[linux-dvb] irq overflow

Christian Hofrichter hofrichter at freenet.de
Mon Jun 23 15:07:23 CEST 2008


I have a problem with my dvb-t satelco easywatch mobile set (pluto2 chipset). 
When I tune 
the card to a tv channel and receive the signal I get an irq overflow . The 
overflow is followed by picture and sound 
distortions and happens in a interval of exactly 30 seconds. It is a pcmcia 
card running with kernel 2.6.25 and the pluto2 module.


-------------

cat /proc/interrupts
0:     138089  local-APIC-edge      timer
  1:          8   IO-APIC-edge      i8042
  8:          0   IO-APIC-edge      rtc
 12:        135   IO-APIC-edge      i8042
 14:      42402   IO-APIC-edge      ide0
 15:      49216   IO-APIC-edge      ide1
 17:      39835   IO-APIC-fasteoi   ATI IXP, ATI IXP Modem, fglrx[0]@PCI:1:5:0
 19:      66941   IO-APIC-fasteoi   ohci_hcd:usb1, ehci_hcd:usb2,ohci_hcd:usb3
 20:     489269   IO-APIC-fasteoi   yenta, pluto2
 21:        649   IO-APIC-fasteoi   acpi, tifm_7xx1, firewire_ohci
 22:     147830   IO-APIC-fasteoi   b43
 23:      54524   IO-APIC-fasteoi   eth0
NMI:          0   Non-maskable interrupts
LOC:    7128518   Local timer interrupts
TRM:          0   Thermal event interrupts
THR:          0   Threshold APIC interrupts
SPU:          0   Spurious interrupts
ERR:          0



-----------------

dmesg
pccard: card ejected from slot 0
pccard: CardBus card inserted into slot 0
PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:03:00.0 to 64
DVB: registering new adapter (pluto2)
pluto2 0000:03:00.0: board revision 2.15
pluto2 0000:03:00.0: S/N 13320542100301
pluto2 0000:03:00.0: MAC 00:d0:16:03:bb:9c
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 53MHz sampling clock
tda1004x: timeout waiting for DSP ready
tda1004x: found firmware revision 0 -- invalid
tda1004x: trying to boot from eeprom
tda1004x: timeout waiting for DSP ready
tda1004x: found firmware revision 0 -- invalid
tda1004x: waiting for firmware upload...
tda1004x: found firmware revision 20 -- ok
pluto2 0000:03:00.0: overflow irq (1)


-------------------



tzap -c channels.conf XXX
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
reading channels from file 'channels.conf'
..
..
..
status 00 | signal 9b9b | snr abab | ber 0001fffe | unc 00000000 |
status 1f | signal 9c9c | snr fcfc | ber 0000011a | unc ffffffff | FE_HAS_LOCK
status 1f | signal 9c9c | snr fefe | ber 0000005c | unc 00000000 | FE_HAS_LOCK
status 1f | signal 9b9b | snr fefe | ber 00000072 | unc 00000000 | FE_HAS_LOCK
status 1f | signal 9d9d | snr fefe | ber 00000078 | unc 00000000 | FE_HAS_LOCK
...
...


--------------

/var/log/messages

tda1004x: setting up plls for 53MHz sampling clock
tda1004x: timeout waiting for DSP ready
tda1004x: found firmware revision 0 -- invalid
tda1004x: trying to boot from eeprom
tda1004x: timeout waiting for DSP ready
tda1004x: found firmware revision 0 -- invalid
tda1004x: waiting for firmware upload...
tda1004x: found firmware revision 20 -- ok
pluto2 0000:03:00.0: overflow irq (1)
ta1004x: setting up plls for 53MHz sampling clock
tda1004x: found firmware revision 20 -- ok
pluto2 0000:03:00.0: overflow irq (1)
APIC error on CPU0: 40(40)
pluto2 0000:03:00.0: overflow irq (1)
pluto2 0000:03:00.0: overflow irq (1)



Note the apic error seems unrelated as booting with noapic doesn't change
anything.


