[linux-dvb] Pctv 300i no analog channels found (with no error messages)

[wolfgang pauli]

Hi, 
 
Well, I did not do a thing, but it works now. Seems like this card needs 
some hours of warm up before the first run, or irqs were changed after 
rebooting. 
 
I have the following prob related modules loaded (I have a second card in 
another pci slot): 
 
btcx-risc 
bttv 
msp3400 
tda9887 
tuner          + BT848 Video für Linux                                      
                  
tvaudio        + BT848 Video For Linux                                      
          
tveeprom       + (No description available) 
v4l1-compat    + (No description available)                                 
                 
v4l2-common    + (No description available) 
video-buf 
videodev 
saa7134 
 
Thank you for the suggestions. 
 
Wolfgang 
 
> --- Ursprüngliche Nachricht --- 
> Von: tim0m1a <tim0m1a at gmx.de> 
> An: "wolfgang pauli" <ookami at gmx.de>, linux-dvb at linuxtv.org 
> Betreff: Re: [linux-dvb] Pctv 300i no analog channels found (with no 
error 
> messages) 
> Datum: Fri, 23 Sep 2005 18:39:40 +0200 
>  
> Am Fri, 23 Sep 2005 17:54:42 +0200 (MEST) schrieb wolfgang pauli   
> <ookami at gmx.de>: 
>  
> > Hi, 
> > I got this stupid card today and it does not find any channels. I am 
> > using "modprobe saa7134 card=26 tuner=33" and get this dmesg output 
> > saa7130/34: v4l2 driver version 0.2.12 loaded 
> > ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 19 (level, high) -> IRQ 
201 
> > saa7134[0]: found at 0000:01:07.0, rev: 1, irq: 201, latency: 32, 
mmio: 
> > 0xd8001000 
> > saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV Stereo 
(saa7134) 
> > [card=26,insmod option] 
> > saa7134[0]: board init: gpio is c806000 
> > tuner: chip found at addr 0xc0 i2c-bus saa7134[0] 
> > tuner: type set to 33 (MT20xx universal) by saa7134[0] 
> > tuner: microtune: companycode=3cbf part=42 rev=8f 
> > tuner: microtune MT2050 found, OK 
> > tda9885/6/7: chip found @ 0x86 
> > saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 
b2 
> > 92 
> > saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff 
ff 
> > ff 
> > saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff 
ff 
> > ff 
> > saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
ff 
> > ff 
> > saa7134[0]: registered device video0 [v4l2] 
> > saa7134[0]: registered device vbi0 
> > Seems OK to me. But it does not find any channels. It can not be the 
> > antenna, because it was working with the old card. I saw 100s of msgs 
> > about this problem, but none helped me or was solved. ANy 
suggestions? 
> > Thank you!!! 
> > 
>  
> Oups. 
> I did not realize that you want to recive analog channels as I did not   
> expect a question about analog video in a dvb mailing list. 
>  
> If you use modprobe the card would be auto detected, so you do not need 
to 
>   
> select a card type. 
>  
> The gentoo-wiki entry explains how you can use the card with dvb-t. I   
> never tried to use the card with analog channels. 
>  
> Regards, 
> Tim 
>  
>  
> --  
> Erstellt mit Operas revolutionärem E-Mail-Modul: 
http://www.opera.com/m2/ 
>  
 

-- 
5 GB Mailbox, 50 FreeSMS http://www.gmx.net/de/go/promail
+++ GMX - die erste Adresse für Mail, Message, More +++