Support for its digital side was added to Hg in September 2009.
- 1 Overview/Features
- 2 Making it Work
- 3 Making it Work Easily
- 4 Making it work using a GUI
- 5 Alternative method using (older) mercurial tree:
- 6 External Links
Features a hardware MPEG2 encoder and dual tuners (DVB-T/Analog TV Input)
Based on as far as I know: PCIe dual channel hybrid PC TV PCV520/20
- TDA18271 - Tuner (http://www.nxp.com/acrobat_download/literature/9397/75015474.pdf)
- In Latest HG
- NXP SAA7164E - NXP PCI Express dual-channel, PC TV capture/encode IC
- In Development by Steven Toth
- In Latest HG
02:00.0 Multimedia controller: Philips Semiconductors Unknown device 7164 (rev 81) Subsystem: Hauppauge computer works Inc. Unknown device 8901 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 255 Region 0: Memory at fd400000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at fd000000 (64-bit, non-prefetchable) [size=4M] Capabilities:  Message Signalled Interrupts: Mask- 64bit+ Queue=0/4 Enable- Address: 0000000000000000 Data: 0000 Capabilities:  Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x2, ASPM L0s L1, Latency L0 <4us, L1 <64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities:  Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [7c] Vendor Specific Information <?> Capabilities:  Vendor Specific Information <?> Capabilities:  Virtual Channel <?>
Making it Work
- Install the firmware:
wget http://www.steventoth.net/linux/hvr22xx/22xxdrv_27086.zip wget http://www.steventoth.net/linux/hvr22xx/HVR-12x0-14x0-17x0_1_25_25271_WHQL.zip wget http://www.steventoth.net/linux/hvr22xx/extract.sh sh extract.sh cp *fw /lib/firmware # for some linux distros, might need the following line instead of the above cp *fw /lib/firmware/`uname -r`
- Using current linuxtv git tree (http://www.linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers):
Install tools. For Ubuntu or debian:
apt-get install get patchutils lsdiff libproc-processtable-perl build-essential
At this point you should install the source or at least the headers for your kernel. The linuxtv drivers probably need to build against your kernel source. I am not 100% sure on this requirement, but it seems like an easy enough step to take.
Download the build tree and build it. It will download compatibility patches for your kernel if available:
git clone git://linuxtv.org/media_build.git cd media_build ./build.sh
Note: this method (as of 2012/03/02) will only give NTSC for analog TV, the driver does not have PAL support. You can at this point patch your code with the patch here: http://thread.gmane.org/gmane.linux.drivers.video-input-infrastructure/26212/focus=26524. A bit of fiddling is needed to apply the patch in the newer kernels, but I have it working with 3.2.1. Apply the patch to the linux subdirectory of the git archive (after calling ./build.sh), and then call ./build again (or just make). --- patch for 3.2.1-gentoo kernel: https://github.com/reinhrst/nl.claude.tools/tree/2594dd91cb81a3c905a53b9168f52a42e317cd1f/misc
Note: (as of 2012/11/27) Revision 2 of this card will fail to initialize correctly with a dmesg error similar to the below: Full details are available here
[ 3.682021] saa7164 driver loaded [ 3.682640] CORE saa7164: subsystem: 0070:8900, board: Hauppauge WinTV-HVR2200 [card=5,autodetected] [ 3.682646] saa7164/0: found at 0000:02:00.0, rev: 129, irq: 16, latency: 0, mmio: 0xfe400000 [ 3.693267] saa7164_downloadfirmware() firmware corrupt [ 3.693277] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw) [ 3.705989] saa7164_downloadfirmware() firmware read 4019072 bytes. [ 3.705995] saa7164_downloadfirmware() firmware loaded. [ 3.705996] Firmware file header part 1: [ 3.705999] .FirmwareSize = 0x0 [ 3.706000] .BSLSize = 0x0 [ 3.706001] .Reserved = 0x3d538 [ 3.706003] .Version = 0x3 [ 3.706005] saa7164_downloadfirmware() SecBootLoader.FileSize = 4019072 [ 3.706010] saa7164_downloadfirmware() FirmwareSize = 0x1fd6 [ 3.706012] saa7164_downloadfirmware() BSLSize = 0x0 [ 3.706014] saa7164_downloadfirmware() Reserved = 0x0 [ 3.706015] saa7164_downloadfirmware() Version = 0x1661c00 [ 8.247111] saa7164_downloadimage() image corrupt [ 8.247139] bootloader d/l has failed [ 8.247368] Failed to boot firmware, no features registered
To get the card working you'll have to
Now that we've built all the latest linuxtv drivers install them (from the media_build folder):
sudo make install
Finally reboot to load the driver (or use sudo make unload, then sudo modprobe driver name to unload and reload the drivers - see http://www.linuxtv.org/wiki/index.php/How_to_Obtain,_Build_and_Install_V4L-DVB_Device_Drivers for more info.)
