[vdr] Re: SV: Re: SV: SV: SV: Re: arm crash

["Rienecker, Fa. Evenio, ITS P, M" <C.Rienecker@deutschepost.de>]

IIRC ftp://ftp.cadsoft.de/pub/people/kls/vdr/siemens_dvb-0.9.4.tgz
never had any reasons to upgrade.

CU,
Christian.

> -----Original Message-----
> From: Tomas Prybil [mailto:tomas.prybil@copper.se]
> Sent: Wednesday, July 31, 2002 12:03 PM
> To: 'vdr@linuxtv.org'
> Subject: [vdr] SV: Re: SV: SV: SV: Re: arm crash
> 
> 
> What version of the DVB driver are you using?
> 
> /t
> 
> -----Ursprungligt meddelande-----
> Från: Rienecker, Fa. Evenio, ITS P, M
> [mailto:C.Rienecker@deutschepost.de]
> Skickat: den 31 juli 2002 11:46
> Till: vdr@linuxtv.org
> Ämne: [vdr] Re: SV: SV: SV: Re: arm crash
> 
> 
> PPL are using vdr with CA modules.
> Yes, the card is sensitive to the additional heat coming
> from the modules.
> BUT your problems are uncharacteristic to the setup.
> I use an Irdeto module with a Siemens DVB-C.
> I never had any problems.
> Now I own a second card that is more sensitive:
> I do get picture artefacts if I close the housing or
> temperature exceeds 35 degrees Celsius.
> I mounted a tiny fan to ensure proper air circulation and
> everything is fine. Even when I silence (i.e. slow down)
> the fan by reducing voltage to 7V.
> 
> I NEVER had any arm crashes due to heat.
> 
> CU,
> Christian.
> 
> > -----Original Message-----
> > From: Tomas Prybil [mailto:tomas.prybil@copper.se]
> > Sent: Wednesday, July 31, 2002 11:33 AM
> > To: 'vdr@linuxtv.org'
> > Subject: [vdr] SV: SV: SV: Re: arm crash
> > 
> > 
> > I sent this message two weeks ago.
> > Because of the silence, should I assume either:
> > 1) Nobody really uses CA modules with VDR
> > 2) Use another version of DVB driver than the 2002-05-20 version
> > 3) go to sleep
> > 
> > 
> > /t
> > 
> > -----Ursprungligt meddelande-----
> > Från: Tomas Prybil [mailto:tomas.prybil@copper.se]
> > Skickat: den 17 juli 2002 16:19
> > Till: 'vdr@linuxtv.org'
> > Ämne: [vdr] SV: SV: Re: arm crash
> > 
> > 
> > Yeah, proper chilling solved one problem.
> > I could now run vdr for hours and record/replay without a glitch.
> > 
> > But unfortunately the arm crashes again when I try to watch 
> encrypted
> > channels, either with viaacess or conax :( the crash comes 
> > within minutes
> > after enabling the ca modules....
> > 
> > Any ideas most appreciated.
> > 
> > /t
> > 
> > -----Ursprungligt meddelande-----
> > Från: Tomas Prybil [mailto:tomas.prybil@copper.se]
> > Skickat: den 16 juli 2002 22:16
> > Till: 'vdr@linuxtv.org'
> > Ämne: [vdr] SV: Re: arm crash
> > 
> > 
> > Could be an idea.
> > 
> > /t
> > 
> > -----Ursprungligt meddelande-----
> > Från: Rene Bartsch [mailto:rene@bartschnet.de]
> > Skickat: den 16 juli 2002 22:12
> > Till: vdr@linuxtv.org
> > Ämne: [vdr] Re: arm crash
> > 
> > 
> > Am Die, 2002-07-16 um 21.11 schrieb Tomas Prybil:
> > > 
> > > Dear list readers.
> > > 
> > > I have vdr 1.0.4 together with a 1.5 card installed in a 
> > Compaq EN SFF box
> > > together with a slimmed 2.4.10 kernel. I use the siemens 
> 0520 driver
> > > The problem is that the arm always crashes in a few minutes.
> > > 
> > > I've changead almost everything: the PC, linux 
> > distribution, with/without
> > > encryption, with/without lirc, vdr version, DVB driver version....
> > > 
> > 
> > What about temperature? Did you try cooling the Tuner? 
> DVB-S get very
> > hot ...
> > 
> > Rene
> > 
> > 
> > 
> > 
> > 
> > 
> 
> 
>