[linux-dvb] Avermedia DVB-T 771 mt352_read_register error

Paul Wheeler paulrwheeler at gmail.com
Mon Jan 30 15:16:15 CET 2006


Michael,

I have had multiple dvb 771 cards. Many started working then stopped.
I have swapped them back and got replacements which have worked for a
bit then stopped. I have one card that works all the time and another
that now fails to work. I can plug either into the same pci slot with
exactly the same setup one will work the other wont. (the one that
doesnt still works in other pcs!). I in the end gave up and switched
to the nova-t. My motherboard was also an asus P7P800S-X I think. The
funny thing was that the powersupply change also made a difference (I
can change the power supply and it will start working again,
unfortunately the power supply that works doesnt fit in my case and is
noisey).

My Verdict - A random bug (prob from a hardware/software race
condition somewhere) stops the card from working 100% of the time. The
bug is unlikely to get fixed due to the fact it is very difficult to
repeat unless you have the exact hardware setup that causes it. I
switched cards and sold the other on ebay.

It is a shame as i liked the 771 and find it has better reception than
the nova-t. I would recommend switching to a nova-t and putting myth
tv on it. ( I have had a bug with compiled in drivers for both cards
if you run a dual tuner system, see previous posts)

Paul

On 1/25/06, Michael Carter <mjcarter at btconnect.com> wrote:
> Hi,
> I'm hoping someone here can help me with this problem - I seem to have
> trawled through tons of archived posts trying all suggestions but have
> had no success.
>
> When attempting to load the dvb-bt8xx module for my AverMedia 771 DVB-T
> card I get the following error in my dmesg output:
>
> DVB: registering new adapter (bttv0).
> mt352_read_register: readreg error (reg=127, ret==-5)
> dvb-bt8xx: A frontend driver was not found for device 109e/0878
> subsystem 1461/0771
>
> The card is currently plugged into an Asus A7S8X-MX motherboard but I
> have the same problem on my Abit VA-20 motherboard (both Socket-A AMD
> 462 MicroATX). After doing hours of fiddling around I have noticed that
> removing the GeForce MX 4000 card from the AGP slot will allow the
> driver to load.
>
> I have tried the following but to no avail, the only thing that works is
> removing the NVidia card from the AGP slot (which I need for TV-Out etc):
>
> - Reseated the card in the same PCI slot
> - Tried the card in every other PCI slot on both mobos
> - Tried standard Fedora Core 4 kernels (2.6.11-1.1369_FC4 and
> 2.6.14-1.1656_FC4)- Compiled custom kernel from kernel.org with patches
> from linuxtv.org (2.6.12)
> - Booted machine with kernel parameters pci=noacpi, pci=routeirq as well
> as manyothers as suggested in previous postings.
> - Booted with Plug&Play OS option in BIOS both enabled and disabled.
> - Tried an two alternate (perfectly functioning) AGP cards (both recent
> NVidia) and still get the error.
> - Disabled *every* piece of onboard hardware in the BIOS, just run with
> Avermedia card and Nvidia AGP cardi, with no success.
>
> I am completely at a loss and would really appreciate any help, I've
> tried all I can think of! Must also say that the DVB-T card works
> perfectly in my main system (Asus A8V Deluxe Socket 939) with both the
> Fedora Core kernels mentioned above, the only thing I can think of is
> thats its a mobo/BIOS problem or something within the mt352 driver.
>
> Full dmesg output:
>
> Linux version 2.6.12.1 (root at chronos) (gcc version 4.0.0 20050519 (Red
> Hat 4.0.0-8)) #1 Tue Jan 10 22:50:26 GMT 2006
> BIOS-provided physical RAM map:
>  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
>  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
>  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
>  BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
>  BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
>  BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
>  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
>  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
>  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> 0MB HIGHMEM available.
> 511MB LOWMEM available.
> On node 0 totalpages: 131056
>   DMA zone: 4096 pages, LIFO batch:1
>   Normal zone: 126960 pages, LIFO batch:31
>   HighMem zone: 0 pages, LIFO batch:1
> DMI 2.3 present.
> ACPI: RSDP (v000 AWARD                                 ) @ 0x000f7730
> ACPI: RSDT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
> ACPI: FADT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
> ACPI: MADT (v001 AWARD  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff6a40
