[linux-dvb] Pinnacle PCTV SAT bttv

[Nando Romano]

Hi
 I change my account from romano_ferdinando at yahoo.it
in darkside_moon83 at yahoo.it

I have suse 9.2 with this kernel 2.6.8-24-smp and I
have these packages
v4l-tools 3.94-2
pwlib-plugins-v4l 1.8.0-3
v4l-conf 3.94-2
pwlib 1.8.0-3
dvb 1.1.0_CVS20040812-7
devs 9.2-1

The PCI ID of PCTV SAT is  11bd:001c 
I obtained this value from dmesg 

bttv0: detected: Pinnacle PCTV Sat [card=94], PCI
subsystem ID is 11bd:001c

**********

>From the datasheet of pinnacle pc sat there are these
information

video digitalizer chip / control chip  PCI Conexant CN
878

numeric tuner TV /radio /dati Conexant HM 1211

Input sat antenna F connector SAT IF

passing band ( bandwidth) antenna output    F
connector SAT IF

video input
s video 
rca  


*********

If I type with root privileges 
# rcdvd start              
(it's like service dvb start)
(load all dvb dviver)


dmesg show me 

v4l2_common: unsupported module, tainting kernel.
v4l1_compat: unsupported module, tainting kernel.
video_buf: unsupported module, tainting kernel.
saa7146: register extension 'dvb'.
evdev_connect: evdev f7dcb880 handle f7dcb89c name
event3
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for
capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 19 (level,
low) -> IRQ 177
bttv0: Bt878 (rev 17) at 0000:02:07.0, irq: 177,
latency: 64, mmio: 0xf7c00000
bttv0: detected: Pinnacle PCTV Sat [card=94], PCI
subsystem ID is 11bd:001c
bttv0: using: Pinnacle PCTV Sat [card=94,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=009f00fc
[init]
i2c-algo-bit.o: (0) scl=1, sda=1
i2c-algo-bit.o: (1) scl=1, sda=0
i2c-algo-bit.o: (2) scl=1, sda=1
i2c-algo-bit.o: (3) scl=0, sda=1
i2c-algo-bit.o: (4) scl=1, sda=1
i2c-algo-bit.o: bt878 #0 [sw] passed test.
drivers/media/dvb/frontends/dib3000mb.c: did not found
a DiBCom 3000-MB.
bttv0: using tuner=-1
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI interrupt 0000:02:07.1[A] -> GSI 19 (level,
low) -> IRQ 177
bt878(0): Bt878 (rev 17) at 02:07.1, irq: 177,
latency: 64, memory: 0xf7d00000
bt878 find by dvb adap: checking "bt878 #0 [sw]"
bt878 find by dvb adap: NOT found "bt878 #0 [sw]"
mt312_read: ret == -121
i2c_adapter i2c-0: sendbytes: error - bailout.

Please note that I have also on my PC another tv card
(terrestrian) Typhoon 
tv tuner with chipset philips saa7134

then I type 
 # modprobe dvb-bt8xx
 # modprobe cx24110

and the output of dmesg isn't changed


Do you think I need some kind of firmware ?
Perhaps scmain.c?
Do you have any suggestions ?

Thank for your interest


		
___________________________________ 
Yahoo! Messenger: chiamate gratuite in tutto il mondo 
http://it.beta.messenger.yahoo.com