[linux-dvb] Second tuner on Fusion Dual Digital
lkidd at bigpond.net.au
lkidd at bigpond.net.au
Mon Feb 20 10:00:38 CET 2006
Hi Stephen,
OK, I can feel a moment of clarity coming here...what usb cable :-) ? Oh you are kidding me ?!? Just checked the Dvico website and there is a lovely pic showing what has to happen. The manual doesn't show that...
Thanks very much for all the help guys....<sound of my palm smacking my forehead>
Regards
Lachlan
---- Collier Family <judithc at bigpond.net.au> wrote:
> Lachlan,
>
> I hope the USB cable is plugged in - it was the first mistake I made. I
> don't see the USB side of the card in your logs such as below
>
> Feb 14 18:42:26 mythmaster kernel: dvb-usb: found a 'DViCO FusionHDTV DVB-T
> Dual USB' in cold state, will try to load a firmware
>
>
> -Stephen Collier
>
>
> ----- Original Message -----
> From: "Lachlan Kidd" <lkidd at bigpond.net.au>
> To: <linux-dvb at linuxtv.org>; <mkrufky at gmail.com>
> Sent: Monday, February 20, 2006 7:16 PM
> Subject: Re: [linux-dvb] Second tuner on Fusion Dual Digital
>
>
> > Thanks for the response Mike. I've tried those steps and still no joy.
> > I can't see anything in the logs (/var/log/messages or dmesg) about the
> > second tuner or the firmware. From others posts, I think I should see
> > something about the driver going looking for the fw. Is this correct ? Is
> > there a specific module which needs to be loaded ?
> > I'm running 2.6.15
> > Thanks again, Regards
> > Lachlan
> >
> > lsmod
> > Module Size Used by
> > dvb_usb_cxusb 16516 0
> > dvb_usb 19848 1 dvb_usb_cxusb
> > parport_pc 28612 1
> > lp 13512 0
> > parport 37064 2 parport_pc,lp
> > autofs4 20996 0
> > eeprom 7568 0
> > it87 21284 0
> > hwmon_vid 2944 1 it87
> > i2c_isa 5504 1 it87
> > sunrpc 153916 1
> > xfs 579016 1
> > exportfs 6784 1 xfs
> > dm_mod 60824 0
> > video 16004 0
> > button 6928 0
> > battery 9732 0
> > ac 5124 0
> > nvidia 4090832 12
> > ipv6 262880 20
> > ohci1394 35380 0
> > ieee1394 303448 1 ohci1394
> > ohci_hcd 22148 0
> > ehci_hcd 35336 0
> > cx88_blackbird 20508 0
> > cx8800 33676 1 cx88_blackbird
> > compat_ioctl32 1280 1 cx8800
> > v4l1_compat 12932 1 cx8800
> > v4l2_common 15744 2 cx88_blackbird,cx8800
> > i2c_nforce2 7168 0
> > cx88_dvb 12292 0
> > cx8802 12292 2 cx88_blackbird,cx88_dvb
> > cx88xx 61860 4 cx88_blackbird,cx8800,cx88_dvb,cx8802
> > ir_common 27140 1 cx88xx
> > btcx_risc 5000 3 cx8800,cx8802,cx88xx
> > tveeprom 14992 1 cx88xx
> > videodev 10112 3 cx88_blackbird,cx8800,cx88xx
> > cx88_vp3054_i2c 4352 1 cx88_dvb
> > i2c_algo_bit 9352 2 cx88xx,cx88_vp3054_i2c
> > mt352 6660 2 dvb_usb_cxusb,cx88_dvb
> > or51132 9860 1 cx88_dvb
> > video_buf_dvb 6788 1 cx88_dvb
> > dvb_core 84008 2 dvb_usb,video_buf_dvb
> > video_buf 22276 6
> > cx88_blackbird,cx8800,cx88_dvb,cx8802,cx88xx,video_buf_dvb
> > nxt200x 14468 1 cx88_dvb
> > cx24123 9220 1 cx88_dvb
> > lgdt330x 7964 2 dvb_usb_cxusb,cx88_dvb
> > cx22702 6660 2 dvb_usb_cxusb,cx88_dvb
> > i2c_core 22144 15
> > dvb_usb,eeprom,it87,i2c_isa,i2c_nforce2,cx88_dvb,cx88xx,tveeprom,i2c_algo_bit,mt352,or51132,nxt200x,cx24123,lgdt330x,cx22702
> > dvb_pll 11908 6
> > dvb_usb_cxusb,dvb_usb,cx88_dvb,or51132,nxt200x,cx22702
> > snd_intel8x0 32924 0
> > snd_ac97_codec 91040 1 snd_intel8x0
> > snd_ac97_bus 2688 1 snd_ac97_codec
> > snd_pcm_oss 53664 0
> > snd_mixer_oss 19072 1 snd_pcm_oss
> > snd_pcm 93444 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
> > snd_timer 26500 1 snd_pcm
> > snd 58084 6
> > snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
> > soundcore 10336 1 snd
> > snd_page_alloc 11272 2 snd_intel8x0,snd_pcm
> > forcedeth 24580 0
> > floppy 63556 0
> > ext3 135688 2
> > jbd 61204 1 ext3
> >
> > Feb 20 18:26:22 localhost kernel: Linux video capture interface: v1.00
> > Feb 20 18:26:22 localhost kernel: cx2388x dvb driver version 0.0.5 loaded
> > Feb 20 18:26:22 localhost kernel: CORE cx88[0]: subsystem: 18ac:db50,
> > board: DViCO FusionHDTV DVB-T Dual Digita
> > l [card=44,autodetected]
> > Feb 20 18:26:22 localhost kernel: TV tuner 4 at 0x1fe, Radio tuner -1 at
> > 0x1fe
> > Feb 20 18:26:22 localhost kernel: ACPI: PCI Interrupt Link [LNK3] enabled
> > at IRQ 12
> > Feb 20 18:26:22 localhost kernel: PCI: setting IRQ 12 as level-triggered
> > Feb 20 18:26:22 localhost kernel: ACPI: PCI Interrupt 0000:01:06.2[A] ->
> > Link [LNK3] -> GSI 12 (level, low) ->
> > IRQ 12
> > Feb 20 18:26:22 localhost kernel: cx88[0]/2: found at 0000:01:06.2, rev:
> > 5, irq: 12, latency: 32, mmio: 0xdf000
> > 000
> > Feb 20 18:26:22 localhost kernel: cx88[0]/2: cx2388x based dvb card
> > Feb 20 18:26:22 localhost kernel: DVB: registering new adapter (cx88[0]).
