254] mantis_alloc_buffers (0): DMA=0x37850000 cpu=0xf7850000 size=65536 [ 47.566292] mantis_alloc_buffers (0): RISC=0x37913000 cpu=0xf7913000 size=1000 [ 47.566332] DVB: registering new adapter (Mantis dvb adapter) [ 48.086203] mantis_frontend_init (0): Probing for CU1216 (DVB-C) [ 48.088334] mantis_frontend_init (0): found Philips CU1216 DVB-C frontend 0x0c [ 48.088378] mantis_frontend_init (0): Mantis DVB-C Philips CU1216 frontend attach success [ 48.088424] DVB: registering frontend 0 (Philips TDA10023 DVB-C)... [ 54.367799] mantis_ack_wait (0): Slave RACK Fail !
Remote Control Support
For the old driver (Manu's) RC works after applying the following patch. See 
NOTE: I wonder why this patch has not been merged into the trunk. Does it break anything?
Regarding the new driver. I think the remote is supported already out-of-the box. Can anybody confirm that?
Unfortunately that doesn't seem to be the case, at least in my box running 2.6.27 (Ubuntu 8.10 stock kernel) the remote does not seem to work with the new driver (894056bee8c1), and the patch doesn't work with it, either. (Otherwise the card works fine.)
CI/CAM support for the optional CI module is not working yet (8.03.2014)
Working around i2c bus probing interference with ivtv
If the mantis module won't load (hangs) with the error message
mantis_ack_wait (0): Slave RACK Fail !
you should check []