[linux-dvb] Suggestions for T750
mrechberger at gmail.com
Tue Apr 24 13:01:15 CEST 2007
On 4/24/07, John Newbigin <jnewbigin at optusnet.com.au> wrote:
> Markus Rechberger wrote:
> > Hi,
> > did you see the existing xc3028 driver on mcentral.de?
> > http://mcentral.de/hg/~mrec/v4l-dvb-experimental/
> > xc3028-tuner.c (it's implemented in the em28xx, saa7134 and cx88 there)
> I xc3028 code I have seen is tied to the em28xx driver. Are there any
> instructions for using this experimental code? I am currently working off
the experimental tree is just the same as
http://linuxtv.org/hg/v4l-dvb it just includes support for around 60
(just replace http://linuxtv.org/hg/v4l-dvb with
The code isn't tied to the em28xx in the experimental tree (it's used
with cx88, saa7134 and em28xx)
Best would be to look at em2880-dvb how it's implemented there.
the installation instruction for em28xx based devices should also
apply for your version.
> I have the correct firmware for this card but I don't know how to
> 'package' it to work with the 3028 driver.
> Where possible I certainly want to use reuse the existing code.
> The T750 is a SAA7134(5) based PCI card. The card also has digital
> based on the XL10353 and QT1010.
> > That driver supports xc3028, xc2028, xc3018 chips, you might have some
> > issues with the firmwares, best would be to try existing packages.
> > What kind of device is that?
> > PCI/Conexant, or something else?
> > Markus
> > On 4/23/07, John Newbigin <jnewbigin at optusnet.com.au> wrote:
> >> Here I go replying to myself again.
> >> I have had some success with loading the firmware. I has a suspicion
> >> that I needed to twiddle the GPIO pins but could not get it to work.
> >> Studying the xc3028 driver showed me the way. The GPIO needs to be
> >> first cleared and then set before continuing.
> >> The xc3028 is very similar to the xc2028 and they could use a common
> >> driver. I don't understand how the firmware file is stored for the
> >> xc3028 though. I assume that multiple chunks are encoded into one file
> >> somehow.
> >> There is also another firmware chunk which is needed for FM radio
> >> support so I don't know how that would be added.
> >> Anyway, I have loading firmware but still no TV. I think I am close
> >> though.
> >> i2c traces and firmware can be downloaded from here
> >> http://www.chrysocome.net/downloads/t750-logs-0.1.tar.gz
> >> I'll try and clean up my code and post a patch tomorrow.
> >> John.
> >> John Newbigin wrote:
> >> > I have made some slow progress with the T750. I have implemented
> >> > loading the firmware for the CX2028 but I have hit a problem.
> >> >
> >> > After loading the firmware, there are some commands (known as the
> >> > 'MAGIC VALUES') which need to be issued. These are the same as for
> >> > the CX3028. After this final write, my card does another write and
> >> > then a read, but when I attempt the final read command the chip locks
> >> > up and returns BUSY.
> >> >
> >> > Once this happens, the card has to be powered off to reset everything.
> >> >
> >> > Can anyone offer some suggestions of things to try. I have the
> >> > feeling I am very close.
> >> >
> >> > I have i2c traces if anyone wants to see them but they are quite
> >> large.
> >> >
> >> > John.
> >> >
> >> > _______________________________________________
> >> > linux-dvb mailing list
> >> > linux-dvb at linuxtv.org
> >> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >> >
> >> _______________________________________________
> >> linux-dvb mailing list
> >> linux-dvb at linuxtv.org
> >> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
More information about the linux-dvb