Hauppauge WinTV-HVR-4000: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
No edit summary
(add formatting and prompts for end users to start contributing)
Line 1: Line 1:
[[Image:Hauppague WinTV-HVR-4000.jpg|right|250px|The HVR-4000 and Remote]]

A hybrid [[DVB-S2]] [[DVB-S2 PCI Cards|PCI card]] from [[Hauppauge]].

It is currently not supported under Linux. However, experimental support for some of the device's features is available (see below for details).

==Overview/Features==
''Discuss the features and facets of the device here ... this means you''

===Components Used===
''list the hardware ICs and modules used by the device here ... this means you''

===Identification===
''provide the relevant output of lspci -vvn here ... this means you''


==Making it Work==

===Firmware===
''is there any firmware specific information for this card? if so, list it here ... this means you''

===Drivers===
There are currently no in kernel drivers for this card.

''If someone wants to provide a brief synopsis of the driver tail of woe, outlining why there isn't a greater level of support, then do so here ... this means you''

However, experimental support does exist.

''provide the details of where the drivers and patches and necessary tools are available ... this means you ... you can use the following older content from the article as a basis for your write up:''

For DVB-S there is an experimental drivers repository from Steven Toth (see http://www.linuxtv.org/hg/~stoth/hvr4000-dvbs). Analog video and remote control works also with this driver (*).
For DVB-S there is an experimental drivers repository from Steven Toth (see http://www.linuxtv.org/hg/~stoth/hvr4000-dvbs). Analog video and remote control works also with this driver (*).


Line 9: Line 39:
This patchset also adds two hacks which will allow DVB-S2 reception (command line) for experimental purposes, also it allows the selection of which DVB frontend to load, DVB-T or DVB-S/S2.
This patchset also adds two hacks which will allow DVB-S2 reception (command line) for experimental purposes, also it allows the selection of which DVB frontend to load, DVB-T or DVB-S/S2.


== DVB-T ==
'''DVB-T'''


For DVB-T a special option for the module cx88xx is needed:
For DVB-T a special option for the module cx88xx is needed:
Line 26: Line 56:


(Yes, on my system I need to use "card='''53'''" - not "card=56" - to get DVB-T to work)
(Yes, on my system I need to use "card='''53'''" - not "card=56" - to get DVB-T to work)

===Sample kernel output===
''provide the relevant portion of dmesg here''

===Remote Control Support===
''discuss support for the remote control here''

==External Links==
* [http://www.hauppauge.co.uk/pages/products/data_hvr4000.html Hauppauge UK's HVR-4000 product page]

Revision as of 15:00, 16 January 2008

The HVR-4000 and Remote

A hybrid DVB-S2 PCI card from Hauppauge.

It is currently not supported under Linux. However, experimental support for some of the device's features is available (see below for details).

Overview/Features

Discuss the features and facets of the device here ... this means you

Components Used

list the hardware ICs and modules used by the device here ... this means you

Identification

provide the relevant output of lspci -vvn here ... this means you


Making it Work

Firmware

is there any firmware specific information for this card? if so, list it here ... this means you

Drivers

There are currently no in kernel drivers for this card.

If someone wants to provide a brief synopsis of the driver tail of woe, outlining why there isn't a greater level of support, then do so here ... this means you

However, experimental support does exist.

provide the details of where the drivers and patches and necessary tools are available ... this means you ... you can use the following older content from the article as a basis for your write up:

For DVB-S there is an experimental drivers repository from Steven Toth (see http://www.linuxtv.org/hg/~stoth/hvr4000-dvbs). Analog video and remote control works also with this driver (*).

Currently, no support for simultaneous operation of both DVB-T and DVB-S is implemented. Default operation mode prefers DVB-S.

Guess Note : Using HVR3000 as example the DVB-T and DVB-S use the same demux on the card, so only one will ever be available. The above I expect to be the same for the HVR4000, ie not a linuxtv issue. It is suggested to create symbolic links to access the frontends for some apps (see HVR3000 in this wiki), but you need to ensure your application does not attempt to access both DVB-T and DVB-S at the same time.

(*) Work in progress patches to enable features of this card have been merged into the hvr4000-dvbs repository, yet an updated patchset is available for v4l-dvb hg here: http://dev.kewl.org/hvr4000/

This patchset also adds two hacks which will allow DVB-S2 reception (command line) for experimental purposes, also it allows the selection of which DVB frontend to load, DVB-T or DVB-S/S2.

DVB-T

For DVB-T a special option for the module cx88xx is needed: card=56

The card is automatically detected as card 57. Therefore, using OpenSuSE (and probably also other distros) add the line

options cx88xx card=56

in /etc/modprobe.conf.local (or /etc/conf.modules or similar).


For Ubuntu make a file /etc/modprobe.d/cx88xx.modprobe with the following contents:

options cx88xx card=53

(Yes, on my system I need to use "card=53" - not "card=56" - to get DVB-T to work)

Sample kernel output

provide the relevant portion of dmesg here

Remote Control Support

discuss support for the remote control here

External Links