[linux-dvb] Compro E800F Hybrid D/A HW2 PCIe card
Thomas Goerke
tom at goeng.com.au
Thu Jul 24 16:43:59 CEST 2008
I have now found that the E800 card is not
supported (http://www.linuxtv.org/wiki/index.php/DVB-T_PCIe_Cards). I
am willing to test any code and have so far patched the v4l-dvb and the
card semi-works...ie I can run the scan using local au-perth.conf file
but I am unanle to sync.
FYI - I am runnign mythbuntu 8.04.
On Thu, Jul 24, 2008 at 01:03:42AM +0800, Thomas Goerke wrote:
> I have purchased a Compro E800F Hybrid D/A HW2 PCIe card. The chips on the card include:
> Conexant PCIe A/V decoder: CX23885-132
> Conexant MPEG II A/V/Encoder CX23417-11Z
> Zarlink ZL10353 Demodulator
> Xceiver XC3008ACQ Video Tuner
> I have tried a number of solutions including building the latest copy of v4l-dvb and using the cx23885 module with card=4 option.
> The problem I am having is that the lgdt330x module is being loaded with the cx23885, however my demodulator is the zarlink ZL10353. I am not sure on how to proceed. Please see below for output of lspci -vvnn.
>
> 03:00.0 Multimedia video controller [0400]: Conexant Unknown device [14f1:8852] (rev 02)
> Subsystem: Compro Technology, Inc. Unknown device [185b:e800]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 17
> Region 0: Memory at fe800000 (64-bit, non-prefetchable) [size=2M]
> Capabilities: [40] Express Endpoint IRQ 0
> Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
> Device: Latency L0s <64ns, L1 <1us
> Device: AtnBtn- AtnInd- PwrInd-
> Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
> Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
> Link: Latency L0s <2us, L1 <4us
> Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
> Link: Speed 2.5Gb/s, Width x1
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [90] Vital Product Data
> Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
> Address: 0000000000000000 Data: 0000
>
> Any help appreciated.
>
> Thanks
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
More information about the linux-dvb
mailing list