> ACPI: DSDT (v001 AWARD  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
> ACPI: PM-Timer IO Port: 0x1008
> Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
> Built 1 zonelists
> Kernel command line: ro root=LABEL=/1 rhgb quiet pci=noacpi
> Initializing CPU#0
> CPU 0 irqstacks, hard=c047b000 soft=c047a000
> PID hash table entries: 2048 (order: 11, 32768 bytes)
> Detected 1584.090 MHz processor.
> Using pmtmr for high-res timesource
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 513568k/524224k available (2661k kernel code, 10028k reserved,
> 679k data, 192k init, 0k highmem)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay loop... 3145.72 BogoMIPS (lpj=1572864)
> Security Framework v1.0.0 initialized
> SELinux:  Initializing.
> SELinux:  Starting in permissive mode
> selinux_register_security:  Registering secondary module capability
> Capability LSM initialized as secondary
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000
> 00000000 00000000 00000000
> CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000
> 00000000 00000000 00000000
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000
> 00000000 00000000
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: AMD Sempron(tm)   2300+ stepping 01
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Checking 'hlt' instruction... OK.
> checking if image is initramfs... it is
> Freeing initrd memory: 1194k freed
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xfbce0, last bus=1
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20050309
> ACPI: Interpreter enabled
> ACPI: Using PIC for interrupt routing
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 11 devices
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
> Boot video device is 0000:01:00.0
> PCI: Using IRQ router SIS [1039/0964] at 0000:00:02.0
> PCI: IRQ 0 for device 0000:00:02.5 doesn't match PIRQ mask - try
> pci=usepirqmaskPCI: Found IRQ 5 for device 0000:00:02.5
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
> apm: overridden by ACPI.
> audit: initializing netlink socket (disabled)
> audit(1137374389.834:0): initialized
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> SELinux:  Registering netfilter hooks
> Initializing Cryptographic API
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> ACPI: Fan [FAN] (on)
> ACPI: Thermal Zone [THRM] (58 C)
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected SiS 741 chipset
> agpgart: AGP aperture is 64M @ 0xe8000000
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> SIS5513: IDE controller at PCI slot 0000:00:02.5
> PCI: Found IRQ 5 for device 0000:00:02.5
> SIS5513: chipset revision 1
> SIS5513: not 100% native mode: will probe irqs later
> SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
>     ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
>     ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:pio, hdd:pio
> Probing IDE interface ide0...
> hda: WDC WD2000JB-00GVC0, ATA DISK drive
> hdb: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> Probing IDE interface ide1...
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Probing IDE interface ide4...
> Probing IDE interface ide5...
> hda: max request size: 1024KiB
> hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63,
> UDMA(100)
> hda: cache flushes supported
>  hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
> hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> ide-floppy driver 0.99.newide
> usbcore: registered new driver hiddev
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> NET: Registered protocol family 2
> input: AT Translated Set 2 keyboard on isa0060/serio0
> IP: routing cache hash table of 1024 buckets, 32Kbytes
> TCP established hash table entries: 32768 (order: 6, 262144 bytes)
> TCP bind hash table entries: 32768 (order: 7, 917504 bytes)
> TCP: Hash tables configured (established 32768 bind 32768)
> Initializing IPsec netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> ACPI wakeup devices:
> FUTS PCI0 USB0 USB1 USB2 USB3 MAC0 AMR0 UAR1 PS2M PS2K
> ACPI: (supports S0 S3 S4 S5)
> Freeing unused kernel memory: 192k freed
> SCSI subsystem initialized
> libata version 1.11 loaded.
> input: PS/2 Generic Mouse on isa0060/serio1
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> SELinux:  Disabled at runtime.
> SELinux:  Unregistering netfilter hooks
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> sis900.c: v1.08.08 Jan. 22 2005
> PCI: Found IRQ 10 for device 0000:00:04.0
> 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
> 0000:00:04.0: Using transceiver found at address 1 as default
> eth0: SiS 900 PCI Fast Ethernet at 0xe800, IRQ 10, 00:13:d4:16:2b:0e.
