Mailing List archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

syncrange listing?



I'm now getting this for a sync... does anyone have a list of sync numbers
and their meanings?

Fsync = 0, Freq = 2033000000, Sync = 0 Afc = 4292904796 Agc = 159 Nest =
49152 Vber = 165672

cheers,
Robin
----- Original Message -----
From: "Uwe Guenther" <uwe@cscc.de>
To: "Robin Edgar Tripany" <red@tripany.com>
Sent: Friday, October 13, 2000 1:33 AM
Subject: Re: Routing Probs with dvb0


> Robin Edgar Tripany wrote:
> >
> > K...... got dvbd drivers compiled, installed and they work :)
> >
> > got dvbd compiled and dvbd.conf editted to my specific settings....
> > my primary questions are:
> >
> > 1. When i run dvbd without the -q option i get these lines over and over
> > again:
> >
> >     "VFsync = 0, Freq = 2033000000, Sync = 3 Afc = 4293076671 Agc = 319
Nest
> > = 43264"
> >     "VFsync = 0, Freq = 2033000000, Sync = 3 Afc = 4293076671 Agc = 303
Nest
> > = 43776"
> sync=3 means bad signal
>
> you should get sync=127
>
> >
> >     is this ok?
> > 2. How many filters do i need in /etc/dvbd.conf?
> >     (under windows i have 5!!!!)
> i have 2
> > 3. how do you set a MAC address on your card?
> > 4. as i understand you have to use mrouted to multicast your streams,
> >     what are the tunnel settings? (local ip = my uplink device?
remote=???)
> >     might you have your mrouted.conf file?
> >      I dont really understand the mrouted.conf file :)))
> >
> >     "phyint dvb0 altnet 212.17.1.212/1 altnet 125.0.0.0/1"
> >     "phyint eth0"
> >
> >     is the first altnet my ppp device and the second one the destination
> > address?
>  I don`t use mrouted
>
> I don´t understand this stuff too :))
>
> >
> > well, i hope someone can help me :)
> >
> > thanx
> >
> > robin
> >
> > ----- Original Message -----
> > From: "Uwe Guenther" <uwe@cscc.de>
> > To: "Robin Edgar Tripany" <red@tripany.com>
> > Sent: Thursday, October 05, 2000 5:28 PM
> > Subject: Re: Routing Probs with dvb0
> >
> > > Robin Edgar Tripany wrote:
> > > >
> > > > What did you use to get EON working?! where can i find the sources?
> > > >
> > >
> > > http://www.linuxtv.org/download/dvb/siemens_dvb-0.7.1.tar.gz
> > > http://www.linuxtv.org/download/dvb/dvbd2.tar.gz
> > >
> > >  and you could check my config, they is located at
> > >
> > > http://www.cscc.de/eon.tar.gz
> > >
> > >
> > > ... may the Tux be with you! =Uwe=
> > > --
> > > Uwe Günther                    \\://
mailto:uwe@cscc.de
> > > Haupstraße 88                  (o -)
http://www.cscc.de
> > > 98631 Behrungen          ---ooO-(_)-Ooo---
tel.:+49.36944.54448
> > > Germany                                       Linux, enjoy the ride
...!
> > >
>
> --
> ... may the Tux be with you! =Uwe=
> --
> Uwe Günther                    \\://                  mailto:uwe@cscc.de
> Haupstraße 88                  (o -)                  http://www.cscc.de
> 98631 Behrungen          ---ooO-(_)-Ooo---          tel.:+49.36944.54448
> Germany                                       Linux, enjoy the ride ...!
>



Home | Main Index | Thread Index