It is natively supported under Linux since kernel 2.6.19.
In actuality, the device's receivers are USB based, but there aren't any USB plugs or sockets involved -- the single PCI card itself sports on board dual USB based receivers that interface with a host USB 2.0 controller (USB to PCI). This unique design is also known as "Bristol".
- 2x Microtune MT2060 tuner
- 2x DiB3000P DiBcom DVB-T demodulator & USB controller
- 1x VIA VT8xxx host USB 2.0 controller (USB-to-PCI)
- A single Low Noise Amplifier (LNA) is present for both channels, but needs to be manually activated (see below).
Some further technical details may be found in DiBcom DiB0700 USB2.0 DVB-T based devices.
You will find the model name and number on the box, under the bar code. Cards known to work have the following:
- WinTV-NOVA-T-500 model 289 SL-289-V2.0-UK (in the UK there is also a model 287 - according to Hauppauge UK support this is identical to the model 289 - it is just a PC World/Dixons specific box)
- WinTV-NOVA-T-500 model 289 SL-289-V2.1-UK ... Note: It would appear that having V2.1 on the box could be either the Nova-T or the unsupported Nova-TD (see below). Most confusing!
- List incomplete, please add
Making it work
You will need the dvb-usb-dib0700-03-pre1.fw firmware file in
or the relevant place for your distribution.
It requires the dib0700 driver. Just use Mercurial by following the How to install DVB device drivers instructions.
Note: the current drivers are not too stable at the moment (2007-09-23). Occasional USB disconnects are being experienced (I lose approx 5 out of 40 recordings in MythTV from the problem). Search the linux-dvb mailing list for more information and current problems being experienced.
You may want/need to turn on the on-board amplifier:
sudo gedit /etc/modprobe.d/options
options dvb-usb-dib0700 force_lna_activation=1
Sample kernel output
[ 30.965645] dib0700: loaded with support for 5 different device-types [ 30.965925] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 31.008899] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-03-pre1.fw' [ 31.206081] dib0700: firmware started successfully. [ 31.711176] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state. [ 31.711222] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 31.711325] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T) [ 31.831535] DVB: registering frontend 0 (DiBcom 3000MC/P)... [ 31.854890] MT2060: successfully identified (IF1 = 1220) [ 32.388673] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 32.388853] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T) [ 32.394293] DVB: registering frontend 1 (DiBcom 3000MC/P)... [ 32.398790] MT2060: successfully identified (IF1 = 1220) [ 32.959607] input: IR-receiver inside an USB DVB receiver as /class/input/input4 [ 32.959633] dvb-usb: schedule remote query interval to 150 msecs. [ 32.959637] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T successfully initialized and connected. [ 32.959657] usbcore: registered new interface driver dvb_usb_dib0700
Grey top, black bottom, 45 buttons, snowboard shape.
Support for the tuners on the card was implemented earlier than support for the remote control - as a result you may find the tuners work but the IR-receiver for the remote control is not detected. You can check the installed version of the driver has detected the remote control by looking in the 'dmesg' output for a line similar to:
input: IR-receiver inside an USB DVB receiver as /class/input/inputX
(where X will vary depending in your system configuration).
Additionally, the IR receiver will be listed if you execute the command:
I: Bus=0003 Vendor=2040 Product=9950 Version=0100 N: Name="IR-receiver inside an USB DVB receiver" P: Phys=usb-0000:00:0d.2-1/ir0 S: Sysfs=/devices/pci0000:00/0000:00:0d.2/usb8/8-1/input/input6 U: Uniq= H: Handlers=kbd event6 B: EV=3 B: KEY=14afc336 284284d 0 0 0 4 80058000 2190 40000801 9e96c0 0 900200 ffd
If the IR receiver is not detected but you can see the detection of the tuners (see earlier in this page) then you will need to patch your kernel with the latest mercurial v4l-dvb sources (see ). This was required even with Gentoo kernel 2.6.23-r3.
The remote control gives output into
where X is variable and depends on your system.
LIRC will use it without needing a special kernel module. use the following driver:
Here is a proper lircd.conf file:
# # brand: Hauppauge NOVA-T-500 # model no. of remote control: Hauppage Nova-T-500 Snowboard Shape Silver over Black # begin remote name NOVA-T500 bits 16 eps 30 aeps 100 one 0 0 zero 0 0 pre_data_bits 16 pre_data 0x1 gap 199999 toggle_bit 0 begin codes Go 0x0162 Power 0x0074 TV 0x0179 Videos 0x0189 Music 0x0188 Pictures 0x00E2 Guide 0x016D Radio 0x0181 ArrowUp 0x0067 ArrowLeft 0x0069 OK 0x0160 ArrowRight 0x006A ArrowDown 0x006C BackExit 0x009E Menu 0x008B VolumeUp 0x0073 VolumeDown 0x0072 PrevCh 0x016B Mute 0x0071 ChannelUp 0x0192 ChannelDown 0x0193 Record 0x00A7 Rewind 0x00A8 SkipBack 0x0195 Play 0x00CF Pause 0x0077 Stop 0x0080 Fwdwind 0x00D0 SkipFwd 0x0197 1 0x0002 2 0x0003 3 0x0004 4 0x0005 5 0x0006 6 0x0007 7 0x0008 8 0x0009 9 0x000A * 0x0037 0 0x000B # 0x0029 Red 0x018E Green 0x018F Yellow 0x0190 Blue 0x0191 end codes end remote