[linux-dvb] HVR 4000 under http://linuxtv.org/hg/~hverkuil/v4l-dvb2

Gregoire Favre Gregoire.Favre at gmail.com
Wed Feb 7 17:32:05 CET 2007


Hello,

just tried this source, and it claim my card isn't known, see dmesg
output.

What shall I do ?

Thank you very much,
-- 
Grégoire FAVRE  http://gregoire.favre.googlepages.com  http://www.gnupg.org
-------------- next part --------------
Linux version 2.6.20 (greg at ar) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 PREEMPT Sun Feb 4 22:45:55 CET 2007
Command line: root=/dev/sdb2 elevator=cfq vga=0x507
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d6000 - 00000000000e0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
 BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 262128) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.3 present.
ACPI: RSDP (v000 AMI                                   ) @ 0x00000000000fa0c0
ACPI: RSDT (v001 AMIINT VIA_K8   0x00000010 MSFT 0x00000097) @ 0x000000003fff0000
ACPI: FADT (v001 AMIINT VIA_K8   0x00000011 MSFT 0x00000097) @ 0x000000003fff0030
ACPI: MADT (v001 AMIINT VIA_K8   0x00000009 MSFT 0x00000097) @ 0x000000003fff00c0
ACPI: DSDT (v001    VIA   VIA_K8 0x00001000 MSFT 0x0100000d) @ 0x0000000000000000
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 262128) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   262128
On node 0 totalpages: 262031
  DMA zone: 56 pages used for memmap
  DMA zone: 1159 pages reserved
  DMA zone: 2784 pages, LIFO batch:0
  DMA32 zone: 3527 pages used for memmap
  DMA32 zone: 254505 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000d6000
Nosave address range: 00000000000d6000 - 00000000000e0000
Nosave address range: 00000000000e0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists.  Total pages: 257289
Kernel command line: root=/dev/sdb2 elevator=cfq vga=0x507
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2000.142 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ d0000000 size 256 MB
Memory: 1027168k/1048512k available (3102k kernel code, 20580k reserved, 1032k data, 184k init)
Calibrating delay using timer specific routine.. 4004.53 BogoMIPS (lpj=6671251)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12500904
Detected 12.500 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xd0000000
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: bde00000-bfefffff
  PREFETCH window: 9dd00000-bdcfffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
SGI XFS with large block/inode numbers, no debug enabled
io scheduler noop registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xa0000000, mapped to 0xffffc20000180000, using 2560k, total 262144k
vesafb: mode is 1280x1024x8, linelength=1280, pages=1
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: RTL8169s/8110s at 0xffffc2000001ad00, 00:0c:76:bd:22:23, IRQ 16
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
        <Adaptec 29160 Ultra160 SCSI adapter>
        aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs

