[linux-dvb] [PATCH] Add initial support for DViCO FusionHDTV DVB-T Dual Express
Tim Farrington
timf at iinet.net.au
Thu Aug 7 09:00:04 CEST 2008
David wrote:
> ----- Original Message -----
> From: "Tim Farrington" <timf at iinet.net.au>
> To: "David" <dvb-t at iinet.com.au>
> Cc: <linux-dvb at linuxtv.org>
> Sent: Thursday, August 07, 2008 2:34 PM
> Subject: Re: [linux-dvb] [PATCH] Add initial support for DViCO FusionHDTV
> DVB-T Dual Express
>
>
>
>> David wrote:
>>
>>> Hi Tim
>>>
>>> Thanks for information.
>>>
>>> I obtained the driver, extracted the firmware to lib/firmware and tried
>>> to scan.
>>> I cannot get a lock on anything.
>>>
>>> dmesg shows it is loading the firmware but nothing more:
>>>
>>> [ 192.596627] xc2028 1-0061: Loading 3 firmware images from
>>> xc3028-v27.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7
>>> [ 192.796658] xc2028 1-0061: Loading firmware for type=BASE F8MHZ (3),
>>> id 0000000000000000.
>>> [ 193.965865] xc2028 1-0061: Loading firmware for type=D2620 DTV7 (88),
>>> id 0000000000000000.
>>> [ 265.268818] xc2028 2-0061: Loading 3 firmware images from
>>> xc3028-v27.fw, type: DViCO DualDig4/Nano2 (Australia), ver 2.7
>>> [ 265.468693] xc2028 2-0061: Loading firmware for type=BASE F8MHZ (3),
>>> id 0000000000000000.
>>> [ 266.633170] xc2028 2-0061: Loading firmware for type=D2620 DTV7 (88),
>>> id 0000000000000000.
>>>
>>>
>>> Regards
>>> David
>>>
>>>
>>>
>>> ----- Original Message ----- From: "Tim Farrington" <timf at iinet.net.au>
>>> To: "David Porter" <dvb-t at iinet.com.au>
>>> Cc: <linux-dvb at linuxtv.org>
>>> Sent: Wednesday, August 06, 2008 6:51 PM
>>> Subject: Re: [linux-dvb] [PATCH] Add initial support for DViCO FusionHDTV
>>> DVB-T Dual Express
>>>
>>>
>>>
>>>> David Porter wrote:
>>>>
>>>>> Hi
>>>>>
>>>>> I have one of these, saw Stevens post and thought i would give it a go.
>>>>>
>>>>> I built from : http://linuxtv.org/hg/~stoth/v4l-dvb
>>>>> All seemed to go well with no errors.
>>>>>
>>>>> dmesg reads:
>>>>>
>>>>> [ 31.964424] CORE cx23885[0]: subsystem: 18ac:db78, board: DViCO
>>>>> FusionHDTV DVB-T Dual Express [card=11,autodetected]
>>>>> [ 32.104767] cx23885[0]: i2c bus 0 registered
>>>>> [ 32.104781] cx23885[0]: i2c bus 1 registered
>>>>> [ 32.104794] cx23885[0]: i2c bus 2 registered
>>>>> [ 32.164385] input: i2c IR (FusionHDTV) as
>>>>> /devices/virtual/input/input8
>>>>> [ 32.422764] ir-kbd-i2c: i2c IR (FusionHDTV) detected at
>>>>> i2c-1/1-006b/ir0 [cx23885[0]]
>>>>> [ 32.423135] cx23885[0]: cx23885 based dvb card
>>>>> [ 32.492021] xc2028 1-0061: creating new instance
>>>>> [ 32.492027] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
>>>>> [ 32.492036] DVB: registering new adapter (cx23885[0])
>>>>> [ 32.492040] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
>>>>> [ 32.492386] cx23885[0]: cx23885 based dvb card
>>>>> [ 32.492924] xc2028 2-0061: creating new instance
>>>>> [ 32.492926] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
>>>>> [ 32.492928] DVB: registering new adapter (cx23885[0])
>>>>> [ 32.492930] DVB: registering frontend 1 (Zarlink ZL10353 DVB-T)...
