[linux-dvb] My Twinhan DVB-T CI won't tune

Henrik Sjöberg henke at epact.se
Tue Jun 14 14:59:11 CEST 2005


Hi,

This is probably the same card as I have. I posted a patch for this
earlier. The bandwidth byte needed to be send on another position when
tuning frequency. Also, the signal strengh byte was read from another
position as well.

Search my earlier posts and try it out.

Regards,
Henrik

-------------------
> Einar Bjarni Halldórsson wrote:
> >>Einar Bjarni Halldórsson wrote:
> >>>>>>Einar Bjarni Halldórsson wrote:
> >>>>>>>Hi,
> >>>>>>>
> >>>>>>>I finally got my hands on a DVB card, and have started what
is
> >>>>>>>becoming
> >>>>>>>a very interesting proccess of getting it to work. Had to
jump
> >>>>>>>through
> >>>>>>>a
> >>>>>>>couple of hoops to get the dst module to recognize it as a
DVB-T and
> >>>>>>>not
> >>>>>>>a DVB-S (the default KnoppMyth R5A16 install wouldn't budge
on this
> >>>>>>>issue). Since then I've tried kernels 2.6.10 , 2.6.11.11 and
> >>>>>>>2.6.12-rc5
> >>>>>>>with the CVS version of dvb-kernel, but with similar results.
The
> >>>>>>>card
> >>>>>>>get's recognized as a DVB-T and the CI module is recognized,
but when
> >>>>>>>I
> >>>>>>>try to get dvbscan to do it's thing, I get "tuning failed"
and a
> >>>>>>>bunch
> >>>>>>>of error messages in dmesg.
> >>>>>>>
> >>>>>>>I've seen people have similar problems in the mailing list
archives,
> >>>>>>>but
> >>>>>>>I was wondering if there is any progress in finding a
solution.
> >>>>>>Which card model do you have ?
> >>>>>>
> >>>>>I have a TwinhanDTV Ter-CI
> >>>>You have the Manufacturer and the Card type, but no Card model..
> >>>>The card model starts with VP-XXXXXX
> >>>>
> >>>The card is a VP-3040
> >>>
> >>The VP-3040 is a bit different kind of card, as per my knowledge
it has
> >>a detachable add-on CA board, and can have TS188 as well as TS204
too.
> >>
> > 
> > It has a separate add-on CA board that uses it's own PCI slot and
is
> > connected to the DVB card via flat cable.
> >
> 
> I don't have this card with me except for it's description..
> 
> >>I need to add some more code to correctly identify this board..
> >>Temporarily you can try force it to use TS188
(DST_TYPE_HAS_NEWTUNE) or
> >>TS204 (without the NEWTUNE option) and see how it goes..
> >>
> > 
> > How can I do that? It seems the dst_type_flags parameter has been
removed
> > from the dst module. If you mean I should hard-code it into the
source,
> > then I'm going to need some info on where it's set.
> >
> 
> the type_flags were removed since at that point of time it was
thought 
> that type_flags could be automatically determined by the card type.
> 
> Well almost true, except for cards with removable CI slots, where
the 
> tuner could be different. This can be autodetected but, trying to
make 
> out a bit of mandarin.
> 
> >>Possibility is that probably the Tuner type will be the other case
what
> >>is exactly for you at the momemt and hence communication errors..
> >>
> >>Let me know how this goes .. You will need some more patches, i
will
> >>post it a while later in the night .. In the meantime you can
check out
> >>which tuner type works appropriate for you .. (You should not see
any
> >>i2c communication errors, except in the case of a very weak
signal, if
> >>you gone through the right steps)
> >>
> > 
> > I will test anything you throw at me, and let you know how it
goes. I
> 
> 
> in the dst_tlist for your setup, for DTT-CI see the difference
without 
> the |DST_TYPE_HAS_NEWTUNE and with it also.
> 
> Try the same with the patches i posted earlier too..
> 
> Manu
> 
> 
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> 




More information about the linux-dvb mailing list