sata_via 0000:00:0f.0: version 2.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xD400 irq 20
ata2: SATA max UDMA/133 cmd 0xDC00 ctl 0xD802 bmdma 0xD408 irq 20
scsi1 : sata_via
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ATA: abnormal status 0x7F on port 0xE407
ATA: abnormal status 0x7F on port 0xE407
ata1.00: ATA-7, max UDMA/133, 398297088 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi2 : sata_via
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xDC07
scsi: waiting for bus probes to complete ...
scsi 0:0:15:0: Direct-Access     SEAGATE  ST336706LW       0108 PQ: 0 ANSI: 3
scsi0:A:15:0: Tagged Queuing enabled.  Depth 253
 target0:0:15: Beginning Domain Validation
 target0:0:15: wide asynchronous
 target0:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
 target0:0:15: Ending Domain Validation
SCSI device sda: 71687370 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: 9f 00 10 08
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sda: 71687370 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: 9f 00 10 08
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1 sda2
sd 0:0:15:0: Attached scsi disk sda
sd 0:0:15:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access     ATA      Maxtor 6B200M0   BANC PQ: 0 ANSI: 5
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
pata_via 0000:00:0f.1: version 0.2.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
ata3: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFC00 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xFC08 irq 15
scsi3 : pata_via
ata3.00: ATA-5, max UDMA/100, 241254720 sectors: LBA 
Losing some ticks... checking if CPU frequency changed.
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/100
scsi4 : pata_via
ata4.00: ATAPI, max UDMA/66
ata4.01: ATAPI, max UDMA/33
ata4.00: configured for UDMA/66
ata4.01: configured for UDMA/33
scsi 3:0:0:0: Direct-Access     ATA      IC35L120AVVA07-0 VA6O PQ: 0 ANSI: 5
SCSI device sdc: 241254720 512-byte hdwr sectors (123522 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdc: 241254720 512-byte hdwr sectors (123522 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc1 sdc2 sdc3 sdc4
sd 3:0:0:0: Attached scsi disk sdc
sd 3:0:0:0: Attached scsi generic sg2 type 0
scsi 4:0:0:0: CD-ROM            LITE-ON  DVDRW SHW-1635S  YS0Z PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 125x/125x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
sr 4:0:0:0: Attached scsi generic sg3 type 5
scsi 4:0:1:0: CD-ROM            SONY     DVD RW DRU-500A  2.1a PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
sr 4:0:1:0: Attached scsi CD-ROM sr1
sr 4:0:1:0: Attached scsi generic sg4 type 5
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 21, io mem 0xcfffeb00
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-4: new high speed USB device using ehci_hcd and address 3
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000cc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-4: configuration #1 chosen from 1 choice
hub 1-4:1.0: USB hub found
hub 1-4:1.0: 2 ports detected
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
usb 1-4.1: new high speed USB device using ehci_hcd and address 4
usb 1-4.1: configuration #1 chosen from 1 choice
hub 1-4.1:1.0: USB hub found
hub 1-4.1:1.0: 4 ports detected
usb 1-4.2: new high speed USB device using ehci_hcd and address 5
usb 1-4.2: configuration #1 chosen from 1 choice
usb 3-1.1: new low speed USB device using uhci_hcd and address 3
usb 3-1.1: configuration #1 chosen from 1 choice
usb 3-1.4: new full speed USB device using uhci_hcd and address 4
usb 3-1.4: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech Logitech Gaming Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [Logitech Logitech Gaming Keyboard] on usb-0000:00:10.1-1.1
input: Logitech Logitech Gaming Keyboard as /class/input/input1
input,hiddev96: USB HID v1.10 Device [Logitech Logitech Gaming Keyboard] on usb-0000:00:10.1-1.1
input: G15 Keyboard G15 Keyboard as /class/input/input2
input,hiddev97: USB HID v1.11 Keypad [G15 Keyboard G15 Keyboard] on usb-0000:00:10.1-1.4
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input3
input: PC Speaker as /class/input/input4
logips2pp: Detected unknown logitech mouse model 105
input: ImExPS/2 Logitech Explorer Mouse as /class/input/input5
Advanced Linux Sound Architecture Driver Version 1.0.14rc1 (Tue Jan 09 09:56:17 2007 UTC).
ALSA device list:
