No subject


Mon Jul 28 21:58:57 CEST 2008


I hope this helps you get started. 

Regards, 
Mark 






diff -Naur 
v4l-dvb-2bade2ed7ac8/linux/Documentation/video4linux/CARDLIST.cx23885 
v4l-dvb2/linux/Documentation/video4linux/CARDLIST.cx23885 
--- 
v4l-dvb-2bade2ed7ac8/linux/Documentation/video4linux/CARDLIST.cx23885 2008-08-05 11:18:19.000000000 
+1000 
+++ 
v4l-dvb2/linux/Documentation/video4linux/CARDLIST.cx23885 2008-08-05 
23:27:32.000000000 +1000 
@@ -10,3 +10,4 @@ 
9 -> Hauppauge WinTV-HVR1400 [0070:8010] 
10 -> DViCO FusionHDTV7 Dual Express [18ac:d618] 
11 -> DViCO FusionHDTV DVB-T Dual Express [18ac:db78] 
+ 12 -> Leadtek Winfast PxDVR3200 H [107d:6681] 
diff -Naur 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/Kconfig 
v4l-dvb2/linux/drivers/media/video/cx23885/Kconfig 
--- 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/Kconfig 2008-08-05 
11:18:19.000000000 +1000 
+++ v4l-dvb2/linux/drivers/media/video/cx23885/Kconfig 2008-08-05 
23:37:51.000000000 +1000 
@@ -15,6 +15,7 @@ 
select DVB_S5H1409 if !DVB_FE_CUSTOMISE 
select DVB_S5H1411 if !DVB_FE_CUSTOMISE 
select DVB_LGDT330X if !DVB_FE_CUSTOMISE 
+ select DVB_ZL10353 if !DVB_FE_CUSTOMISE 
select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMIZE 
select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE 
select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE 
diff -Naur 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-cards.c 
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-cards.c 
--- 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-cards.c 2008-08-05 11:18:19.000000000 
+1000 
+++ 
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-cards.c 2008-08-05 
23:41:40.000000000 +1000 
@@ -155,6 +155,10 @@ 
.portb = CX23885_MPEG_DVB, 
.portc = CX23885_MPEG_DVB, 
}, 
+ [CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H] = { 
+ .name = "Leadtek Winfast PxDVR3200 H", 
+ .portc = CX23885_MPEG_DVB, 
+ }, 
}; 
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards); 

@@ -230,6 +234,10 @@ 
.subvendor = 0x18ac, 
.subdevice = 0xdb78, 
.card = CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP, 
+ },{ 
+ .subvendor = 0x107d, 
+ .subdevice = 0x6681, 
+ .card = CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H, 
}, 
}; 
const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids); 
@@ -353,6 +361,10 @@ 
if (command == 0) 
bitmask = 0x04; 
break; 
+ case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H: 
+ /* Tuner Reset Command */ 
+ bitmask = 0x00070404; 
+ break; 
case CX23885_BOARD_DVICO_FUSIONHDTV_7_DUAL_EXP: 
case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP: 
if (command == 0) { 
@@ -492,6 +504,15 @@ 
mdelay(20); 
cx_set(GP0_IO, 0x000f000f); 
break; 
+ case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H: 
+ /* GPIO-2 xc3028 tuner reset */ 
+ /* Put the parts into reset and back */ 
+ cx_set(GP0_IO, 0x00040000); 
+ mdelay(20); 
+ cx_clear(GP0_IO, 0x00000004); 
+ mdelay(20); 
+ cx_set(GP0_IO, 0x00040004); 
+ break; 
} 
} 

