[vdr] Re: CA-Modul is not detectet by vdr-1.0.0 with AIO-Patch

["Andreas Grapp" <andreas.grapp@epost.de>]

Hi Stefan,

did you buy the new Hauppauge 3,5" Common Interface?
Take up the case and take a look at the Rev.-Number on the Board.
If it's Rev. 1.6 then the Interface is not supported by the driver/firmware
(I had the same problem).
The old ones (Rev. 1.4) work fine, but the new one (Rev. 1.6) does not work.
With the original Hauppauge-Software everything is fine.

Andreas

----- Original Message -----
From: "Stefan Lang" <steven@organet.com>
Newsgroups: boerde.lists.vdr
Sent: Thursday, April 18, 2002 9:00 AM
Subject: [vdr] CA-Modul is not detectet by vdr-1.0.0 with AIO-Patch


> Hello List,
>
> last version I used was 0.98 with patch... no problems with the CAM!
>
> Now I have upgraded my hardware and also vdr to version 1.0.0 with
> AIO-patch.
>
> After doing the obliged RTFM, I configured my system... free-to-air runs
> fine, but PW with irdeto 4.7se ... no go...the screen stays black!
> There is no message in /var/log/messages when I remove or insert the
> CA-Modul... in 0.98 there came up a message in syslog!
>
> I'm using _one_ hauppauge dvb-s with CI-Card in 3,5"-Floppy-format
> BTW What's about using the CI-card infrared-sensor with lirc??....
> I know: slightly off topic
>
> Kernel is 2.4.18 witch ACL-Patches.
>
> Okay here is my config:
>
> ca.conf
> #----------------------------------------------------------------
> # Conditional Access configuration for VDR
> #
> # Format:
> #
> # number  description
> #
> # Please contact kls@cadsoft.de before assigning a new number
> # to a description, in order to keep them unique.
>
> 0      Free To Air
>
> # BetaCrypt
>
> 101    Premiere World
> 102    ORF
>
> # Cryptoworks
>
> 201    GOD-DIGITAL
>
> # Special values to "hard code" a channel to a specific DVB card:
>
> 1      DVB 1
> 2      DVB 2
> 3      DVB 3
> 4      DVB 4
> #----------------------------------------------------------------
>
>
> channels.conf (one channel only)
> #----------------------------------------------------------------
> Premiere 1:11797:h:0:27500:511:512:0:101:10
> #----------------------------------------------------------------
>
> setup.conf
> #----------------------------------------------------------------
> # VDR Setup
> OSDLanguage        = 1
> PrimaryDVB         = 1
> ShowInfoOnChSwitch = 1
> MenuScrollPage     = 1
> MarkInstantRecord  = 1
> NameInstantRecord  = TITLE EPISODE
> LnbSLOF            = 11700
> LnbFrequLo         = 9750
> LnbFrequHi         = 10600
> DiSEqC             = 0
> SetSystemTime      = 1
> TimeTransponder    = 0
> MarginStart        = 2
> MarginStop         = 5
> EPGScanTimeout     = 5
> EPGBugfixLevel     = 2
> SVDRPTimeout       = 300
> SortTimers         = 1
> PrimaryLimit       = 0
> DefaultPriority    = 50
> DefaultLifetime    = 50
> UseSubtitle        = 1
> RecordingDirs      = 1
> VideoFormat        = 0
> RecordDolbyDigital = 1
> ChannelInfoPos     = 0
> OSDwidth           = 52
> OSDheight          = 18
> OSDMessageTime     = 1
> MaxVideoFileSize   = 2000
> SplitEditedFiles   = 0
> MinEventTimeout    = 30
> MinUserInactivity  = 120
> MultiSpeedMode     = 0
> ShowReplayMode     = 1
> CaCaps             = 1 101
> CurrentChannel     = 5
> CurrentVolume      = 255
> divxrecord         = 0
> divxx              = 720
> divxy              = 576
> divxbitrate        = 8
> divxquality        = 3
> MP3InitLoopMode    = 0
> MP3InitShuffleMode = 0
> MP3AudioMode       = 1
> MP3Id3PreScan      = 1
> MP3EditorMode      = 1
> MP3DisplayMode     = 3
> MP3BackgrMode      = 1
> MP3MenuMode        = 0
> MP3TargetLevel     = 25
> MP3LimiterLevel    = 70
>
>
> Any help appreciated!!!
>
>
>
> Mit freundlichen Grüssen
> Stefan Lang
>
>