-----------------

lspci -vv:
00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 64

00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00006000-00006fff
        Memory behind bridge: d0300000-d03fffff
        Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
        Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [44] HyperTransport: MSI Mapping
        Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
308b

00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal
decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
        I/O behind bridge: 00004000-00005fff
        Memory behind bridge: cc000000-cfffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
                Device: Latency L0s <64ns, L1 <1us
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
                Link: Latency L0s <64ns, L1 <1us
                Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
                Link: Speed 2.5Gb/s, Width x16
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
                Slot: Number 2, PowerLimit 10.000000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
                Slot: AttnInd Off, PwrInd Off, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000
        Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
308b
        Capabilities: [b8] HyperTransport: MSI Mapping
        Capabilities: [100] Advanced Error Reporting

00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37 (prog-if 00
[Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
        I/O behind bridge: 00002000-00003fff
        Memory behind bridge: c8000000-cbffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
                Device: Latency L0s <64ns, L1 <1us
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
                Link: Latency L0s <64ns, L1 <1us
                Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
                Link: Speed 2.5Gb/s, Width x16
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
                Slot: Number 3, PowerLimit 6.500000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
                Slot: AttnInd Off, PwrInd Off, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000
        Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
308b
        Capabilities: [b8] HyperTransport: MSI Mapping
        Capabilities: [100] Advanced Error Reporting

00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(prog-if 10 [OHCI])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at d0400000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000

00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
(prog-if 10 [OHCI])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at d0401000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000

00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
(prog-if 20 [EHCI])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at d0402000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
                Bridge: PM- B3+
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000

00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11)
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Region 0: I/O ports at 8200 [size=16]
        Region 1: Memory at d0403000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [b0] HyperTransport: MSI Mapping

00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE
Controller ATI (prog-if 8a [Master SecP PriP])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at 7010 [size=16]
        Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000

00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01
[Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
        I/O behind bridge: 00001000-00001fff
        Memory behind bridge: d0000000-d02fffff
        Prefetchable memory behind bridge: 50000000-53ffffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 
Audio
Controller (rev 02)
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Latency: 64 (500ns min), Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 17
        Region 0: Memory at d0404000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000

00:14.6 Modem: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller (rev 
02)
(prog-if 00 [Generic])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Latency: 64 (500ns min), Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 17
        Region 0: Memory at d0405000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- 
Queue=0/0
Enable-
                Address: 00000000  Data: 0000

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Capabilities: [80] HyperTransport: Host or Secondary Interface
                !!! Possibly incomplete decoding
                Command: WarmRst+ DblEnd-
                Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0
                Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
                Revision ID: 1.02

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Address
Map
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-

01:05.0 VGA compatible controller: ATI Technologies Inc ATI Radeon XPRESS 200M
5955 (PCIE) (prog-if 00 [VGA])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B+
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 255 (2000ns min), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
        Region 1: I/O ports at 6000 [size=256]
        Region 2: Memory at d0300000 (32-bit, non-prefetchable) [size=64K]
        [virtual] Expansion ROM at d0320000 [disabled] [size=128K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit
Ethernet (rev 03)
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0 (16000ns min)
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at <ignored> [disabled]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
        Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ 
Queue=0/3
Enable-
                Address: ffef3ffffffff7f8  Data: ffff

02:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g]
802.11g Wireless LAN Controller (rev 02)
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at d0010000 (32-bit, non-prefetchable) [size=8K]

02:04.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 168, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at d0012000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        Memory window 0: 50000000-53fff000 (prefetchable)
        Memory window 1: 54000000-57fff000
        I/O window 0: 00001000-000010ff
        I/O window 1: 00001400-000014ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
        16-bit legacy interface ports at 0001

02:04.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host
Controller (prog-if 10 [OHCI])
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 21
        Region 0: Memory at d0013000 (32-bit, non-prefetchable) [size=2K]
        Region 1: Memory at d0014000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+

02:04.3 Mass storage controller: Texas Instruments PCIxx21 Integrated
FlashMedia Controller
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 21
        Region 0: Memory at d0018000 (32-bit, non-prefetchable) [size=8K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:04.4 Generic system peripheral [0805]: Texas Instruments PCI6411, PCI6421,
PCI6611, PCI6621, PCI7411, PCI7421, PCI7611, PCI7621 Secure Digital (SD)
Controller
        Subsystem: Hewlett-Packard Company MX6125
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 9
        Region 0: Memory at d001a000 (32-bit, non-prefetchable) [size=256]
        Region 1: Memory at d001b000 (32-bit, non-prefetchable) [size=256]
        Region 2: Memory at d001c000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:00.0 Multimedia video controller: SCM Microsystems, Inc. Pluto2 DVB-T
Receiver for PCMCIA [EasyWatch MobilSet]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- 
<TAbort-
<MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at 54000200 (32-bit, non-prefetchable) [size=128]
        Region 1: Memory at 54000000 (32-bit, non-prefetchable) [size=512]
        Capabilities: [78] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

_______________________________________________
linux-dvb mailing list
linux-dvb at linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb



More information about the linux-dvb mailing list