@@ -579,6 +600,7 @@ 
case CX23885_BOARD_HAUPPAUGE_HVR1200: 
case CX23885_BOARD_HAUPPAUGE_HVR1700: 
case CX23885_BOARD_HAUPPAUGE_HVR1400: 
+ case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H: 
default: 
ts2->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */ 
ts2->ts_clk_en_val = 0x1; /* Enable TS_CLK */ 
@@ -592,6 +614,7 @@ 
case CX23885_BOARD_HAUPPAUGE_HVR1800: 
case CX23885_BOARD_HAUPPAUGE_HVR1800lp: 
case CX23885_BOARD_HAUPPAUGE_HVR1700: 
+ case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H: 
request_module("cx25840"); 
break; 
} 
diff -Naur 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-dvb.c 
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-dvb.c 
--- 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-dvb.c 2008-08-05 11:18:19.000000000 
+1000 
+++ 
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-dvb.c 2008-08-05 
23:37:03.000000000 +1000 
@@ -37,6 +37,7 @@ 
#include "tda8290.h" 
#include "tda18271.h" 
#include "lgdt330x.h" 
+#include "zl10353.h" 
#include "xc5000.h" 
#include "tda10048.h" 
#include "tuner-xc2028.h" 
@@ -502,6 +503,32 @@ 
} 
break; 
} 
+ case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H: 
+ i2c_bus = &dev->i2c_bus[0]; 
+ 
+ port->dvb.frontend = dvb_attach(zl10353_attach, 
+ &dvico_fusionhdtv_xc3028, 
+ &i2c_bus->i2c_adap); 
+ if (port->dvb.frontend != NULL) { 
+ struct dvb_frontend *fe; 
+ struct xc2028_config cfg = { 
+ .i2c_adap = &dev->i2c_bus[1].i2c_adap, 
+ .i2c_addr = 0x61, 
+ .video_dev = port, 
+ .callback = cx23885_tuner_callback, 
+ }; 
+ static struct xc2028_ctrl ctl = { 
+ .fname = "xc3028-v27.fw", 
+ .max_len = 64, 
+ .demod = XC3028_FE_ZARLINK456, 
+ }; 
+ 
+ fe = dvb_attach(xc2028_attach, port->dvb.frontend, 
+ &cfg); 
+ if (fe != NULL && fe->ops.tuner_ops.set_config != NULL) 
+ fe->ops.tuner_ops.set_config(fe, &ctl); 
+ } 
+ break; 
default: 
printk("%s: The frontend of your DVB/ATSC card isn't supported yet\n", 
dev->name); 
diff -Naur 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885.h 
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885.h 
--- 
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885.h 2008-08-05 
11:18:19.000000000 +1000 
+++ v4l-dvb2/linux/drivers/media/video/cx23885/cx23885.h 2008-08-05 
23:37:33.000000000 +1000 
@@ -66,6 +66,7 @@ 
#define CX23885_BOARD_HAUPPAUGE_HVR1400 9 
#define CX23885_BOARD_DVICO_FUSIONHDTV_7_DUAL_EXP 10 
#define CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP 11 
+#define CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H 12 

/* Currently unsupported by the driver: PAL/H, NTSC/Kr, SECAM B/G/H/LC */ 
#define CX23885_NORMS (\ 
<< Leadtek.Winfast.PxDVR.3200.H.2.diff >> 

-- 
Be Yourself @ mail.com! 
Choose From 200+ Email Addresses 
Get a Free Account at www.mail.com ! 
------=_Part_0_8087063.1218023586329
Content-Type: text/html; charset=utf-8
Content-Transfer-Encoding: quoted-printable

<html><head><style type=3D'text/css'>p { margin: 0; }</style></head><body><=
div style=3D'font-family: Times New Roman; font-size: 12pt; color: #000000'=
>Hi Stephen,<br><br>So far so good, once I loaded the firmware for the tune=
r it all started working.&nbsp; dvbscan was able to pick up the pids on the=
 various channels and mythtv was also able to tune the channels although I =
had to enter the transports manually as I would end up with some transport =
frequencies being 0 (ABC, SBS &amp; channel 9 seem to not scan automaticall=
y), but then I have that problem with my Dvico hd plus also.<br><br>The sig=
nal strenth is a little low which is causing frequent breakups, but that co=
uld just be the antenna outlet I am using (at the end of a long cable run) =
or the hardware itself, but it is sufficent for testing.<br><br>I have been=
 messing around for a few hours now, tuning, watching tv for a bit changes =
channels all over the place and so far I haven't seen any issues.&nbsp; I h=
ave not been able to replicate the card not being autodetected issue that y=
ou mention, just works for me everytime.<br><br>If I find any issues I will=
 certainly post them, please let me know if you need me to do anything spec=
ific and thanks for your effort in getting this working.<br><br>Mark<br><br=
>----- Original Message -----<br>From: stev391 at email.com<br>To: "Mark Carbo=
naro" &lt;mark at carbonaro.org&gt;, "Jonathan Hummel" &lt;jhhummel at bigpond.co=
m&gt;<br>Cc: stev391 at email.com, linux-dvb at linuxtv.org<br>Sent: Wednesday, 6=
 August, 2008 7:33:49 AM (GMT+1000) Auto-Detected<br>Subject: Re: [PATCH-TE=
STERS-REQUIRED] Leadtek Winfast PxDVR 3200 H - DVB Only support<br><br>
<div>
Mark, Jon,<br><br>The patches I made were not against the v4l-dvb tip that =
is referenced in Mark's email below.&nbsp; I did this on purpose because th=
ere is a small amount of refactoring (recoding to make it better) being per=
formed by Steven Toth and others.<br><br>To get the version I used for the =
patch download (This is for the first initial patch [you can tell it is thi=
s one as the patch file mentions cx23885-sram in the path]):<br>http://linu=
xtv.org/hg/~stoth/cx23885-sram/archive/tip.tar.gz<br><br>For the second pat=
ch that emailed less then 12 hours ago download this version of drivers:<br=
>http://linuxtv.org/hg/~stoth/v4l-dvb/archive/tip.tar.gz<br>and then apply =
my patch (this patch mentions v4l-dvb). This version is a cleanup of the pr=
evious and uses the generic callback function.<br><br>Other then that you a=
re heading in the correct direction...<br><br>Do either of you have the sam=
e issue I have that when the computer is first turned on the autodetect car=
d feature doesn't work due to subvendor sub product ids of 0000? Or is just=
 a faulty card that I have?<br>
<br>Regards,<br><br>Stephen.<br>
<blockquote style=3D"border-left: 2px solid rgb(16, 16, 255); margin-left: =
5px; padding-left: 5px;">----- Original Message -----<br>
From: "Mark Carbonaro" <br>
To: "Jonathan Hummel" <br>
Subject: Re: [PATCH-TESTERS-REQUIRED] Leadtek Winfast PxDVR 3200 H - DVB On=
ly support<br>
Date: Tue, 5 Aug 2008 23:47:46 +1000 (EST)<br>
<br>

