[linux-dvb] Terratec Cinergy S PCI

[Julian Picht]

Hi List.

I recently bought a Terratec Cinergy S PCI which uses a Conexant CX2388x 
chip as it's PCI Interface and a Fujitsu MB86A16 as it's frontend.

I modified the cx88 files to recognize this card. Now I need a some 
pointers how to attach the MB86A16 frontend (which is included in mantis 
source, i think) to the cx88 and how to obtain the right i2c adresses etc.

Is there any documentation on how to do that?
I would be very happy to contribute to the great work you do and already 
did.

--------------------------------------
# lspci -vvnn
04:01.0 Multimedia video controller [0400]: Conexant CX23880/1/2/3 PCI 
Video and Audio Decoder [14f1:8800] (rev 05)
   Subsystem: TERRATEC Electronic GmbH Device [153b:117a]
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 22
   Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
   Capabilities: <access denied>
   Kernel driver in use: cx8800
   Kernel modules: cx8800

04:01.2 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video 
and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)
   Subsystem: TERRATEC Electronic GmbH Device [153b:117a]
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 5
   Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
   Capabilities: <access denied>
   Kernel modules: cx8802

04:01.4 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video 
and Audio Decoder [IR Port] [14f1:8804] (rev 05)
   Subsystem: TERRATEC Electronic GmbH Device [153b:117a]
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32 (1500ns min, 63750ns max), Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 5
   Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
   Capabilities: <access denied>

--------------------------------------
# i2cdetect -l
i2c-0    smbus         SMBus I801 adapter at 0400          SMBus adapter
i2c-1    i2c           cx88[0]                             I2C adapter
# i2cdetect 1
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-1.
I will probe address range 0x03-0x77.
Continue? [Y/n]
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- 08 -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: UU -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
--------------------------------------

Thanks in advance! Any help appreciated!

Julian Picht