Note: Some kernels will not have enough free memory available for the driver. The dmesg error will start with a message like this:
] modprobe: page allocation failure: order:10, mode:0x2000d0
followed by a stack trace and other debugging information. While the driver will load, no devices will be registered.
The simple workaround is to allocate more memory for the kernel:
sudo /bin/echo 16384 > /proc/sys/vm/min_free_kbytes sudo rmmod saa7164 sudo modprobe saa7164
- NB: One user found that the output of grep saa7164 /var/log/dmesg (on Ubuntu 11) was:
[ 4.604840] saa7164 driver loaded [ 4.604890] saa7164 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.606586] CORE saa7164: subsystem: 0070:8851, board: Hauppauge WinTV-HVR2250 [card=7,autodetected] [ 4.606591] saa7164/0: found at 0000:02:00.0, rev: 129, irq: 16, latency: 0, mmio: 0xe8000000 [ 4.606596] saa7164 0000:02:00.0: setting latency timer to 64 [ 4.764079] saa7164_downloadfirmware() no first image [ 4.764088] saa7164_downloadfirmware() Waiting for firmware upload (NXP7164-2010-03-10.1.fw) [ 4.947883] saa7164_downloadfirmware() Upload failed. (file not found?)
This necessitated the download of http://www.steventoth.net/linux/hvr22xx/firmwares/4019072/NXP7164-2010-03-10.1.fw and copy to /lib/firmware/<current kernel> (this firmware version doesn't get generated using the instructions further up the page).
- After running
sudo make unloadand
sudo modprobe saa7164the /dev/dvb/adapter0&1 devices were properly populated.
Making it Work Easily
This was tested under Ubuntu 12.04
- Install the firmware file : NXP7164-2010-03-10.1.fw from there http://www.steventoth.net/linux/hvr22xx/firmwares/4019072/ , in the /lib/firmware folder .
- Create a file named options in the /etc/modprobe.d folder , the first line should have : options saa7164 card=8
card=8 is for most 2250 cards. card=4 for an 8940 card. To find out what number to put in the card=x do the following
dmesg | grep saa7164
The third line should have something like [card=8,insmod option]
NOTE: You should use dmesg to find the card number before you create the modprobe.d file. If you don't, it will use the card number you put in modprobe.d instead of autodetecting the card number (ugh!)
You can see a list of the card numbers here: http://linuxtv.org/hg/v4l-dvb/file/tip/linux/Documentation/video4linux/CARDLIST.saa7164
In your dmesg option, you can find card version in the line that includes the word subsystem. Mine was 0070:8851 which is card=7 not 8.
WARNING: Another user here... These Making it Work Easily instructions did not work for me (Mythbuntu 12.04.3). These instructions only install the NXP7164 firmware. This initially appeared to get the card to work, however every 10-30 minutes or so I would get very bad pixellation issues that lasted for approx 1-2 minutes, before going good again. On inspection, the dmesg log contained a reference to another missing firmware dvb-fe-tda10048-1.0.fw. I then followed the instructions on this page in the Making it work section to install the firmware by manually extracting from the zip file. This fixed up the issue completely.
Hit the same problem in Ubuntu 14.04 with Making it Work Easily where dmesg showing missing dvb-fe-tda10048-1.0.fw message
Follow "Making it Work Easily" instructions, then:
# wget http://www.steventoth.net/linux/hvr22xx/22xxdrv_27086.zip # wget http://www.steventoth.net/linux/hvr22xx/HVR-12x0-14x0-17x0_1_25_25271_WHQL.zip # wget http://www.steventoth.net/linux/hvr22xx/extract.sh # sh extract.sh # sudo cp dvb-fe-tda10048-1.0.fw /lib/firmware # sudo reboot
Making it work using a GUI
I've put together a tv tuner config tool which sets up many cards:
Alternative method using (older) mercurial tree:
Install tools. For Mythdora:
yum install mercurial
For Ubuntu or Debian:
apt-get install mercurial libncurses5-dev
For stable tree
hg clone http://kernellabs.com/hg/saa7164-stable/ cd saa7164-stable
For development tree
hg clone http://kernellabs.com/hg/~stoth/saa7164-dev/ cd saa7164-dev
For Ubuntu or Debian, deconfigure the firedtv driver in the following process per Devin Heitmueller:
make menuconfig perl -p -i -e 's/FIREDTV=m/FIREDTV=n/' v4l/.config edit as needed but should have all enabled that is needed make make install reboot
For non-Ubuntu or Debian:
make menuconfig edit as needed but should have all enabled that is needed make make install reboot
Every time the linux kernel is upgraded to a new version, you'll need to reboot and then repeat the above steps.
