[linux-dvb] Twinhan experimental branch

Manu Abraham manu at kromtek.com
Sat Mar 12 21:29:35 CET 2005


Thomas Knauer wrote:
> Hi,
> 
> manu at kromtek.com (Manu Abraham) writes:
> 
> 
>>>Kernel is 2.6.11-rc2, because later kernels crash the system when
>>>the bttv module is loaded.
>>>
>>>bttv: Bt8xx card found (1).
>>>ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 19 (level, low) -> IRQ 19
>>>bttv1: Bt878 (rev 17) at 0000:01:0a.0, irq: 19, latency: 64, mmio: 0xf8001000
>>>bttv1: subsystem: 00a0:bcf8 (UNKNOWN)
>>>please mail id, board name and the correct card= insmod option to kraxel at bytesex
>>>.org
> 
> 
>>I think that one has a new PCI ID, It has a silicon tuner.. ? can you do 
>>an lspci -vv and post the PCI ID ?
>>Some blown EEPROM's also give wrong PCI ID though..
> 
> 
> 
> here's the output "lspci -vv":
> 
> 0000:01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capt
> ure (rev 11)
>         Subsystem: Unknown device 00a0:bcf8
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
> ping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
> - <MAbort- >SERR- <PERR-
>         Latency: 64 (4000ns min, 10000ns max)
>         Interrupt: pin A routed to IRQ 19
>         Region 0: Memory at f8001000 (32-bit, prefetchable)
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
> -,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 0000:01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (r
> ev 11)
>         Subsystem: Unknown device 00a0:bcf8
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
> ping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort
> - <MAbort- >SERR- <PERR-
>         Latency: 64 (1000ns min, 63750ns max)
>         Interrupt: pin A routed to IRQ 19
>         Region 0: Memory at f8000000 (32-bit, prefetchable)
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
> -,D3cold-)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
>>This looks like a new version of the VP-1030A.. The 1032A is not out in 
>>the market though.. ? Can you verify what VP-10XXX it is , such that it 
>>can be confirmed ?
> 
> 
> The card was bought approximately half a year ago. I'll check this on
> Monday, because the server's located at the office.

If it is an old (Vision Plus) card, probably chances are that the EEPROM 
is not functioning and a bad PCI ID rather than a new card..

I will verify that in a couple of days..

Manu





More information about the linux-dvb mailing list