|
I`ve tried to load siemens 0.8.2 drivers patched
with rolf siebrecht patch level 9f
On make there wasn`t any mistakes (exept min and
max redefines, but this is because gcc)
also make install, makedev.napi ....editing
devfs,modules.conf.... goes fine
modprobe dvb:
i2c-core.o: i2c core module version 2.6.5
(20020915)
kernel: PCI: Found IRQ 12 for device 00:0a.0 kernel: saa7146_core: saa7146 #0 @ pci 00:0a.0; rev=1; mem=0xe6002000; irq=12; subsys=0x13c2,0x0000. kernel: saa7146_core: saa7146 #0: using 2 capture buffers of 1728 KBytes each (3456 KBytes total) kernel: saa7146_core: saa7146 #0: latency=32 clks; threshold=32 dwrds; burst=128 dwrds. kernel: saa7146_core: 1 SAA7146 chipset(s)
found.
kernel: saa7146_core: extension 0 registered: "v4l extension" kernel: Linux video capture interface: v1.00 kernel: dvb.o Technotrend/Siemens DVB driver version 0.8.2 patch 9f kernel: dvb0: ambiguous subsystem id (0x13c2,0x0000) on saa7146 #0. kernel: dvb0: probing for I2C client VES1893 @ 0x08... found. kernel: dvb0: DVB-S Rev. 1.3 auto-detected on saa7146 #0. kernel: sp5659.o i2c driver kernel: sp5659: MITEL SP5659 #0 detected at i2c address 0x61. kernel: sp5659: MITEL SP5659 #0 @ 0x61 attached to adapter saa7146 #0. kernel: ves1893.o i2c driver kernel: ves1893: VLSI VES1893 #0 detected at i2c address 0x08. kernel: ves1893: VLSI VES1893 #0 @ 0x08 attached to adapter saa7146 #0. kernel: ee24lc16.o i2c driver kernel: ee24lc16: Serial EEPROM #0 detected at i2c address 0x50. kernel: ee24lc16: Serial EEPROM #0 @ 0x50 attached to adapter saa7146 #0. kernel: dvb0: V4L video device registered on (81, 0). kernel: dvb0: V4L vbi device registered on (81, 224). kernel: dvb0: ARM firmware successfully loaded. kernel: dvb0: firmware = f0240009 kernel: dvb0: MAC = XX XX XX XX XX XX kernel: saa7146_core: extension 1 registered: "dvb extension" kernel: dvb: 1 dvb(s) found! looks fine to me, but when I try to run dvbd (after
ifconfig dvb0 192.168.4.1 up)
nothing happens (in messages I see:
dvbd: reading config
dvbd: IP(net) for filter_0 is XXX.XX.XXX.XXX/255.255.255.255 dvbd: activating and I can`t see dvbd in ps aux)
in syslog I saw
dvbd: ioctl VIDIOCGCAP (dvbd.c, 1335): Unknown
error 515 - aborting
dvbd: ioctl VIDIOCSSHUTDOWNFILTER[0] (dvbd.c, 1033): Unknown error 515 so I go to line 1335 and cut all in /* check if DVB
card/driver is present at opened V4L device */
after recompiling , and trying to run now I
see Technotrend/Siemens DVB (Video) not present at /dev/ost/video0 -
aborting
anybody know, what`s going on ?
(on slack 8.0 and patch level 6 + 2.4.16 and old
i2c , I don`t remember which version It works fine)
kernel 2.4.18, i2c
2.6.5,gcc 2.95.3, slack 8.1 |