> > Feb 20 18:26:22 localhost kernel: DVB: registering frontend 0 (Zarlink
> > MT352 DVB-T)...
> > Feb 20 18:26:22 localhost kernel: i2c_adapter i2c-1: nForce2 SMBus adapter
> > at 0x5000
> > Feb 20 18:26:22 localhost kernel: i2c_adapter i2c-2: nForce2 SMBus adapter
> > at 0x5100
> > Feb 20 18:26:22 localhost kernel: cx2388x v4l2 driver version 0.0.5 loaded
> > Feb 20 18:26:22 localhost kernel: ACPI: PCI Interrupt 0000:01:06.0[A] ->
> > Link [LNK3] -> GSI 12 (level, low) ->
> > IRQ 12
> > Feb 20 18:26:22 localhost kernel: cx88[0]/0: found at 0000:01:06.0, rev:
> > 5, irq: 12, latency: 32, mmio: 0xde000
> > 000
> > Feb 20 18:26:22 localhost kernel: cx88[0]/0: registered device video0
> > [v4l2]
> > Feb 20 18:26:22 localhost kernel: cx88[0]/0: registered device vbi0
> > Feb 20 18:26:22 localhost kernel: set_control id=0x980900 reg=0x310110
> > val=0x00 (mask 0xff)
> > Feb 20 18:26:22 localhost kernel: set_control id=0x980901 reg=0x310110
> > val=0x3f00 (mask 0xff00)
> > Feb 20 18:26:22 localhost kernel: set_control id=0x980903 reg=0x310118
> > val=0x00 (mask 0xff)
> > Feb 20 18:26:22 localhost xinetd[3697]: xinetd Version 2.3.13 started with
> > libwrap loadavg options compiled in.
> > Feb 20 18:26:22 localhost kernel: set_control id=0x980902 reg=0x310114
> > val=0x5a7f (mask 0xffff)
> >
> > lspci
> > 00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?)
> > (rev a2)
> > 00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev
> > a2)
> > 00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev
> > a2)
> > 00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev
> > a2)
> > 00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev
> > a2)
> > 00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev
> > a2)
> > 00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a3)
> > 00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
> > 00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3)
> > 00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3)
> > 00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3)
> > 00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
> > Controller (rev a1)
> > 00:05.0 Multimedia audio controller: nVidia Corporation nForce MultiMedia
> > audio [Via VT82C686B] (rev a2)
> > 00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio
> > Controler (MCP) (rev a1)
> > 00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev
> > a3)
> > 00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
> > 00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire (IEEE
> > 1394) Controller (rev a3)
> > 00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev a2)
> > 01:06.0 Multimedia video controller: Conexant Winfast TV2000 XP (rev 05)
> > 01:06.2 Multimedia controller: Conexant: Unknown device 8802 (rev 05)
> > 02:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX -
> > nForce GPU] (rev a3)
> > [root at localhost ~]#
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > On 2/18/06, lkidd at bigpond.net.au <lkidd at bigpond.net.au> wrote:
> >
> > >> Hello,
> > >> I've been reading on this list that a few people have had some success
> > >> in getting both tuners
> > going. Is there any chance on posting a how-to on what was required ? I've
> > got the first tuner going no probs and love it. The second tuner is
> > causing some greif. From what I've read, I've downloaded the firmware, and
> > loaded dvb_usb_cxusb and dvb_usb . Somewhat of a concern is the both
> > dmesg and var/log/messages are very quite about the whole thing. The
> > modules load but nothing else is repored. Also, what /dev entry does the
> > usb tuner show up under ?
> > >> Thanks, Regards
> > >> Lachlan
> >
> >
> > 1) install mercurial
> > 2) hg clone http://linuxtv.org/hg/v4l-dvb
> > 3) cd v4l-dvb
> > 4) linux/Documentation/dvb/get_dvb_firmware bluebird
> > 5) mv dvb-usb-bluebird-01.fw /usr/lib/hotplug/firmware/
> > 6) make
> > 7) make install
> > 8) reboot
> >
> > I hope this helps,
> > Mike
> >
> >
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb at linuxtv.org
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
>
More information about the linux-dvb
mailing list