TechniSat SkyStar HD: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
Line 41: Line 41:


===Modules===
===Modules===
With current drivers the required modules should all load correctly on boot.
You need to


modprobe stb0899 stb6100 saa7146 lnbp21
modprobe stb0899 stb6100 saa7146 lnbp21
modprobe budget-ci
modprobe budget-ci
Line 48: Line 50:
DVB: Unable to find symbol stb6100_attach()
DVB: Unable to find symbol stb6100_attach()
As with all DVB drivers, if you don't see any cards and frontends in multiproto's menuconfig, enable I2C in your kernel config and in multiproto do make distclean afterwards.
As with all DVB drivers, if you don't see any cards and frontends in multiproto's menuconfig, enable I2C in your kernel config and in multiproto do make distclean afterwards.

'''Note:''' ''You can find these modules over at [http://jusst.de/hg/multiproto/ http://jusst.de/hg/multiproto/]''




==External Links==
==External Links==

Revision as of 23:41, 28 January 2009

A DVB-S2 PCI card by TechniSat. For the SkyStar HD2 please see the Azurewave AD-SP400 CI (Twinhan VP-1041).

Experimental support exists.

Overview

Apparently the card is actually a rebranded TechnoTrend TT-budget S2-3200. See that page for more details.

Components Used

It also supports an add-on CI slot.

Identification

02:06.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
        Subsystem: Technotrend Systemtechnik GmbH Unknown device 1019
        Flags: bus master, medium devsel, latency 32, IRQ 20
        Memory at feaffc00 (32-bit, non-prefetchable) [size=512]
# lspci -v -n -s 02:06.0
02:06.0 0480: 1131:7146 (rev 01)
        Subsystem: 13c2:1019
        Flags: bus master, medium devsel, latency 32, IRQ 20
        Memory at feaffc00 (32-bit, non-prefetchable) [size=512]

output from lspci -vvv

01:00.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
        Subsystem: Technotrend Systemtechnik GmbH Unknown device 1019
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (3750ns min, 9500ns max)
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at e9cffc00 (32-bit, non-prefetchable)[size=512]

Drivers

See TechnoTrend TT-budget S2-3200.

Modules

With current drivers the required modules should all load correctly on boot.


modprobe stb0899 stb6100 saa7146 lnbp21
modprobe budget-ci

If you don't load the other modules first, you'll get

DVB: Unable to find symbol stb6100_attach()

As with all DVB drivers, if you don't see any cards and frontends in multiproto's menuconfig, enable I2C in your kernel config and in multiproto do make distclean afterwards.

External Links