[linux-dvb] 5 months and counting...

To: linux-dvb@linuxtv.org
Subject: [linux-dvb] 5 months and counting...
From: raid517 <raid517@fairadsl.co.uk>
Date: Mon, 11 Oct 2004 01:41:23 +0100
Content-type: text/plain; charset=us-ascii; format=flowed
List-help: <mailto:ecartis@linuxtv.org?subject=help>
List-id: linux-dvb <linux-dvb.mail>
List-owner: <mailto:listmaster@convergence.de>
List-post: <mailto:linux-dvb@linuxtv.org>
List-software: Ecartis version 1.0.0
List-subscribe: <mailto:ecartis@linuxtv.org?subject=subscribe%20linux-dvb>
List-unsubscribe: <mailto:ecartis@linuxtv.org?subject=unsubscribe%20linux-dvb>
Sender: linux-dvb-bounce@linuxtv.org
User-agent: Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.7.2) Gecko/20040819 Debian/1.7.2-3

Well maybe this is a record, but I have been trying on ond off for about 5 months now to get my TV card working in Linux.

In that time I have tried maybe 8 different distros (although I am now settled on Debian with no intention of switching).

I think unless any of you guys have any more suggestions it may be time to give up.

Everything seems as it should be. I have a winTV nova-t card, the drivers and (as far as I can tell) the firmware is loaded, the script MAKEDEV-DVB.sh to create the correct devices in /dev/dvb ran without a glitch, lspci and modprobe lists my drivers and card type as being in agreement, cat /proc/devices gives 212 DVB as my major DVB device number - everything *seems* to be singing in harmony. Yet when I run the command ./scan dvb-t/uk-Fenham I just get the same old output I have always got:

./scan dvb-t/uk-Fenham
scanning dvb-t/uk-Fenham
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:1882: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 19 No such device

The same is true if I try to run any of the other included utilities. It just seems that any Linux version I have installed on this machine (Abit Nforce 2.0 Rev: 2) does not regard and devices created using the MAKEDEV-DVB.sh script as 'real' devices. I have changed the permission on all of these devices to read, write and execute.

So I will take this one last stab to see if any of you guys can see where I might have missed something - or where I might be going wrong.

I will print the list of common commands I have run to check whether things are as they should be. I am sorry for the potential information overload - but these are questions I am likely to be asked anyway.

If you have the stamina to read this and solve what now seems like an unsolvable puzzle, your input would be appreciated.

But after this I have no option but to forget it for good.

Thanks in advance for looking.

GJ

raid517@4[~]$ lspci
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1)
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3)
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
0000:01:08.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04)
0000:01:08.1 Input device controller: Creative Labs SB Audigy MIDI/Game port (rev 04)
0000:01:08.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04)
0000:01:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
0000:02:00.0 VGA compatible controller: ATI Technologies Inc RV350 NJ [Radeon 9800 XT]
0000:02:00.1 Display controller: ATI Technologies Inc RV350 NJ [Radeon 9800 XT] (Secondary)
raid517@4[~]$ cat /proc/devices
Character devices:
1 mem
2 pty
3 ttyp
4 /dev/vc/0
4 tty
4 ttyS
5 /dev/tty
5 /dev/console
5 /dev/ptmx
6 lp
7 vcs
10 misc
13 input
14 sound
21 sg
29 fb
81 video4linux
116 alsa
119 vmnet
128 ptm
136 pts
171 ieee1394
180 usb
212 DVB
254 pcmcia

