How to Obtain, Build and Install V4L-DVB Device Drivers

From LinuxTVWiki

(Difference between revisions)
Jump to: navigation, search
(Build and Installation Instructions: Umm, intermediary save -- getting tired and have already forgotten what changes I've made)
(Kernel Support: screw it, looks messy. just remove crud)
Line 9: Line 9:
The LinuxTV V4L-DVB drivers will work only in conjunction with relatively modern 2.6 kernels; specifically,  
The LinuxTV V4L-DVB drivers will work only in conjunction with relatively modern 2.6 kernels; specifically,  
{{Note|CityK here:  I have no clue as to where the current backwards compatibility status stands.  Suffice to say, more modern kernels (which I'd define as ~2.6.32 and newer) are much more likely to work with the new media_build snapshots of the git tree.  I'll leave the former text of this section for now, albeit in strike-through form.  When the situation is more clear, please update this section accordingly.}}
{{Note|CityK here:  I have no clue as to where the current backwards compatibility status stands.  Suffice to say, more modern kernels (which I'd define as ~2.6.32 and newer) are much more likely to work with the new media_build snapshots of the git tree.  When the situation is more clear, please update this section accordingly.}}
<s>the V4L-DVB tree is currently backwards compatible with vanilla kernels from currently 2.6.16 onwards.
In the past, backwards compatibility meant 2.6.12 and greater, but, as time has progressed, the number of significant (and progressive!) changes introduced within the drivers have made it extremely difficult, if not impossible, to provide as thorough compatibility between the newest V4L-DVB releases and older kernels.  Consequently, as mentioned above, in order to install a recent snapshot of the V4L-DVB drivers onto your system, you will need to be utilizing a kernel 2.6.16 or greater.
If you have configured the kernel manually, please note that some capabilities should be enabled like EVDEV. You should also investigate installing the "[[Wikipedia:udev|udev]]" package (for kernels >= 2.6.15) which automatically populates the /dev directory when devices are found.  Stock kernels should have everything required.</s>
===Additional Software Requrirements===
===Additional Software Requrirements===

Revision as of 06:22, 9 January 2011

The LinuxTV project hosts the latest set of Linux kernel driver modules for V4L-DVB devices. This page contains information to help an "end user" install these device drivers in a GNU/Linux system.

Note: This article assumes that:
  • your device is actually supported by the drivers -- Just because your board happens to have a chip on it that corresponds to some existing driver does NOT mean your product is supported. The driver has to be aware that it's related to some hardware (typically through the subsystem ID from the USB ID or PCI ID). If the driver doesn't recognize/bind to your particular hardware, then the module will probably load but then proceed to not do anything. In other words, support for your device would have to be added to the driver.
  • you have already physically installed the hardware device into, or connected it to, your system. (Refer to the manufacturer's instructions for such details)


Software Requirements

Kernel Support

The LinuxTV V4L-DVB drivers will work only in conjunction with relatively modern 2.6 kernels; specifically,

Note: CityK here: I have no clue as to where the current backwards compatibility status stands. Suffice to say, more modern kernels (which I'd define as ~2.6.32 and newer) are much more likely to work with the new media_build snapshots of the git tree. When the situation is more clear, please update this section accordingly.

Additional Software Requrirements

In order to be able to build the V4L-DVB kernel driver modules, you will need:

  • kernel-source or kernel-headers
  • (OpenSuSE and fedora only) kernel-devel
  • make
  • gcc
  • git

If these packages are not currently installed on your system, you should do so now.

Retrieving the Latest V4L-DVB Source Code

After installing all required software, download a copy of the latest source code from LinuxTV. You can do that by:

git clone git://

Build and Installation Instructions

Optional Pre-Compilation Steps

These optional command steps are applicable only in certain situations approaching a new build of the driver set, or for experienced users wishing to streamline the build process to consist of only those components they want to install.

  • make rminstall ... you would use this to remove the currently installed driver set (located within the relevant /lib/modules/["kernel version"]/kernel/drivers/media directory to which they were installed)
  • make distclean ... cleans up the build configuration environment ... noteworthy is that it will set things up such that a following "make" build process will be against "/usr/src/[uname -r]” kernel source
  • make menuconfig ... this will open up the ncurses based menu that allows you to select only those components you wish to build and install

The building system offers some other make targets that may be useful for advanced users or developers. For listing the supported targets, please use make help.

Building/Compiling the Modules

Note: If you are using Ubuntu, before proceeding to build the modules, you will have to edit the file v4l/.config and change the line for the firedtv driver from "firedtv=m" to "firedtv=n". The reason for this necessity is because Ubuntu has a bug in their packaging of the kernel headers that results in a fatal compilation error within the v4l-dvb build process when it reaches the firedtv module. This is a long standing issue, and one of the most frequently reported on the mailing list. Please nag the crap out of Ubuntu package managers to fix this problem!

with the script

Manually Start by changing into the directory that contains the previously downloaded source:

cd media_build/linux

Build/compile the modules from source with the command:


This will create a /v4l directory within which the completed *.ko module files will be written. Generally, this step will tend to take a while to complete; being dependent upon both the number of modules being built and your system's processing power.