  No soundcards found.
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (version 2.00.00)
powernow-k8:    0 : fid 0x2 (1000 MHz), vid 0x12
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x6
powernow-k8:    2 : fid 0xc (2000 MHz), vid 0x2
ACPI: (supports S0 S3 S4 S5)
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ReiserFS: sdb2: found reiserfs format "3.6" with standard journal
ReiserFS: sdb2: using ordered data mode
ReiserFS: sdb2: journal params: device sdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb2: checking transaction log (sdb2)
ReiserFS: sdb2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 184k freed
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
Linux video capture interface: v2.00
Initializing USB Mass Storage driver...
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
saa7146: register extension 'budget_ci dvb'.
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
cx2388x alsa driver version 0.0.6 loaded
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 18
saa7146: found saa7146 @ mem ffffc2000007ce00 (revision 1, irq 18) (0x13c2,0x100f).
saa7146 (0): dma buffer size 192512
DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI).
cx2388x v4l2 driver version 0.0.6 loaded
adapter has MAC addr = 00:d0:5c:23:a3:9b
input: Budget-CI dvb ir receiver saa7146 (0) as /class/input/input6
DVB: registering frontend 0 (ST STV0299 DVB-S)...
CORE cx88[0]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
nvidia: module license 'NVIDIA' taints kernel.
cx88[0]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:00:05.2[A] -> GSI 16 (level, low) -> IRQ 16
cx88[0]/2: found at 0000:00:05.2, rev: 3, irq: 16, latency: 32, mmio: 0xce000000
cx88[1]: Your board isn't known (yet) to the driver.  You can
cx88[1]: try to pick one of the existing card configs via
cx88[1]: card=<n> insmod option.  Updating to the latest
cx88[1]: version might help as well.
cx88[1]: Here is a list of valid choices for the card=<n> insmod option:
cx88[1]:    card=0 -> UNKNOWN/GENERIC
cx88[1]:    card=1 -> Hauppauge WinTV 34xxx models
cx88[1]:    card=2 -> GDI Black Gold
cx88[1]:    card=3 -> PixelView
cx88[1]:    card=4 -> ATI TV Wonder Pro
cx88[1]:    card=5 -> Leadtek Winfast 2000XP Expert
cx88[1]:    card=6 -> AverTV Studio 303 (M126)
cx88[1]:    card=7 -> MSI TV- at nywhere Master
cx88[1]:    card=8 -> Leadtek Winfast DV2000
cx88[1]:    card=9 -> Leadtek PVR 2000
cx88[1]:    card=10 -> IODATA GV-VCP3/PCI
cx88[1]:    card=11 -> Prolink PlayTV PVR
cx88[1]:    card=12 -> ASUS PVR-416
cx88[1]:    card=13 -> MSI TV- at nywhere
cx88[1]:    card=14 -> KWorld/VStream XPert DVB-T
cx88[1]:    card=15 -> DViCO FusionHDTV DVB-T1
cx88[1]:    card=16 -> KWorld LTV883RF
cx88[1]:    card=17 -> DViCO FusionHDTV 3 Gold-Q
cx88[1]:    card=18 -> Hauppauge Nova-T DVB-T
cx88[1]:    card=19 -> Conexant DVB-T reference design
cx88[1]:    card=20 -> Provideo PV259
cx88[1]:    card=21 -> DViCO FusionHDTV DVB-T Plus
cx88[1]:    card=22 -> pcHDTV HD3000 HDTV
cx88[1]:    card=23 -> digitalnow DNTV Live! DVB-T
cx88[1]:    card=24 -> Hauppauge WinTV 28xxx (Roslyn) models
cx88[1]:    card=25 -> Digital-Logic MICROSPACE Entertainment Center (MEC)
cx88[1]:    card=26 -> IODATA GV/BCTV7E
cx88[1]:    card=27 -> PixelView PlayTV Ultra Pro (Stereo)
cx88[1]:    card=28 -> DViCO FusionHDTV 3 Gold-T
cx88[1]:    card=29 -> ADS Tech Instant TV DVB-T PCI
cx88[1]:    card=30 -> TerraTec Cinergy 1400 DVB-T
cx88[1]:    card=31 -> DViCO FusionHDTV 5 Gold
cx88[1]:    card=32 -> AverMedia UltraTV Media Center PCI 550
cx88[1]:    card=33 -> Kworld V-Stream Xpert DVD
cx88[1]:    card=34 -> ATI HDTV Wonder
cx88[1]:    card=35 -> WinFast DTV1000-T
cx88[1]:    card=36 -> AVerTV 303 (M126)
cx88[1]:    card=37 -> Hauppauge Nova-S-Plus DVB-S
cx88[1]:    card=38 -> Hauppauge Nova-SE2 DVB-S
cx88[1]:    card=39 -> KWorld DVB-S 100
cx88[1]:    card=40 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid
cx88[1]:    card=41 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profile)
cx88[1]:    card=42 -> digitalnow DNTV Live! DVB-T Pro
cx88[1]:    card=43 -> KWorld/VStream XPert DVB-T with cx22702
cx88[1]:    card=44 -> DViCO FusionHDTV DVB-T Dual Digital
cx88[1]:    card=45 -> KWorld HardwareMpegTV XPert
cx88[1]:    card=46 -> DViCO FusionHDTV DVB-T Hybrid
cx88[1]:    card=47 -> pcHDTV HD5500 HDTV
cx88[1]:    card=48 -> Kworld MCE 200 Deluxe
cx88[1]:    card=49 -> PixelView PlayTV P7000