Block devices:
1 ramdisk
2 fd
3 ide0
7 loop
8 sd
11 sr
22 ide1
62 cdemu
65 sd
66 sd
67 sd
68 sd
69 sd
70 sd
71 sd
128 sd
129 sd
130 sd
131 sd
132 sd
133 sd
134 sd
135 sd
raid517@4[~]$ lsmod
Module Size Used by
ipv6 262660 6
vmnet 30736 12
vmmon 48056 0
parport_pc 40256 0
lp 11692 0
parport 41800 2 parport_pc,lp
saa7146_vv 50688 0
video_buf 22148 1 saa7146_vv
v4l1_compat 14596 1 saa7146_vv
v4l2_common 6400 1 saa7146_vv
videodev 9984 1 saa7146_vv
tda1004x 18824 0
evdev 9600 0
sg 34592 0
ds 19076 0
yenta_socket 21760 0
pcmcia_core 66756 2 ds,yenta_socket
8250 21088 0
serial_core 23808 1 8250
eth1394 22024 0
hfsplus 60164 0
hfs 47492 0
minix 33156 0
nls_iso8859_1 4352 2
ntfs 99668 2
sbp2 24584 0
ohci1394 35844 0
ieee1394 111288 3 eth1394,sbp2,ohci1394
snd_emu10k1 98568 0
snd_rawmidi 25636 1 snd_emu10k1
snd_pcm_oss 54568 0
snd_mixer_oss 20096 1 snd_pcm_oss
snd_pcm 97800 2 snd_emu10k1,snd_pcm_oss
snd_timer 25732 1 snd_pcm
snd_seq_device 8456 2 snd_emu10k1,snd_rawmidi
snd_ac97_codec 69764 1 snd_emu10k1
snd_page_alloc 11912 2 snd_emu10k1,snd_pcm
snd_util_mem 4864 1 snd_emu10k1
snd_hwdep 9732 1 snd_emu10k1
snd 56932 10 snd_emu10k1,snd_rawmidi,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_seq_device,snd_ac97_codec,snd_util_mem,snd_hwdep
soundcore 10208 1 snd
forcedeth 17792 0
budget 6784 0
budget_core 8836 1 budget
dvb_core 87848 3 tda1004x,budget,budget_core
saa7146 19364 3 saa7146_vv,budget,budget_core
ttpci_eeprom 3072 1 budget_core
loop 16136 0
cdemu 11404 0
thermal 13072 0
processor 13220 1 thermal
fan 4236 0
button 6552 0
battery 9740 0
ac 5132 0
floppy 58960 0
uhci_hcd 33040 0
ohci_hcd 21636 0
raid517@4[~]$ dmesg
14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APCE] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbf00
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbf30, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 4
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 4 (level, low) -> IRQ 4
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5
ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
ACPI: PCI interrupt 0000:01:08.2[B] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 10 (level, low) -> IRQ 10
vesafb: framebuffer at 0xd0000000, mapped to 0xe0808000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:57b3
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Total HugeTLB memory allocated, 0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Console: switching to colour frame buffer device 128x48
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 256M @ 0xc0000000
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y200P0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 398297088 sectors (203928 MB) w/7936KiB Cache, CHS=24792/255/63, UDMA(133)
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.02 loaded.
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 3 (level, low) -> IRQ 3
ehci_hcd 0000:00:02.2: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 3, pci mem e0b8b000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 15
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S1 S4 S5)
RAMDISK: Couldn't find valid RAM disk image starting at 0.
ReiserFS: hda4: found reiserfs format "3.6" with standard journal
usb 1-1: new high speed USB device using address 2
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Revoltec Model: USB/IDE Bridge ( Rev: 0103
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
sda: sda1
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
USB Mass Storage device found at 2
ReiserFS: hda4: using ordered data mode
ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda4: checking transaction log (hda4)
ReiserFS: hda4: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 164k freed
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:02.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 11, pci mem e0c3c000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 4 (level, low) -> IRQ 4
ohci_hcd 0000:00:02.1: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 4, pci mem e0c3e000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v2.2
inserting floppy driver for 2.6.8.1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (41 C)
Adding 996020k swap on /dev/hda2. Priority:1 extents:1
cdemu:939: ver 0.6.0 loaded. Registered 8 cdemus.
loop: loaded (max 8 devices)
saa7146: register extension 'budget dvb'.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.28.
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 0147b:1c00 bound to 0000:00:04.0
ACPI: PCI interrupt 0000:01:08.0[A] -> GSI 5 (level, low) -> IRQ 5
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:01:08.2[B] -> GSI 7 (level, low) -> IRQ 7
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[7] MMIO=[e3006000-e30067ff] Max Packet=[2048]
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
NTFS driver 2.1.15 [Flags: R/O MODULE].
NTFS volume version 3.1.
VFS: Can't find ext3 filesystem on dev hda3.
VFS: Can't find ext2 filesystem on dev hda3.
Unable to identify CD-ROM format.
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c01010072f5]
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
NTFS volume version 3.1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0: LSR safety check engaged!
ttyS0: LSR safety check engaged!
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
NTFS volume version 3.1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
NTFS volume version 3.1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
Linux video capture interface: v1.00
lp: driver loaded but no devices found
ttyS0: LSR safety check engaged!
ttyS1: LSR safety check engaged!
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
/dev/vmnet: open called by PID 2159 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 2171 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2276 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2277 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 2327 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2291 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03b1f60(lo)
IPv6 over IPv4 tunneling driver
vmnet8: no IPv6 routers present
vmnet1: no IPv6 routers present
eth0: no IPv6 routers present
NTFS volume version 3.1.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set iso8859-1.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set iso8859-1.
SCSI error: host 0 id 0 lun 0 return code = 8000002
Sense class 7, sense error 0, extended sense 0
NTFS volume version 3.1.

Not sure what all the SCSI errors are here. I'm running Kernel 2.6.8.1 and don't have any SCSI devices installed. I have a usb 2.0 harddrive - but I don't think that's relevant to this issue. I have all the DVB kernel modules enabled and loaded as modules, rather than compiled into the kernel.

I have no clue where to go from here.

GJ

Follow-Ups:
- [linux-dvb] Re: 5 months and counting...
  - From: Andrew de Quincey <adq_dvb@lidskialf.net>
- [linux-dvb] Re: 5 months and counting...
  - From: Torgeir Veimo <torgeir@pobox.com>

Prev by Date: [linux-dvb] Re: video pts differences on dvb-t in the uk
Next by Date: [linux-dvb] Re: refactoring
Previous by thread: [linux-dvb] Weird non existant modules?
Next by thread: [linux-dvb] Re: 5 months and counting...
Index(es):
- Date
- Thread

Home | Main Index | Thread Index