<br>
Hi Mark,<br>
<br>
Forgive my ignorance/ newbie-ness, but what do I do with that patch code<br=
>
below? is there a tutorial or howto or something somewhere that will<br>
introduce me to this. I have done some programming, but nothing of this<br>
level.<br>
<br>
cheers<br>
<br>
Jon<br>
<br>
----- Original Message -----<br>
From: "Jonathan Hummel" <br>
To: "Mark Carbonaro" <br>
Cc: stev391 at email.com, linux-dvb at linuxtv.org<br>
Sent: Tuesday, 5 August, 2008 10:21:11 PM (GMT+1000) Auto-Detected<br>
Subject: Re: [PATCH-TESTERS-REQUIRED] Leadtek Winfast PxDVR 3200 H <br>
- DVB Only support<br>
<br>
Hi Jon,<br>
<br>
Not a problem at all, I'm new to this myself, below is what went <br>
through and I may not be doing it the right way either.  So if <br>
anyone would like to point out what I am doing wrong I would really <br>
appreciate it.<br>
<br>
The file that I downloaded was called v4l-dvb-2bade2ed7ac8.tar.bz2 <br>
which I downloaded from <br>
http://linuxtv.org/hg/~stoth/v4l-dvb/archive/tip.tar.bz2, I also <br>
saved the patch to the same location as the download.<br>
<br>
The patch didn't apply for me, so I manually patched applied the <br>
patches and created a new diff that should hopefully work for you <br>
also (attached and inline below).  From what I could see the <br>
offsets in Stephens patch were a little off for this code snapshot <br>
but otherwise it is all good.<br>
<br>
I ran the following using the attached diff...<br>
<br>
tar -xjf v4l-dvb-2bade2ed7ac8.tar.bz2<br>
cd v4l-dvb-2bade2ed7ac8<br>
patch -p1 &lt; ../Leadtek.Winfast.PxDVR.3200.H.2.diff<br>
<br>
Once the patch was applied I was then able to build and install the <br>
modules as per the instructions in the INSTALL file.  I ran the <br>
following...<br>
<br>
make all<br>
sudo make install<br>
<br>
 From there I could load the modules and start testing.<br>
<br>
I hope this helps you get started.<br>
<br>
Regards,<br>
Mark<br>
<br>
<br>
<br>
<br>
<br>
<br>
diff -Naur <br>
v4l-dvb-2bade2ed7ac8/linux/Documentation/video4linux/CARDLIST.cx23885 <br>
v4l-dvb2/linux/Documentation/video4linux/CARDLIST.cx23885<br>
--- <br>
v4l-dvb-2bade2ed7ac8/linux/Documentation/video4linux/CARDLIST.cx23885=09200=
8-08-05 11:18:19.000000000 <br>
+1000<br>
+++ <br>
v4l-dvb2/linux/Documentation/video4linux/CARDLIST.cx23885=092008-08-05 <br>
23:27:32.000000000 +1000<br>
@@ -10,3 +10,4 @@<br>
    9 -&gt; Hauppauge WinTV-HVR1400                             [0070:8010]=
<br>
   10 -&gt; DViCO FusionHDTV7 Dual Express                      [18ac:d618]=
<br>
   11 -&gt; DViCO FusionHDTV DVB-T Dual Express                 [18ac:db78]=
<br>
+ 12 -&gt; Leadtek Winfast PxDVR3200 H                         [107d:6681]<=
br>
diff -Naur <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/Kconfig <br>
v4l-dvb2/linux/drivers/media/video/cx23885/Kconfig<br>
--- <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/Kconfig=092008-08-05=
 <br>
11:18:19.000000000 +1000<br>
+++ v4l-dvb2/linux/drivers/media/video/cx23885/Kconfig=092008-08-05 <br>
23:37:51.000000000 +1000<br>
@@ -15,6 +15,7 @@<br>
  =09select DVB_S5H1409 if !DVB_FE_CUSTOMISE<br>
