[linux-dvb] problems with Hauppauge DVB/S finding a stream

[jhall@UU.NET (Jeremy Hall)]

Hello,

I have a Hauppauge DVB/S and am having trouble getting it to see any
satellite signals.  When inserting the module, it looks like this:

Rainbow:/var/log # modprobe dvb
May 14 19:39:18 Rainbow kernel: i2c-core.o: driver i2c TV tuner driver
registered.
May 14 19:39:18 Rainbow kernel: i2c-core.o: driver stv0299 DVB demodulator
registered.
May 14 19:39:18 Rainbow kernel: i2c-core.o: driver L64781 DVB demodulator
registered.
May 14 19:39:18 Rainbow kernel: i2c-core.o: driver VES1820 DVB demodulator
registered.
May 14 19:39:18 Rainbow kernel: i2c-core.o: driver VES1893 DVB demodulator
registered.
May 14 19:39:18 Rainbow kernel: PCI: Found IRQ 11 for device 00:0f.0
May 14 19:39:18 Rainbow kernel: PCI: Sharing IRQ 11 with 00:02.2
May 14 19:39:18 Rainbow kernel: saa7146_core.o: saa7146(1): bus:0, rev:1,
mem:0xe1840e00.
May 14 19:39:18 Rainbow kernel: i2c-dev.o: Registered 'saa7146(1)' as
minor 0
May 14 19:39:18 Rainbow kernel: tuner: ignoring saa7146(1) i2c adapter
[id=0x60000]
May 14 19:39:18 Rainbow kernel: i2c-core.o: client [stv0299] registered to
adapter [saa7146(1)](pos. 0).
May 14 19:39:18 Rainbow kernel: i2c-core.o: adapter saa7146(1) registered
as adapter 0.
Rainbow:/var/log # May 14 19:39:19 Rainbow kernel: dvb0: AV7110 - firm
f053e1cd, rtsl 77cee1ce, vid 3e90d49d, app 00000000
May 14 19:39:20 Rainbow kernel: dvb: 1 dvb(s) found!

I have options dvb init_chan=2 and pids_off=0 for the dvb module.

WHat looks odd is that at first it says it is ignoring an I2C
tuner. (could this be my problem?)
/proc/video/dev/video0 is:

Rainbow:/proc/video/dev # cat video0
name            : DVB Board
type
: VID_TYPE_CAPTURE|VID_TYPE_TUNER|VID_TYPE_OVERLAY|VID_TYPE_CLIPPING|VID_TYPE_FRAMERAM|VID_TYPE_SCALES
hardware        : 0xb
Rainbow:/proc/video/dev #

When I try to tune a channel with szap, it appears everything is going
fine with the exception that szap outputs tuning failed after waiting
about 3 seconds.

The Dish Network LNB appears to use a high lof of 11.25ghz, so I adjusted
that as well as the switching frequency.  Since the SW-64 is not a 2way
switch, , I cannot get responses from it--documentation I have read
suggests that changes in voltage received should indicate failure or
acceptance of whatever I tried to do, but I can't tell what the deal is.

I am using kernel 2.4.19-pre7 with LL patches and have i2c and videodev in
the kernel, not modules.

The DVB card outputs a PAL video signal, no audio.

Help is greatly appreciated.

_J


-- 
Info:
To unsubscribe send a mail to listar@linuxtv.org with "unsubscribe linux-dvb" as subject.