Difference between revisions of "Leadtek WinFast DTV Dongle Gold"

From LinuxTVWiki
Jump to: navigation, search
Line 22: Line 22:
 
  input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7
 
  input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7
  
To install the driver you will need your kernel headers and mercurial installed, kernel headers and mercurial can be installed under Ubuntu by running  
+
To install the driver you will need your kernel headers and mercurial installed, kernel headers and mercurial can be installed under Ubuntu by running :
  
 
<code>sudo apt-get install linux-headers-generic mercurial</code>
 
<code>sudo apt-get install linux-headers-generic mercurial</code>
  
To install the driver enter the following commands into a terminal
+
To install the driver enter the following commands into a terminal:
  
 
  1) hg clone http://linuxtv.org/hg/~anttip/af9015-mxl500x
 
  1) hg clone http://linuxtv.org/hg/~anttip/af9015-mxl500x
Line 93: Line 93:
 
  input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7
 
  input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7
  
Also if you run <code>ls /dev/dvb/</code> in a terminal you should see a new dvb adapter
+
Also if you run <code>ls /dev/dvb/</code> in a terminal you should see a new dvb adapter.
  
 
==Troubleshooting==
 
==Troubleshooting==
Line 109: Line 109:
 
  usbcore: registered new interface driver dvb_usb_af9015
 
  usbcore: registered new interface driver dvb_usb_af9015
  
* Solution: You have not installed the firmware correctly, please rerun steps 5 and 6 of the installation procedure, if the firmware is unavailable you may have to retrieve a copy from another location
+
* Solution: You have not installed the firmware correctly, please rerun steps 5 and 6 of the installation procedure, if the firmware is unavailable you may have to retrieve a copy from another location.
  
 
==External Links==
 
==External Links==

Revision as of 04:52, 25 September 2008

A DVB-T USB device from Leadtek.

Overview/Features

  • Supplied with a remote control and antenna.

Components Used

  • Microtune MT2060 tuner
  • Dibcom DiB7700B/C DVB-T demodulator

Identification

There is only one variant of this device. The USB ID is:

  • 0413:6029

Driver Installation

By default on Ubuntu 8.04 or any 2.6.24 kernel the driver for the TV tuner is not supplied and must be installed separately. If you plug in the TV tuner without the driver installed only the IR sensor for the remote will be detected. dmesg output:

input: Leadtek WinFast DTV Dongle Gold as /devices/pci0000:00/0000:00:13.5/usb6/6-7/6-7:1.1/input/input7
input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7

To install the driver you will need your kernel headers and mercurial installed, kernel headers and mercurial can be installed under Ubuntu by running :

sudo apt-get install linux-headers-generic mercurial

To install the driver enter the following commands into a terminal:

1) hg clone http://linuxtv.org/hg/~anttip/af9015-mxl500x
2) cd af9015-mxl500x/
3) make
4) sudo make install
5) wget http://www.otit.fi/~crope/v4l-dvb/af9015/af9015_firmware_cutter/firmware_files/4.95.0/dvb-usb-af9015.fw
6) sudo mv dvb-usb-af9015.fw /lib/firmware/

Your TV tuner's driver is installed now, to load the driver either run sudo modprobe dvb_usb_af9015 or reconnect you TV tuner. You can check that the driver is loaded correctly by running dmesg in a terminal, your out put should be similar to this:

input: Leadtek WinFast DTV Dongle Gold as /devices/pci0000:00/0000:00:13.5/usb6/6-7/6-7:1.1/input/input11
input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7
af9015_usb_probe: interface:0
af9015_identify_state: reply:01
dvb-usb: found a 'Leadtek WinFast DTV Dongle Gold' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
af9015_download_firmware:
usbcore: registered new interface driver dvb_usb_af9015
usb 6-7: USB disconnect, address 36
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 6-7: new high speed USB device using ehci_hcd and address 37
usb 6-7: configuration #1 chosen from 1 choice
af9015_usb_probe: interface:0
af9015_identify_state: reply:02
dvb-usb: found a 'Leadtek WinFast DTV Dongle Gold' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek WinFast DTV Dongle Gold)
af9015_eeprom_dump:
00: 31 c2 bb 0b 00 00 00 00 13 04 29 60 00 02 01 02 
10: 00 80 00 fa fa 10 40 ef 01 30 31 30 31 30 32 30 
20: 35 30 35 30 30 30 30 31 ff ff ff ff ff ff ff ff 
30: 00 00 3a 01 00 08 02 00 cc 10 00 00 9c ff ff ff 
40: ff ff ff ff ff 08 02 00 1d 8d c4 04 82 ff ff ff 
50: ff ff ff ff ff 26 00 00 04 03 09 04 10 03 4c 00 
60: 65 00 61 00 64 00 74 00 65 00 6b 00 30 03 57 00 
70: 69 00 6e 00 46 00 61 00 73 00 74 00 20 00 44 00 
80: 54 00 56 00 20 00 44 00 6f 00 6e 00 67 00 6c 00 
90: 65 00 20 00 47 00 6f 00 6c 00 64 00 20 03 30 00 
a0: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00 
b0: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff 
c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
af9015_read_config: TS mode:0
af9015_read_config: xtal:2 set adc_clock:28000
af9015_read_config: IF1:4300
af9015_read_config: MT2060 IF1:0
af9015_read_config: tuner id1:156
af9015_read_config: spectral inversion:0
af9013: firmware version:4.95.0
DVB: registering frontend 0 (Afatech AF9013 DVB-T)...
af9015_tuner_attach: 
tda18271 7-00c0: creating new instance
TDA18271HD/C1 detected @ 7-00c0
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek WinFast DTV Dongle Gold)
dvb-usb: no frontend was attached by 'Leadtek WinFast DTV Dongle Gold'
dvb-usb: Leadtek WinFast DTV Dongle Gold successfully initialized and connected.
af9015_init:
af9015_init_endpoint: USB speed:3
af9015_download_ir_table:
input: Leadtek WinFast DTV Dongle Gold as /devices/pci0000:00/0000:00:13.5/usb6/6-7/6-7:1.1/input/input12
input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7

Also if you run ls /dev/dvb/ in a terminal you should see a new dvb adapter.

Troubleshooting

  • Problem: You have followed the step's above but when you run ls /dev/dvb/ there is no new adapter and your dmesg output is similar to this:
usb 6-7: new high speed USB device using ehci_hcd and address 31
usb 6-7: configuration #1 chosen from 1 choice
input: Leadtek WinFast DTV Dongle Gold as /devices/pci0000:00/0000:00:13.5/usb6/6-7/6-7:1.1/input/input8
input,hidraw0: USB HID v1.01 Keyboard [Leadtek WinFast DTV Dongle Gold] on usb-0000:00:13.5-7
af9015_usb_probe: interface:0
af9015_identify_state: reply:01
dvb-usb: found a 'Leadtek WinFast DTV Dongle Gold' in cold state, will try to load a firmware
dvb-usb: did not find the firmware file. (dvb-usb-af9015.fw) Please see linux/Documentation/dvb/ for more details on firmware-problems. (-2)
dvb_usb_af9015: probe of 6-7:1.0 failed with error -2
usbcore: registered new interface driver dvb_usb_af9015
  • Solution: You have not installed the firmware correctly, please rerun steps 5 and 6 of the installation procedure, if the firmware is unavailable you may have to retrieve a copy from another location.

External Links