>>>>> [ 32.493228] cx23885_dev_checkrevision() Hardware revision = 0xb0
>>>>> [ 32.493236] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16,
>>>>> latency: 0, mmio: 0xfe800000
>>>>>
>>>>> But scanning, returns :
>>>>>
>>>>> [ 1381.214624] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
>>>>> [ 1382.220858] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
>>>>> [ 1382.260825] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
>>>>> [ 1383.267724] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
>>>>> [ 1383.276680] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
>>>>>
>>>>> I checked /lib/firmware/ but xc3028-v27.fw is not in the directory ?
>>>>>
>>>>> Must have messed it up somewhere! Any help appreciated.
>>>>>
>>>>> Thanks
>>>>> David
>>>>>
>>>>> ----- Original Message ----- From: "Steven Toth" <stoth at linuxtv.org>
>>>>> To: "Luke Yelavich" <themuso at themuso.com>
>>>>> Cc: <linux-dvb at linuxtv.org>
>>>>> Sent: Wednesday, August 06, 2008 11:44 AM
>>>>> Subject: Re: [linux-dvb] [PATCH] Add initial support for DViCO
>>>>> FusionHDTV DVB-T Dual Express
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>>>>> I've tested with the HVR1500Q (xc5000 based) and I'm happy with the
>>>>>>>>> results. Can you both try the DViCO board?
>>>>>>>>>
>>>>>>>>>
>>>>>>>> It tests fine and I like how simpler things have got.
>>>>>>>>
>>>>>>>>
>>>>>>> I pulled the above linked tree, and compiled the modules. It seems at
>>>>>>> the moment for the dual express, that I have to pass the parameter
>>>>>>> card=11 to the driver, for it to correctly find the card and make use
>>>>>>> of all adapters. Without any module parameters, dmsg complains that
>>>>>>> the card couldn't be identified, yet two adapters are shown. I have
>>>>>>> two of these cards.
>>>>>>>
>>>>>>> Hope this helps some.
>>>>>>>
>>>>>>>
>>>>>> .. And they're both the same model?
>>>>>>
>>>>>> If so, insert one at a time and run the 'lspci -vn' command, save the
>>>>>> output for each card.
>>>>>>
>>>>>> Post the output here.
>>>>>>
>>>>>> Assuming you load the driver with card=11, does each card work
>>>>>> correctly
>>>>>> after that?
>>>>>>
>>>>>> - Steve
>>>>>>
>>>>>> _______________________________________________
>>>>>> linux-dvb mailing list
>>>>>> linux-dvb at linuxtv.org
>>>>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>>>>>>
>>>>>>
>>>>>>
>>>>> _______________________________________________
>>>>> linux-dvb mailing list
>>>>> linux-dvb at linuxtv.org
>>>>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>>>>>
>>>>>
>>>>>
>>>> To obtain xc3028-v27.fw
>>>>
>>>> see ~/v4l-dvb/linux/Documentation/video4linux/extract_xc3028.pl
>>>>
>>>> Regards,
>>>> Timf
>>>>
>> Try not to top post.
>>
>> Best to post the results of tzap here:
>>
>> In Ubuntu, Debian;
>> sudo apt-get install dvb-utils
>> (other distros use dvb-apps)
>>
>> Find the scan file appropriate for your area (au-*) in:
>> /usr/share/doc/dvb-utils/examples/scan/dvb-t
>>
>> sudo -s -H
>> mkdir /root/.tzap
>> scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-* >
>> /root/.tzap/channels.conf
>>
>> Post the output of scan to this list.
>>
>> Regards,
>> Timf
>>
>
> Thanks, Tim
> Doesn't look too promising :
>
> a at a-desktop:~$ scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Brisbane
> scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Brisbane
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> initial transponder 226500000 1 3 9 3 1 1 0
> initial transponder 177500000 1 2 9 3 1 2 0
> initial transponder 191625000 1 3 9 3 1 1 0
> initial transponder 219500000 1 3 9 3 1 1 0
> initial transponder 585625000 1 2 9 3 1 2 0
>
>>>> tune to:
>>>> 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE
>>>> (tuning failed)
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
>>>> (tuning failed)
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE
>>>> (tuning failed)
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE
>>>> (tuning failed)
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 585625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
>>>>
> WARNING: >>> tuning failed!!!
>
>>>> tune to:
>>>> 585625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
>>>> (tuning failed)
>>>>
> WARNING: >>> tuning failed!!!
> ERROR: initial tuning failed
> dumping lists (0 services)
> Done.
> a at a-desktop:~$
>
> Regards
> David
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
Could be that the signal strength is too low.
What are you using for an antenna?
How does it go in Windows - any channels?
Regards,
Timf
More information about the linux-dvb
mailing list