MythDora: With a fresh Mythdora 10 install, chances are the above won't work until you install the kernel source code.
yum install kernel-devel
Repeat the make commands above after installing the kernel source.
Sample kernel output
saa7164 driver loaded ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16 saa7164 0000:02:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16 CORE saa7164: dev->lmmio = 0xf9800000 CORE saa7164: dev->lmmio2 = 0xf9c80000 CORE saa7164: dev->bmmio = 0xf9800000 CORE saa7164: dev->bmmio2 = 0xf9c80000 CORE saa7164: subsystem: 0070:8901, board: Hauppauge WinTV-HVR2200 [card=6,autodetected] saa7164/0: found at 0000:02:00.0, rev: 129, irq: 16, latency: 0, mmio: 0xfd400000 saa7164 0000:02:00.0: setting latency timer to 64 saa7164_downloadfirmware() no first image saa7164_downloadfirmware() Waiting for firmware upload (v4l-saa7164-1.0.2.fw) saa7164 0000:02:00.0: firmware: requesting v4l-saa7164-1.0.2.fw saa7164_downloadfirmware() firmware read 3978608 bytes. saa7164_downloadfirmware() firmware loaded. Firmware file header part 1: .FirmwareSize = 0x0 .BSLSize = 0x0 .Reserved = 0x3cb57 .Version = 0x3 saa7164_downloadfirmware() SecBootLoader.FileSize = 3978608 saa7164_downloadfirmware() FirmwareSize = 0x1fd6 saa7164_downloadfirmware() BSLSize = 0x0 saa7164_downloadfirmware() Reserved = 0x0 saa7164_downloadfirmware() Version = 0x51cc1 saa7164_downloadimage() Image downloaded, booting... saa7164_downloadimage() Image booted successfully. starting firmware download(2) saa7164_downloadimage() Image downloaded, booting... saa7164_downloadimage() Image booted successfully. firmware download complete. saa7164: i2c bus 0 registered saa7164: i2c bus 1 registered saa7164: i2c bus 2 registered tveeprom 3-0000: Hauppauge model 89619, rev B2F2, serial# 3019750 tveeprom 3-0000: MAC address is 00-0D-FE-2E-13-E6 tveeprom 3-0000: tuner model is NXP 18271C2_716x (idx 152, type 4) tveeprom 3-0000: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc) tveeprom 3-0000: audio processor is SAA7164 (idx 43) tveeprom 3-0000: decoder processor is CX23887A (idx 39) tveeprom 3-0000: has radio saa7164: Hauppauge eeprom: model=89619 tda18271 4-0060: creating new instance TDA18271HD/C2 detected @ 4-0060 DVB: registering new adapter (saa7164) DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)... tda18271 5-0060: creating new instance TDA18271HD/C2 detected @ 5-0060 DVB: registering new adapter (saa7164) DVB: registering adapter 3 frontend 0 (NXP TDA10048HN DVB-T)... tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)... i2c-adapter i2c-4: firmware: requesting dvb-fe-tda10048-1.0.fw tda10048_firmware_upload: firmware read 24878 bytes. tda10048_firmware_upload: firmware uploading tda10048_firmware_upload: firmware uploaded tda18271: performing RF tracking filter calibration tda18271: RF tracking filter calibration complete tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)... i2c-adapter i2c-5: firmware: requesting dvb-fe-tda10048-1.0.fw tda10048_firmware_upload: firmware read 24878 bytes. tda10048_firmware_upload: firmware uploading tda10048_firmware_upload: firmware uploaded tda18271: performing RF tracking filter calibration tda18271: RF tracking filter calibration complete
MythDora: A non-programmer, Linux and MythTV newbie wrote the added details about MythDora 10. I got the driver to work using Kernel 220.127.116.11-170.2.113.fc10.x86_64, by installing Mercurial and kernel-devel (plus a few other guesses, documented in the Discussion tab). Other research suggested I needed ncurses and ncurses-devel, and gcc, but I'm not sure of those are really required. Hopefully someone comes along and corrects any errors and incorporates additional information in this main article, which I found most useful.
Verifying it Works
- Another user here on Debian (KDE mostly). I am unable to verify/use card as I am clueless about setting up media center type software to put it to use.
Doesn't work with Supermicro PCIe Gen3 slot motherboards
I tried to use it with a Supermicro X11SAT-F (Bios 2.0c, Release Date: 10/20/2017) and X10DRi-T (Bios 2.1a, Release Date: 05/05/2017) motherboards which have PCIe GEN 3 slots only. For both the motherboards the PCIe link speed was changed from Auto to Gen1 in the BIOS. The card was not detected by the X11SAT-F motherboard, however it was detected by X10DRi-T. Hauppauge techsupport said "The board is not supported on those Xeon Supermicro motherboards. We had discussions with Supermicro a couple of years ago about this and the simple conclusion was that the card would need a physical modification to make it work"