Note: For multi-core processor systems, the make command has available options that can be beneficial in terms of the reducing the amount of time required for the process' completion. Specifically, you can run "make -jN" (where "N" = 1 + the number of cores your cpu has ... i.e. if you have a dual core cpu use: make -j3 )

The build progress can be observed via the console output. Some drivers included within the snapshot may have their own requirements in regards to the kernel that you must be running in order for the module to be built; such cases can be found listed at the beginning of the build output.

The entire build process should complete without error. If any errors are encountered, the compilation will be halted and, at this point, you should not attempt to proceed any further (unless you really, really enjoy experiencing the outcome of a preordained failure). Errors that prevent building a particular V4L-DVB snapshot do indeed surface from time to time, but these are usually corrected quickly upon notification from an end user submitted bug report, or upon detection from the daily automated build tests (see note below).

Note: The Daily Automated Build Tests
Hans Verkuil has set up an automated daily build of the V4L-DVB source code upon all supported kernels, as well as testing that very same upon several CPU architectures. A brief synopsis of the results from those tests is published each day on the Linux-Media Mailing List (LMML) under a message subject heading prefix of "[cron job] v4l-dvb daily build ...". A link to more detailed results of these tests is also provided within that message or can be found directly from here.

If you do run into any problems during the build step, you should:

  • first, see whether the issue is already known or not -- consult the results of the daily automated build tests (see note above)
  • if it appears that this is a new issue, please inform the developers of the bug via the LMML (preferred) or thorough one of the irc channels (#v4l or #linuxtv or #dvb).
  • you may also wish to consult any errata that might be found on this article's talk page

In general, if the source builds correctly, it is likely that the drivers will work, though this is not a guarantee.

Installing the Modules

The next step is to install the kernel driver modules by executing:

sudo make install

The command above will prompt you for your root password, and will then copy the *.ko module files you built in the above step into the /lib/modules/[kernel version]/kernel/drivers/media directories.

Note: If your distribution doesn't support the sudo command (i.e the command line returns "bash: sudo: command not found"), use the "su" command instead. "su" will prompt you for the root password, and after which entering, you can then proceed with the command. Ex.:
make install

Note: In the case where you have more then one kernel installed but have used the pre-compilation option of "make distclean", the new modules will be installed only into the /lib/modules/[uname -r]/kernel/drivers/media directory

First Use: Out with the Old, In with the New

Before trying to use the device with your newly installed driver set, you should remove from system memory any older versions of related modules that may have been loaded by the running kernel; otherwise, you will likely run into various fatal mismatch errors -- typified by an "unknown symbol" or "unknown parameter" -- as a result of your system trying to work from a mixture of old and new modules.

To achieve a clean slate state, you could either:

1. Reboot: Perhaps the most straightforward thing to do at this point, particularly for Linux newbies, is to just restart your system; the reboot will, obviously, clear out the old modules loaded into memory and, as an added bonus, create a fresh running environment under which the new modules should have been automagically loaded into system memory.

Or, on the other hand,

2. Take care of business yourself: More experienced users might prefer to use more eloquent approaches. For example, using

sudo make unload

will essentially (and similar as to manually using "rmmod" commands) remove all older modules for the device that might be currently loaded in memory by the running kernel. After which, one can then load, from the newly installed device driver set, the appropriate modules for the device using relevant

modprobe driver_name 


For Advanced Users
The following information is likely useful only for developers. After building the modules as per usual ("make"), and without needing to install them, you can:

  • remove all older modules from memory at once using "make unload" and
  • then insert all the newly built modules into memory for the running kernel with "make load"

Alternatively, to perform the previous two commands ("make unload" and "make load") in a single step, you can use "make reload"

Note, however, that it is highly recommended that you avoid using either the make load or make reload options, as they will end up inserting all V4L-DVB device drivers into memory, and that may introduce instability, or complicate testing.

Regardless of which approach you take to remove the old modules and to insert the new ones, the end result should be the same. In addition, upon future starts of your system, your device should "automagically" be detected and will have the appropriate driver modules loaded into memory.

If the Modules load correctly:

Provided that the modules were loaded correctly into system memory:

1. They should be listed in /proc/modules: you can use either cat /proc/modules or, even better, lsmod to see this content.

Which modules should you be looking for? Well, the answer to that question depends entirely upon the chipsets used by your device -- see the relevant wiki article for your device for a listing of such components and required drivers (or search the web if such information does not exist. Note: Please add any information missing from the wiki!)

2. They should provide some indication within your system log: you can consult the output from the "dmesg" command or directly review your system log file (typically housed within the /var/log directory) for indication that they have been successfully loaded and that the device is now correctly configured for operation. Examples of successful module loads are provided by users under the "Sample kernel output" section in many device articles witin the wiki.