cx88[1]:    card=50 -> NPG Tech Real TV FM Top 10
cx88[1]:    card=51 -> WinFast DTV2000 H
cx88[1]:    card=52 -> Geniatech DVB-S
cx88[1]:    card=53 -> Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
cx88[1]:    card=54 -> Norwood Micro TV Tuner
cx88[1]:    card=55 -> Shenzhen Tungsten Ages Tech TE-DTV-250 / Swann OEM
cx88[1]:    card=56 -> Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder
CORE cx88[1]: subsystem: 0070:6902, board: UNKNOWN/GENERIC [card=0,autodetected]
TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[1]/2: cx2388x 8802 Driver Manager
CORE cx88[1]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[1]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:00:08.2[A] -> GSI 19 (level, low) -> IRQ 19
cx88[1]/2: found at 0000:00:08.2, rev: 3, irq: 19, latency: 32, mmio: 0xc8000000
ACPI: PCI Interrupt 0000:00:06.1[A] -> GSI 17 (level, low) -> IRQ 17
cx88[2]: Your board isn't known (yet) to the driver.  You can
cx88[2]: try to pick one of the existing card configs via
cx88[2]: card=<n> insmod option.  Updating to the latest
cx88[2]: version might help as well.
cx88[2]: Here is a list of valid choices for the card=<n> insmod option:
cx88[2]:    card=0 -> UNKNOWN/GENERIC
cx88[2]:    card=1 -> Hauppauge WinTV 34xxx models
cx88[2]:    card=2 -> GDI Black Gold
cx88[2]:    card=3 -> PixelView
cx88[2]:    card=4 -> ATI TV Wonder Pro
cx88[2]:    card=5 -> Leadtek Winfast 2000XP Expert
cx88[2]:    card=6 -> AverTV Studio 303 (M126)
cx88[2]:    card=7 -> MSI TV- at nywhere Master
cx88[2]:    card=8 -> Leadtek Winfast DV2000
cx88[2]:    card=9 -> Leadtek PVR 2000
cx88[2]:    card=10 -> IODATA GV-VCP3/PCI
cx88[2]:    card=11 -> Prolink PlayTV PVR
cx88[2]:    card=12 -> ASUS PVR-416
cx88[2]:    card=13 -> MSI TV- at nywhere
cx88[2]:    card=14 -> KWorld/VStream XPert DVB-T
cx88[2]:    card=15 -> DViCO FusionHDTV DVB-T1
cx88[2]:    card=16 -> KWorld LTV883RF
cx88[2]:    card=17 -> DViCO FusionHDTV 3 Gold-Q
cx88[2]:    card=18 -> Hauppauge Nova-T DVB-T
cx88[2]:    card=19 -> Conexant DVB-T reference design
cx88[2]:    card=20 -> Provideo PV259
cx88[2]:    card=21 -> DViCO FusionHDTV DVB-T Plus
cx88[2]:    card=22 -> pcHDTV HD3000 HDTV
cx88[2]:    card=23 -> digitalnow DNTV Live! DVB-T
cx88[2]:    card=24 -> Hauppauge WinTV 28xxx (Roslyn) models
cx88[2]:    card=25 -> Digital-Logic MICROSPACE Entertainment Center (MEC)
cx88[2]:    card=26 -> IODATA GV/BCTV7E
cx88[2]:    card=27 -> PixelView PlayTV Ultra Pro (Stereo)
cx88[2]:    card=28 -> DViCO FusionHDTV 3 Gold-T
cx88[2]:    card=29 -> ADS Tech Instant TV DVB-T PCI
cx88[2]:    card=30 -> TerraTec Cinergy 1400 DVB-T
cx88[2]:    card=31 -> DViCO FusionHDTV 5 Gold
cx88[2]:    card=32 -> AverMedia UltraTV Media Center PCI 550
cx88[2]:    card=33 -> Kworld V-Stream Xpert DVD
cx88[2]:    card=34 -> ATI HDTV Wonder
cx88[2]:    card=35 -> WinFast DTV1000-T
cx88[2]:    card=36 -> AVerTV 303 (M126)
cx88[2]:    card=37 -> Hauppauge Nova-S-Plus DVB-S
cx88[2]:    card=38 -> Hauppauge Nova-SE2 DVB-S
cx88[2]:    card=39 -> KWorld DVB-S 100
cx88[2]:    card=40 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid
cx88[2]:    card=41 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profile)
cx88[2]:    card=42 -> digitalnow DNTV Live! DVB-T Pro
cx88[2]:    card=43 -> KWorld/VStream XPert DVB-T with cx22702
cx88[2]:    card=44 -> DViCO FusionHDTV DVB-T Dual Digital
cx88[2]:    card=45 -> KWorld HardwareMpegTV XPert
cx88[2]:    card=46 -> DViCO FusionHDTV DVB-T Hybrid
cx88[2]:    card=47 -> pcHDTV HD5500 HDTV
cx88[2]:    card=48 -> Kworld MCE 200 Deluxe
cx88[2]:    card=49 -> PixelView PlayTV P7000
cx88[2]:    card=50 -> NPG Tech Real TV FM Top 10
cx88[2]:    card=51 -> WinFast DTV2000 H
cx88[2]:    card=52 -> Geniatech DVB-S
cx88[2]:    card=53 -> Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
cx88[2]:    card=54 -> Norwood Micro TV Tuner
cx88[2]:    card=55 -> Shenzhen Tungsten Ages Tech TE-DTV-250 / Swann OEM
cx88[2]:    card=56 -> Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder
CORE cx88[2]: subsystem: 0070:6902, board: UNKNOWN/GENERIC [card=0,autodetected]
TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[2]/1: CX88x/0: ALSA support for cx2388x boards
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 16
cx88[0]/0: found at 0000:00:05.0, rev: 3, irq: 16, latency: 32, mmio: 0xcd000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 17
