[linux-dvb] SS2 2.6D: no frontend driver found for this B2C2/FlexCop adapter

[Brendan White]

Yea- i assumed it used stv0299, which is loaded with the b2c2-flexcop 
driver.It just doesnt probe/attach/whatever correctly.
:

% lsmod

<clip>
b2c2_flexcop_pci        8984  0
b2c2_flexcop           25292  1 b2c2_flexcop_pci
mt352                   8580  1 b2c2_flexcop
mt312                   9412  1 b2c2_flexcop
bcm3510                11332  1 b2c2_flexcop
stv0299                12552  1 b2c2_flexcop
dvb_core               81436  2 b2c2_flexcop,stv0299
nxt200x                15300  1 b2c2_flexcop
firmware_class         11008  5 cx25840,tuner,b2c2_flexcop,bcm3510,nxt200x
dvb_pll                13252  2 b2c2_flexcop,nxt200x
stv0297_cs2            11588  1 b2c2_flexcop
lgdt330x                9884  1 b2c2_flexcop
i2c_core               21632  14 
tda9887,wm8775,cx25840,tuner,tveeprom,i2c_algo_                 
bit,b2c2_flexcop,mt352,mt312,bcm3510,stv0299,nxt200x,stv0297_cs2,lgdt330x
<clip>

I'm going to take out my pvr150's, see if thats confusing things.

-brendan

Nico Sabbi wrote:
> Brendan White wrote:
>
>> SkyStar2 TV version 2.6D
>> gentoo amd64
>> 2.6.14
>>
>> I've tried stock 2.6.14 drivers, linuxtv stable snapshot, and the  
>> most recent daily snapshot.  I've tried the card in different 
>> slots.   All yield the same results.  The frontend driver modules do 
>> load,  they just dont seem to do anything useful:
>>
>>
>> b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip  
>> loaded successfully
>> flexcop-pci: will use the HW PID filter.
>> flexcop-pci: card revision 2
>> ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
>> ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC4] -> GSI 19 (level,  
>> low) -> IRQ 66
>> DVB: registering new adapter (FlexCop Digital TV device).
>> b2c2-flexcop: reading of MAC address failed.
>>
>> b2c2-flexcop: i2c master_xfer failed
>> b2c2-flexcop: i2c master_xfer failed
>> b2c2-flexcop: i2c master_xfer failed
>> mt352_read_register: readreg error (reg=127, ret==-121)
>> b2c2-flexcop: i2c master_xfer failed
>> nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
>> Unknown/Unsupported NXT chip: 00 00 00 00 00
>> b2c2-flexcop: i2c master_xfer failed
>> lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret ==  
>> -121)
>> b2c2-flexcop: i2c master_xfer failed
>> b2c2-flexcop: i2c master_xfer failed
>> b2c2-flexcop: i2c master_xfer failed
>> mt312_read: ret == -121
>> b2c2-flexcop: no frontend driver found for this B2C2/FlexCop adapter
>> ACPI: PCI interrupt for device 0000:01:09.0 disabled
>>
>>
> doesn't this card use the stv0299?
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb