[linux-dvb] Re: Hauppauge Nexus-s 2.2 Debian Testing

[Matthew Reath <lnxmatt@earthlink.net>]

I needed to load the stv0299.0 frontend module and now dvbtune works.
I'm having a problem with the v4l interface now but I'll see how that
pans out and post if I can't figure it out.

Thanks,
Matt

On Mon, 2004-09-27 at 08:36, Matthew Reath wrote:
> I'm currently running Debian Testing (2.6.7 kernel) with the dvb-utils, dvbtune, and dvbstream packages installed. 
> 
> lspci -vvv outputs:
> 
> 0001:01:12.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
>         Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 16 (3750ns min, 9500ns max)
>         Interrupt: pin A routed to IRQ 52
>         Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=512]
> 
> It says 2.1 here but on the card itself it says Rev 2.2.  My problem is this during boot the hotplug service loads everything but there are a couple of error messages (marked with errors at the end of the line):
> 
> Linux video capture interface: v1.00
> saa7146: register extension 'dvb'.
> PCI: Enabling device 0001:01:12.0 (0004 -> 0006)
> saa7146: found saa7146 @ mem da2da000 (revision 1, irq 52) (0x13c2,0x0003).
> DVB: registering new adapter (Technotrend/Hauppauge PCI rev2.1).
> Technotrend/Hauppauge PCI rev2.1 adapter 0 has MAC addr = 00:d0:5c:22:ec:32
> gpioirq unknown type=0 len=0 <----
> DVB: AV7111(0) - firm f0240009, rtsl b0250018, vid 71010068, app 8000261c
> DVB: AV7111(0) - firmware supports CI link layer interface
> av7110(0): Crystal audio DAC detected
> videodev: "av7110" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/ <---
> saa7146_vv: saa7146 (0): registered device video0 [v4l2]
> av7110: found av7110-0.
> 
> And finally when I use dvbtune I get this: "frontend: 13FRONTEND DEVICE: No such device". After this I tried xawtv just to see if get anything off of /dev/video0 .  The window comes up with a green background and no video. I don't have a cable hooked up from my dish to it so this is expect, but at this point my system freezes and I have to do a hard reset. It seems like any access to /dev/video0 freezes the system.  IS this because I don't have a connection with my LNB yet? How about the dvbtune frontend error message?
> 
> Someone please let me know if you've run into a similar issue or have any ideas.
> 
> Thanks,
> Matt
> 
> 
>