  =09select DVB_S5H1411 if !DVB_FE_CUSTOMISE<br>
  =09select DVB_LGDT330X if !DVB_FE_CUSTOMISE<br>
+=09select DVB_ZL10353 if !DVB_FE_CUSTOMISE<br>
  =09select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMIZE<br>
  =09select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE<br>
  =09select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE<br>
diff -Naur <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-cards.c <br>
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-cards.c<br>
--- <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-cards.c=0920=
08-08-05 11:18:19.000000000 <br>
+1000<br>
+++ <br>
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-cards.c=092008-08-05 <br=
>
23:41:40.000000000 +1000<br>
@@ -155,6 +155,10 @@<br>
  =09=09.portb=09=09=3D CX23885_MPEG_DVB,<br>
  =09=09.portc=09=09=3D CX23885_MPEG_DVB,<br>
  =09},<br>
+=09[CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H] =3D {<br>
+=09=09.name        =3D "Leadtek Winfast PxDVR3200 H",<br>
+=09=09.portc        =3D CX23885_MPEG_DVB,<br>
+=09},<br>
  };<br>
  const unsigned int cx23885_bcount =3D ARRAY_SIZE(cx23885_boards);<br>
<br>
@@ -230,6 +234,10 @@<br>
  =09=09.subvendor =3D 0x18ac,<br>
  =09=09.subdevice =3D 0xdb78,<br>
  =09=09.card      =3D CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP,<br>
+=09},{<br>
+=09=09.subvendor =3D 0x107d,<br>
+=09=09.subdevice =3D 0x6681,<br>
+=09=09.card      =3D CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H,<br>
  =09},<br>
  };<br>
  const unsigned int cx23885_idcount =3D ARRAY_SIZE(cx23885_subids);<br>
@@ -353,6 +361,10 @@<br>
  =09=09if (command =3D=3D 0)<br>
  =09=09=09bitmask =3D 0x04;<br>
  =09=09break;<br>
+=09case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:<br>
+=09=09/* Tuner Reset Command */<br>
+=09=09bitmask =3D 0x00070404;<br>
+=09=09break;<br>
  =09case CX23885_BOARD_DVICO_FUSIONHDTV_7_DUAL_EXP:<br>
  =09case CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP:<br>
  =09=09if (command =3D=3D 0) {<br>
@@ -492,6 +504,15 @@<br>
  =09=09mdelay(20);<br>
  =09=09cx_set(GP0_IO, 0x000f000f);<br>
  =09=09break;<br>
+=09case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:<br>
+=09=09/* GPIO-2  xc3028 tuner reset */<br>
+=09=09/* Put the parts into reset and back */<br>
+=09=09cx_set(GP0_IO, 0x00040000);<br>
+=09=09mdelay(20);<br>
+=09=09cx_clear(GP0_IO, 0x00000004);<br>
+=09=09mdelay(20);<br>
+=09=09cx_set(GP0_IO, 0x00040004);<br>
+=09=09break;<br>
  =09}<br>
  }<br>
<br>
@@ -579,6 +600,7 @@<br>
  =09case CX23885_BOARD_HAUPPAUGE_HVR1200:<br>
  =09case CX23885_BOARD_HAUPPAUGE_HVR1700:<br>
  =09case CX23885_BOARD_HAUPPAUGE_HVR1400:<br>
+=09case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:<br>
  =09default:<br>
  =09=09ts2-&gt;gen_ctrl_val  =3D 0xc; /* Serial bus + punctured clock */<b=
r>
  =09=09ts2-&gt;ts_clk_en_val =3D 0x1; /* Enable TS_CLK */<br>
@@ -592,6 +614,7 @@<br>
  =09case CX23885_BOARD_HAUPPAUGE_HVR1800:<br>
  =09case CX23885_BOARD_HAUPPAUGE_HVR1800lp:<br>
  =09case CX23885_BOARD_HAUPPAUGE_HVR1700:<br>
+=09case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:<br>
  =09=09request_module("cx25840");<br>