cx88[2]/0: found at 0000:00:06.0, rev: 5, irq: 17, latency: 32, mmio: 0xc9000000
cx88[2]/0: registered device video1 [v4l2]
cx88[2]/0: registered device vbi1
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19
cx88[1]/0: found at 0000:00:08.0, rev: 3, irq: 19, latency: 32, mmio: 0xc7000000
cx88[1]/0: registered device video2 [v4l2]
cx88[1]/0: registered device vbi2
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  1.0-9746  Fri Dec 15 10:19:35 PST 2006
XFS mounting filesystem sda2
Ending clean XFS mount for filesystem: sda2
XFS mounting filesystem sdc4
Ending clean XFS mount for filesystem: sdc4
Adding 1004020k swap on /dev/sdb1.  Priority:2 extents:1 across:1004020k
Adding 506036k swap on /dev/sdc2.  Priority:2 extents:1 across:506036k
usb-storage: device scan complete
scsi 5:0:0:0: Direct-Access     SMSC     223 U HS-CF      3.60 PQ: 0 ANSI: 0
scsi 5:0:0:1: Direct-Access     SMSC     223 U HS-MS      3.60 PQ: 0 ANSI: 0
scsi 5:0:0:2: Direct-Access     SMSC     223 U HS-SM      3.60 PQ: 0 ANSI: 0
scsi 5:0:0:3: Direct-Access     SMSC     223 U HS-SD/MMC  3.60 PQ: 0 ANSI: 0
sd 5:0:0:0: Attached scsi removable disk sdd
sd 5:0:0:0: Attached scsi generic sg5 type 0
sd 5:0:0:1: Attached scsi removable disk sde
sd 5:0:0:1: Attached scsi generic sg6 type 0
sd 5:0:0:2: Attached scsi removable disk sdf
sd 5:0:0:2: Attached scsi generic sg7 type 0
sd 5:0:0:3: Attached scsi removable disk sdg
sd 5:0:0:3: Attached scsi generic sg8 type 0
cx2388x dvb driver version 0.0.6 loaded
cx8802_register_driver() ->registering driver type=dvb access=shared
CORE cx88[0]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52]
cx88[0]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 1 (Conexant CX24123/CX24109)...
CORE cx88[1]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52]
cx88[1]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[1]).
DVB: registering frontend 2 (Conexant CX24123/CX24109)...
r8169: eth0: link up
cdrom: This disc doesn't have any tracks I recognize!
cx8802_unregister_driver() ->unregistering driver type=dvb
CORE cx88[0]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52]
CORE cx88[1]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52]
saa7146: unregister extension 'budget_ci dvb'.
saa7146: register extension 'budget_ci dvb'.
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 18
saa7146: found saa7146 @ mem ffffc2000007ce00 (revision 1, irq 18) (0x13c2,0x100f).
saa7146 (0): dma buffer size 192512
DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI).
adapter has MAC addr = 00:d0:5c:23:a3:9b
input: Budget-CI dvb ir receiver saa7146 (0) as /class/input/input7
DVB: registering frontend 0 (ST STV0299 DVB-S)...
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
CORE cx88[1]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[1]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:00:05.2[A] -> GSI 16 (level, low) -> IRQ 16
cx88[1]/2: found at 0000:00:05.2, rev: 3, irq: 16, latency: 32, mmio: 0xce000000
cx88[2]/2: cx2388x 8802 Driver Manager
CORE cx88[2]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[2]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:00:08.2[A] -> GSI 19 (level, low) -> IRQ 19
cx88[2]/2: found at 0000:00:08.2, rev: 3, irq: 19, latency: 32, mmio: 0xc8000000
cx2388x dvb driver version 0.0.6 loaded
cx8802_register_driver() ->registering driver type=dvb access=shared
CORE cx88[1]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52]
cx88[1]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[1]).
DVB: registering frontend 1 (Conexant CX24123/CX24109)...
CORE cx88[2]: subsystem: 14f1:0084, board: Geniatech DVB-S [card=52]
cx88[2]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[2]).
DVB: registering frontend 2 (Conexant CX24123/CX24109)...
cx88[2]/2-mpeg: cx8802_timeout
-------------- next part --------------
00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
	Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 8
	Region 0: Memory at <ignored> (32-bit, prefetchable)
	Capabilities: [80] AGP version 3.0
		Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
	Capabilities: [c0] HyperTransport: Slave or Primary Interface
		!!! Possibly incomplete decoding
		Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir-
		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
		Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
		Revision ID: 1.02
	Capabilities: [68] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration

00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: bde00000-bfefffff
	Prefetchable memory behind bridge: 9dd00000-bdcfffff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:05.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 03)
	Subsystem: Conexant Unknown device 0084
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at cd000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:05.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 03)
	Subsystem: Conexant Unknown device 0084
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
	Subsystem: Hauppauge computer works Inc. Unknown device 6902
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at c9000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
	Subsystem: Hauppauge computer works Inc. Unknown device 6902
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1000ns min, 63750ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at ca000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
	Subsystem: Hauppauge computer works Inc. Unknown device 6902
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at cb000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
	Subsystem: Hauppauge computer works Inc. Unknown device 6902
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1500ns min, 63750ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at cc000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
	Subsystem: Technotrend Systemtechnik GmbH Technotrend-Budget/Hauppauge WinTV-NOVA-CI DVB card
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (3750ns min, 9500ns max)
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at cfffee00 (32-bit, non-prefetchable) [size=512]

00:08.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 03)
	Subsystem: Conexant Unknown device 0084
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at c7000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:08.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 03)
	Subsystem: Conexant Unknown device 0084
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at c8000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
	Subsystem: Adaptec 29160 Ultra160 SCSI Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 17
	BIST result: 00
	Region 0: I/O ports at ec00 [disabled] [size=256]
	Region 1: Memory at cffff000 (64-bit, non-prefetchable) [size=4K]
	Expansion ROM at cffc0000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at e800 [size=256]
	Region 1: Memory at cfffed00 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at cffa0000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
	Subsystem: Micro-Star International Co., Ltd. K8T Neo 2 Motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin B routed to IRQ 20
	Region 0: I/O ports at e400 [size=8]
	Region 1: I/O ports at e000 [size=4]
	Region 2: I/O ports at dc00 [size=8]
	Region 3: I/O ports at d800 [size=4]
	Region 4: I/O ports at d400 [size=16]
	Region 5: I/O ports at d000 [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Interrupt: pin A routed to IRQ 20
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
	Region 4: I/O ports at fc00 [size=16]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 21
	Region 4: I/O ports at c000 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 21
	Region 4: I/O ports at c400 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 21
	Region 4: I/O ports at c800 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 21
	Region 4: I/O ports at cc00 [size=32]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 21
	Region 0: Memory at cfffeb00 (32-bit, non-prefetchable) [size=256]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
	Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
	Subsystem: Micro-Star International Co., Ltd. K8T NEO 2 motherboard
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin C routed to IRQ 22
	Region 0: I/O ports at bc00 [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		!!! Possibly incomplete decoding
		Command: WarmRst+ DblEnd-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Revision ID: 1.02

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

01:00.0 VGA compatible controller: nVidia Corporation NV38 [GeForce FX 5950 Ultra] (rev a1) (prog-if 00 [VGA])
	Subsystem: Micro-Star International Co., Ltd. Unknown device 9460
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1250ns min, 250ns max)
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at be000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at a0000000 (32-bit, prefetchable) [size=256M]
	Expansion ROM at bfee0000 [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [44] AGP version 3.0
		Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>



More information about the linux-dvb mailing list