[linux-dvb] Anysee E30 Combo Plus startup mode

Alexander Saers alex at saers.com
Fri Aug 21 15:21:39 CEST 2009


Hello

I have a Anysee E30 Combo Plus USB device. It's capable of both DVB-C and
DVB-T. I currently use the device with ubuntu 9.04 64bit with mythtv. I have
problem with selction of mode for the device

The following way i can get DVB-T
1. Power up computer with E30 Combo Plus connected.
2. run dmesg
<dmesg shows>
...
[   12.254209] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
[   12.254356] dvb-usb: will pass the complete MPEG2 transport stream to the
software demuxer.
[   12.255832] DVB: registering new adapter (Anysee DVB USB2.0)
[   12.259593] anysee: firmware version:0.1.2 hardware id:15
[   12.276531] generic-usb 0003:046D:C505.0002: input,hidraw1: USB HID v1.10
Mouse [Logitech USB Receiver] on usb-0000:00:04.0-3/input1
[   12.276610] usbcore: registered new interface driver usbhid
[   12.276690] usbhid: v2.6:USB HID core driver
[   12.392415] DVB: registering adapter 0 frontend 0 (Zarlink ZL10353
DVB-T)...
[   12.428278] input: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00: 04.1/usb1/1-2/input/input6
[   12.460271] dvb-usb: schedule remote query interval to 200 msecs.
[   12.460284] dvb-usb: Anysee DVB USB2.0 successfully initialized and
connected.
[   12.463685] usbcore: registered new interface driver dvb_usb_anysee
...
</dmesg shows>
3. rmod dvb_usb_anysee
4. modprobe dvb_usb_anysee delsys=0
5. run dmesg -> stil dvb-t :(


The following way i can get DVB-C. But its kind of anoying to remove the
device during every boot.
1. Power up computer with E30 Combo Plus disconnected.
2. Wait until everything has loaded and gdm is seen on the monitor
3. Connect the E30 Combo Plus.
4. Device is detected as a DVB-C device
5. dmesg
<dmesg shows>
[   64.464258] dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
[   64.464356] dvb-usb: will pass the complete MPEG2 transport stream to the
software demuxer.
[   64.464601] DVB: registering new adapter (Anysee DVB USB2.0)
[   64.469473] anysee: firmware version:0.1.2 hardware id:15
[   64.564746] DVB: registering adapter 0 frontend 0 (Philips TDA10023
DVB-C)...
[   64.597789] input: IR-receiver inside an USB DVB receiver as
/devices/pci0000:00/0000:00:04.1/usb1/1-2/input/input6
[   64.628139] dvb-usb: schedule remote query interval to 200 msecs.
[   64.628149] dvb-usb: Anysee DVB USB2.0 successfully initialized and
connected.
[   64.634715] usbcore: registered new interface driver dvb_usb_anysee

</dmesg shows>

Anyone experienced this problem? It would be nice to run DVB-C without
having to disconnect and connect hardware.

Br
Alexander
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.linuxtv.org/pipermail/linux-dvb/attachments/20090821/be709ef1/attachment.htm>


More information about the linux-dvb mailing list