  =09=09break;<br>
  =09}<br>
diff -Naur <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-dvb.c <br>
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-dvb.c<br>
--- <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885-dvb.c=092008=
-08-05 11:18:19.000000000 <br>
+1000<br>
+++ <br>
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885-dvb.c=092008-08-05 <br>
23:37:03.000000000 +1000<br>
@@ -37,6 +37,7 @@<br>
  #include "tda8290.h"<br>
  #include "tda18271.h"<br>
  #include "lgdt330x.h"<br>
+#include "zl10353.h"<br>
  #include "xc5000.h"<br>
  #include "tda10048.h"<br>
  #include "tuner-xc2028.h"<br>
@@ -502,6 +503,32 @@<br>
  =09=09}<br>
  =09=09break;<br>
  =09}<br>
+=09case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:<br>
+=09=09i2c_bus =3D &amp;dev-&gt;i2c_bus[0];<br>
+<br>
+=09=09port-&gt;dvb.frontend =3D dvb_attach(zl10353_attach,<br>
+=09=09=09=09=09=09&amp;dvico_fusionhdtv_xc3028,<br>
+=09=09=09=09=09=09&amp;i2c_bus-&gt;i2c_adap);<br>
+=09=09if (port-&gt;dvb.frontend !=3D NULL) {<br>
+=09=09=09struct dvb_frontend      *fe;<br>
+=09=09=09struct xc2028_config      cfg =3D {<br>
+=09=09=09=09.i2c_adap  =3D &amp;dev-&gt;i2c_bus[1].i2c_adap,<br>
+=09=09=09=09.i2c_addr  =3D 0x61,<br>
+=09=09=09=09.video_dev =3D port,<br>
+=09=09=09=09.callback  =3D cx23885_tuner_callback,<br>
+=09=09=09};<br>
+=09=09=09static struct xc2028_ctrl ctl =3D {<br>
+=09=09=09=09.fname       =3D "xc3028-v27.fw",<br>
+=09=09=09=09.max_len     =3D 64,<br>
+=09=09=09=09.demod       =3D XC3028_FE_ZARLINK456,<br>
+=09=09=09};<br>
+<br>
+=09=09=09fe =3D dvb_attach(xc2028_attach, port-&gt;dvb.frontend,<br>
+=09=09=09=09=09&amp;cfg);<br>
+=09=09=09if (fe !=3D NULL &amp;&amp; fe-&gt;ops.tuner_ops.set_config !=3D =
NULL)<br>
+=09=09=09=09fe-&gt;ops.tuner_ops.set_config(fe, &amp;ctl);<br>
+=09=09}<br>
+=09=09break;<br>
  =09default:<br>
  =09=09printk("%s: The frontend of your DVB/ATSC card isn't supported yet\=
n",<br>
  =09=09       dev-&gt;name);<br>
diff -Naur <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885.h <br>
v4l-dvb2/linux/drivers/media/video/cx23885/cx23885.h<br>
--- <br>
v4l-dvb-2bade2ed7ac8/linux/drivers/media/video/cx23885/cx23885.h=092008-08-=
05 <br>
11:18:19.000000000 +1000<br>
+++ v4l-dvb2/linux/drivers/media/video/cx23885/cx23885.h=092008-08-05 <br>
23:37:33.000000000 +1000<br>
@@ -66,6 +66,7 @@<br>
  #define CX23885_BOARD_HAUPPAUGE_HVR1400        9<br>
  #define CX23885_BOARD_DVICO_FUSIONHDTV_7_DUAL_EXP 10<br>
  #define CX23885_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL_EXP 11<br>
+#define CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H 12<br>
<br>
  /* Currently unsupported by the driver: PAL/H, NTSC/Kr, SECAM B/G/H/LC */=
<br>
  #define CX23885_NORMS (\<br>
&lt;&lt; Leadtek.Winfast.PxDVR.3200.H.2.diff &gt;&gt;<br>
</blockquote>
</div>
<br>

--=20
<div> Be Yourself @ mail.com!<br>
Choose From 200+ Email Addresses<br>
Get a <b>Free</b> Account at <a href=3D"http://www.mail.com/Product.aspx" t=
arget=3D"_blank">www.mail.com</a>!</div>
</div></body></html>
------=_Part_0_8087063.1218023586329--



More information about the linux-dvb mailing list