[linux-dvb] Q re Nova-T 500 USB bootup messages

Eyal Lebedinsky eyal at eyal.emu.id.au
Fri Apr 20 00:40:50 CEST 2007


I notice some errors reported when the dib0700 is loaded. Are these OK
to ignore?

[   50.462203] usbcore: registered new interface driver usbfs
[   50.487401] usbcore: registered new interface driver hub
[   50.511893] usbcore: registered new device driver usb
[   50.545315] USB Universal Host Controller Interface driver v3.0
[   50.571719] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
[   50.594023] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   50.594027] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   50.618885] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   50.641136] uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000bc00
[   50.665040] usb usb1: configuration #1 chosen from 1 choice
[   50.682311] hub 1-0:1.0: USB hub found
[   50.693596] hub 1-0:1.0: 2 ports detected
[   51.177088] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
[   51.200871] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   51.200875] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   51.217587] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   51.239838] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000b000
[   51.258756] usb usb2: configuration #1 chosen from 1 choice
[   51.275858] hub 2-0:1.0: USB hub found
[   51.287139] hub 2-0:1.0: 2 ports detected
[   51.478663] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
[   51.500984] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   51.500988] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   51.550551] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   51.572786] uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000b400
[   51.809459] usb usb3: configuration #1 chosen from 1 choice
[   51.826689] hub 3-0:1.0: USB hub found
[   51.837976] hub 3-0:1.0: 2 ports detected
[   52.529415] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 17
[   52.551707] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[   52.551710] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   52.575997] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   52.598240] uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000b800
[   52.627186] usb usb4: configuration #1 chosen from 1 choice
[   52.644443] hub 4-0:1.0: USB hub found
[   52.655740] hub 4-0:1.0: 2 ports detected
[   53.845670] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 18 (level, low) -> IRQ 16
[   53.867984] uhci_hcd 0000:03:04.0: UHCI Host Controller
[   53.892254] uhci_hcd 0000:03:04.0: new USB bus registered, assigned bus number 5
[   53.914494] uhci_hcd 0000:03:04.0: irq 16, io base 0x00008c00
[   53.943338] usb usb5: configuration #1 chosen from 1 choice
[   53.960594] hub 5-0:1.0: USB hub found
[   53.971895] hub 5-0:1.0: 2 ports detected
[   54.770872] ACPI: PCI Interrupt 0000:03:04.1[B] -> GSI 21 (level, low) -> IRQ 19
[   54.793191] uhci_hcd 0000:03:04.1: UHCI Host Controller
[   54.811570] uhci_hcd 0000:03:04.1: new USB bus registered, assigned bus number 6
[   54.833834] uhci_hcd 0000:03:04.1: irq 19, io base 0x00009000
[   54.853568] usb usb6: configuration #1 chosen from 1 choice
[   54.871547] hub 6-0:1.0: USB hub found
[   54.882837] hub 6-0:1.0: 2 ports detected
[   55.086936] usb 5-1: new full speed USB device using uhci_hcd and address 2
[   55.262410] usb 5-1: configuration #1 chosen from 1 choice

[   61.956776] dib0700: loaded with support for 2 different device-types
[   61.993148] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state.
	############ errors start
[   62.014577] **WARNING** I2C adapter driver [Hauppauge Nova-T 500 Dual DVB-T] forgot to specify physical device; fix it!
[   62.047514] dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)
[   62.084629] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T error while loading driver (-19)
	############ errors end
[   62.108150] usbcore: registered new interface driver dvb_usb_dib0700

[   64.697710] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
[   64.720027] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   64.720031] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   64.744451] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[   64.766704] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[   64.766714] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xde100000
[   64.787573] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   64.821581] usb usb7: configuration #1 chosen from 1 choice
[   64.838829] hub 7-0:1.0: USB hub found
[   64.850136] hub 7-0:1.0: 8 ports detected
[   65.362275] ACPI: PCI Interrupt 0000:03:04.2[C] -> GSI 22 (level, low) -> IRQ 21
[   65.384578] ehci_hcd 0000:03:04.2: EHCI Host Controller
[   65.408886] ehci_hcd 0000:03:04.2: new USB bus registered, assigned bus number 8
[   65.431146] ehci_hcd 0000:03:04.2: irq 21, io mem 0xdd025000
[   65.448131] ehci_hcd 0000:03:04.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   65.482075] usb usb8: configuration #1 chosen from 1 choice
[   65.499330] hub 8-0:1.0: USB hub found
[   65.510636] hub 8-0:1.0: 4 ports detected
[   65.540000] usb 5-1: USB disconnect, address 2
[   66.008950] usb 8-1: new high speed USB device using ehci_hcd and address 2
[   66.145224] usb 8-1: configuration #1 chosen from 1 choice
[   66.161913] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state.
[   66.183326] **WARNING** I2C adapter driver [Hauppauge Nova-T 500 Dual DVB-T] forgot to specify physical device; fix it!
[   66.216239] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   66.241510] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T).
[   66.326605] **WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it!
[   66.357545] DVB: registering frontend 0 (DiBcom 3000MC/P)...
[   66.397349] MT2060: successfully identified (IF1 = 1220)
[   66.838135] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   66.863566] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T).
[   66.886794] **WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it!
[   66.917742] DVB: registering frontend 1 (DiBcom 3000MC/P)...
[   66.936827] MT2060: successfully identified (IF1 = 1220)
[   67.380734] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T successfully initialized and connected.

-- 
Eyal Lebedinsky (eyal at eyal.emu.id.au) <http://samba.org/eyal/>
	attach .zip as .dat



More information about the linux-dvb mailing list