> PCI: Found IRQ 11 for device 0000:00:02.7
> PCI: Sharing IRQ 11 with 0000:00:0a.0
> intel8x0_measure_ac97_clock: measured 49583 usecs
> intel8x0: clocking to 48000
> shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
> shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
> Linux video capture interface: v1.00
> bttv: driver version 0.9.15 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> PCI: Found IRQ 9 for device 0000:00:09.0
> PCI: Sharing IRQ 9 with 0000:00:09.1
> bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 9, latency: 32, mmio: 0xef023000
> bttv0: detected: AVermedia AverTV DVB-T 771 [card=123], PCI subsystem ID
> is 1461:0771
> bttv0: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected]
> bttv0: gpio: en=00000000, out=00000000 in=00fbff9f [init]
> bttv0: using tuner=4
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: PLL: 28636363 => 35468950 .. ok
> bttv0: add subdevice "remote0"
> bttv0: add subdevice "dvb0"
> bt878: AUDIO driver version 0.0.0 loaded
> bt878: Bt878 AUDIO function found (0).
> PCI: Found IRQ 9 for device 0000:00:09.1
> PCI: Sharing IRQ 9 with 0000:00:09.0
> bt878(0): Bt878 (rev 17) at 00:09.1, irq: 9, latency: 32, memory: 0xef024000
> PCI: Found IRQ 11 for device 0000:00:03.3
> ehci_hcd 0000:00:03.3: EHCI Host Controller
> ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.3: irq 11, io mem 0xef020000
> PCI: cache line size of 64 is not supported by device 0000:00:03.3
> ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> PCI: Found IRQ 9 for device 0000:00:03.0
> ohci_hcd 0000:00:03.0: OHCI Host Controller
> ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:00:03.0: irq 9, io mem 0xef022000
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> PCI: Found IRQ 5 for device 0000:00:03.1
> ohci_hcd 0000:00:03.1: OHCI Host Controller
> usb 1-7: new high speed USB device using ehci_hcd and address 2
> ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> ohci_hcd 0000:00:03.1: irq 5, io mem 0xef025000
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 3 ports detected
> PCI: Found IRQ 10 for device 0000:00:03.2
> ohci_hcd 0000:00:03.2: OHCI Host Controller
> ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
> ohci_hcd 0000:00:03.2: irq 10, io mem 0xef026000
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c0408640(lo)
> IPv6 over IPv4 tunneling driver
> nvidia: module license 'NVIDIA' taints kernel.
> NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module  1.0-7676  Fri Jul
> 29 12:58:54 PDT 2005
> agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
> agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
> agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
> agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
> agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
> agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
>   Vendor: USB2.0    Model: CF  CardReader    Rev:
>   Type:   Direct-Access                      ANSI SCSI revision: 00
> Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
>   Vendor: USB2.0    Model: CBO CardReader    Rev:
>   Type:   Direct-Access                      ANSI SCSI revision: 00
> Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
> usb-storage: device scan complete
> ACPI: Power Button (FF) [PWRF]
> ACPI: Sleep Button (CM) [FUTS]
> ibm_acpi: ec object not found
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
> cdrom: open failed.
> cdrom: open failed.
> EXT3 FS on hda2, internal journal
> kjournald starting.  Commit interval 5 seconds
> EXT3 FS on hda1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> JFS: nTxBlock = 4024, nTxLock = 32199
> Adding 1052248k swap on /dev/hda3.  Priority:-1 extents:1
> eth0: Media Link On 100mbps full-duplex
> Bluetooth: Core ver 2.7
> NET: Registered protocol family 31
> Bluetooth: HCI device and connection manager initialized
> Bluetooth: HCI socket layer initialized
> Bluetooth: L2CAP ver 2.7
> Bluetooth: L2CAP socket layer initialized
> Bluetooth: RFCOMM ver 1.5
> Bluetooth: RFCOMM socket layer initialized
> Bluetooth: RFCOMM TTY layer initialized
> parport: PnPBIOS parport detected.
> parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
> lp0: using parport0 (interrupt-driven).
> lp0: console ready
> eth0: no IPv6 routers present
> DVB: registering new adapter (bttv0).
> mt352_read_register: readreg error (reg=127, ret==-5)
> dvb-bt8xx: A frontend driver was not found for device 109e/0878
> subsystem 1461/0771
>
> Output from lspci -v:
>
> [root at chronos ~]# lspci -v
> 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 741/741GX/M741
> Host (rev 03)
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 815c
>         Flags: bus master, medium devsel, latency 32
>         Memory at e8000000 (32-bit, non-prefetchable) [size=64M]
>         Capabilities: [c0] AGP version 3.5
>
> 00:01.0 PCI bridge: Silicon Integrated Systems [SiS]: Unknown device
> 0003 (prog-if 00 [Normal decode])
>         Flags: bus master, 66Mhz, fast devsel, latency 99
>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
>         Memory behind bridge: ec000000-edffffff
>         Prefetchable memory behind bridge: e0000000-e7ffffff
>
> 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL
> Media IO] (rev 36)
>         Flags: bus master, medium devsel, latency 0
>
> 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev
> 01) (prog-if 80 [Master])
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 810e
>         Flags: bus master, medium devsel, latency 128, IRQ 5
>         I/O ports at <unassigned>
>         I/O ports at <unassigned>
>         I/O ports at <unassigned>
>         I/O ports at <unassigned>
>         I/O ports at 4000 [size=16]
>         Capabilities: [58] Power Management version 2
>
> 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
> Sound Controller (rev a0)
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 810d
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at e000 [size=256]
>         I/O ports at e400 [size=128]
>         Capabilities: [48] Power Management version 2
>
> 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 810e
>         Flags: bus master, medium devsel, latency 32, IRQ 9
>         Memory at ef022000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 810e
>         Flags: bus master, medium devsel, latency 32, IRQ 5
>         Memory at ef025000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
> Controller (rev 0f) (prog-if 10 [OHCI])
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 810e
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at ef026000 (32-bit, non-prefetchable) [size=4K]
>
> 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
> Controller (prog-if 20 [EHCI])
>         Subsystem: ASUSTeK Computer Inc.: Unknown device 810e
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         Memory at ef020000 (32-bit, non-prefetchable) [size=4K]
>         Capabilities: [50] Power Management version 2
>
> 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
> Fast Ethernet (rev 90)
>         Subsystem: Silicon Integrated Systems [SiS] SiS900 10/100
> Ethernet Adapter
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         I/O ports at e800 [size=256]
>         Memory at ef021000 (32-bit, non-prefetchable) [size=4K]
>         Capabilities: [40] Power Management version 2
>
> 00:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video
> Capture (rev 11)
>         Subsystem: Avermedia Technologies Inc: Unknown device 0771
>         Flags: bus master, medium devsel, latency 32, IRQ 9
>         Memory at ef023000 (32-bit, prefetchable) [size=4K]
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>
> 00:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture
> (rev 11)
>         Subsystem: Avermedia Technologies Inc: Unknown device 0771
>         Flags: bus master, medium devsel, latency 32, IRQ 9
>         Memory at ef024000 (32-bit, prefetchable) [size=4K]
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>
> 00:0a.0 Ethernet controller: Marvell Technology Group Ltd.: Unknown
> device 1faa (rev 03)
>         Subsystem: Netgear: Unknown device 6b00
>         Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
>         Memory at ef000000 (32-bit, non-prefetchable) [size=64K]
>         Memory at ef010000 (32-bit, non-prefetchable) [size=64K]
>         Capabilities: [40] Power Management version 2
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX
> 4000 AGP 8x] (rev c1) (prog-if 00 [VGA])
>         Subsystem: CardExpert Technology: Unknown device 0422
>         Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 5
>         Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
>         Memory at e0000000 (32-bit, prefetchable) [size=128M]
>         Capabilities: [60] Power Management version 2
>         Capabilities: [44] AGP version 3.0
>
> There are other posts of people with similar problems with the mt352
> frontend for this card - its just that none of the solutions have worked
> for me.
>
> The whole point of this project was to build a low cost linux PVR as a
> side project and I really dont want to have to put Windoze Media Center
> on it or worse still sell the hardware, so any help would be greatly
> received.
>
> Cheers,
> Mike
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>



More information about the linux-dvb mailing list