3. The device manager udev will "automagically" create appropriate device nodes on /dev:
(a) For a DVB device, you should now have a non-empty /dev/dvb directory. You can check on whether this is true for you with the following command:

ls -l /dev/dvb/

(alternatively, you can browse your directory structure with the graphical file manager of your choice). If you have a single DVB device installed in your system, then the output of the above command should reveal that /dev/dvb/ is populated by adapter0. Digging further,

ls -l /dev/dvb/adapter0

reveals the character devices associated with adapter0 for which the drivers have control. If you have more then one DVB device, you can see the same for all with

ls -l /dev/dvb/adapter*

(b) For a V4L device, you should now have a non-empty /dev/v4l directory. You can check on whether this is true for you with the following command:

ls -l /dev/v4l

Digging further,

ls -l /dev/v4l/by-path

reveals the symbolic links to the character devices associated with your V4L adapter for which the drivers have control. The most typical of which is /dev/video0. If you have more then one V4L device, you can see the same for all with

ls -l /dev/video*

If the Modules did not load correctly or the device is still not configured correctly for use:

There could be several reasons why you may have encountered a module loading error or, absent such an error, why the device is still not configured correctly for use, even after having correctly followed the steps from the above procedure. If either of these cases applies, the very first thing you should do is check whether your device is actually supported by the driver (see the very first note at the top of this page). Next, provided your device is supposed to be supported, check within your system log/dmesg for any messages that may give indication as to the problem. The following points address a few common trouble spots:

Module Load Order Can Matter

  • in cases where loading more then one module is necessary, the order in which you load the modules can matter!

Sometimes Automagic just isn't Automagic

  • If a module was, for whatever reason, not loaded, you can try manually loading it with the appropriate modprobe command.

Unresolved Symbols

  • if you tried the second method ("make unload" followed by an appropriate modprobe command) but encountered errors in relation to unresolved symbols, e.g. using the saa7134 module as an example:
sudo modprobe saa7134
FATAL: Error inserting saa7134 (/lib/modules/[your kernel version]/kernel/drivers/media/video/saa7134/saa7134.ko):\ 
Unknown symbol in module, or unknown parameter (see dmesg) 

please try a system reboot before filing an error report. Irregardless of what caused the unresolved symbols errors, usually, after performing the reboot, you will find that the install was actually successful and the drivers will work as intended.

  • Special case: If your system uses compressed kernel modules, after running the "make install" command of the V4L-DVB installation process, you could end up with a mixture of new modules (*.ko) and their older compressed version (*.ko.gz) installed. If the system attempts to concurrently load both sets into memory, you are bound to run into modprobe insertion errors (eg. unknown symbol or unknown parameter). All conflicting *.ko.gz files must be removed. The following command line can help you locate these conflicting files in all your installed kernels:
for file in `find /lib/modules -name "*.ko"`; do if [[ -e $file.gz ]]; then echo "$file.gz should be removed"; fi; done

Usually all conflicting module files resulting of v4l-dvb installation will be located in:

/lib/modules/[your kernel version]/kernel/drivers/media

Once the conflicting *.ko.gz have been moved elsewhere or renamed (to *.ko.gz.disabled for example), use the v4l-dvb reload command and, to be safe, also add a "depmod" step in order to rebuild modules dependencies):

make reload
depmod -a

Your new modules should now be loaded correctly.

A Note on Firmware

  • You have all the modules active (listed in lsmod) but device nodes are nowhere to be found: The problem may be as simple as the firmware for the device not being loaded; some devices also require a firmware, which is uploaded from the host PC to the device, in order to operate.

In some cases, when the device is correctly recognized, the associated drivers provide information as to which firmware file is required -- look in the system log output. For example, for many TechnoTrend & Hauppauge (and other similar "premium" cards), if the dvb-ttpci firmware is not available you will observe an error such as:

  dvb-ttpci: could not load firmware, file not found: dvb-ttpci-01.fw
  dvb-ttpci: usually this should be in /usr/lib/hotplug/firmware or /lib/firmware
  dvb-ttpci: and can be downloaded from

Resolving that missing firmware issue should then result in proper detection and configuration of your device. In other cases, obtaining the correct firmware is not so straightforward a task. The very first thing you need to know is what device you're using; see "Determining the Device's Identity". Once you have established which particular device you are in possession of, you can then move on to obtaining the correct firmware. In addition, information in wiki articles (eg. such as DVB-T USB Devices) will cite the appropriate firmware required. If you're still at a loss, a Google search may shed light on what file you need. Note, however, that not all supported devices have easily available firmware (eg. Hauppauge HVR 1100 & 1300). Firmware for such cards could be loaded via temporary installation in a Mirosoft Windows System with the manufacturer-supplied drivers.

In any regard, once you find and obtain the necessary firmware for your device, copy it into the appropriate directory; the directory location depends upon that used by your distro, but typically it is:

  • /lib/firmware

Consult resources for your distro if its preferred location is somewhere otherwise.

Some Further Documentation

Personal tools