[linux-dvb] DVB-T premium installation on SuSE 9.2

[Tomas =?utf-8?q?S=C3=A4venstedt?= <tomas@ladata.se>]

Hello

I have been running my card under kernel 2.4 in SuSE 8.1 and it's been working OK together with VDR in the Swedish Terrestial Net.

Now when I upgraded my computer to SuSE 9.2 (kernel 2.6.8), 
I don't get any contact with the card anymore. 
I have copied the firmware flie SC_main.mc to /usr/lib/hotplug/firmware/dvb-fe-tdlb7-2.16.fw. 
The driver load as follows:

Dec 16 19:55:35 video kernel: saa7146: register extension 'dvb'.
Dec 16 19:55:35 video kernel: ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 5 (level, low) -> IRQ 5
Dec 16 19:55:35 video kernel: saa7146: found saa7146 @ mem e0f24000 (revision 1, irq 5) (0x13c2,0x0001).
Dec 16 19:55:35 video kernel: DVB: registering new adapter (Technotrend/Hauppauge PCI rev1.3 or 1.6).
Dec 16 19:55:35 video kernel: adapter has MAC addr = 00:d0:5c:01:5d:02
Dec 16 19:55:35 video kernel: gpioirq unknown type=0 len=0
Dec 16 19:55:35 video kernel: DVB: AV7111(0) - firm f0240009, rtsl b0250018, vid 71010068, app 8000261c
Dec 16 19:55:35 video kernel: DVB: AV7111(0) - firmware supports CI link layer interface
Dec 16 19:55:35 video kernel: av7110(0): Crystal audio DAC detected
Dec 16 19:55:35 video kernel: saa7146_vv: saa7146 (0): registered device video0 [v4l2]
Dec 16 19:55:35 video kernel: av7110: found av7110-0.
Dec 16 19:55:35 video kernel: evdev_connect: evdev dd327780 handle dd32779c name event3
Dec 16 19:55:36 video kernel: tdlb7: waiting for firmware upload...
Dec 16 19:55:36 video kernel: DVB: registering frontend 0 (Alps TDLB7)...
Dec 16 19:55:37 video kernel: cx22702: Detected Hauppauge Nova-T DVB-T - PLL Thomson DTT759x
Dec 16 19:55:37 video kernel: cx22702_validate_eeprom eeprom content is not valid
Dec 16 19:55:37 video kernel: drivers/media/dvb/frontends/dib3000mb.c: did not found a DiBCom 3000-MB.
Dec 16 19:55:37 video kernel: bt878 find by dvb adap: checking "Technotrend/Hauppauge PCI rev1.3 or 1.6"
Dec 16 19:55:37 video kernel: bt878 find by dvb adap: NOT found "Technotrend/Hauppauge PCI rev1.3 or 1.6"
Dec 16 19:55:37 video kernel: mt312_read: ret == -121

When I start VDR it does't tune to the selected station anymore (free or not):

Dec 16 19:23:54 video vdr[6631]: VDR version 1.2.6 started
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/setup.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/sources.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/diseqc.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/channels.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/svdrphosts.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/ca.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/remote.conf
Dec 16 19:23:54 video vdr[6631]: loading /etc/vdr/keymacros.conf
Dec 16 19:23:54 video vdr[6631]: probing /dev/dvb/adapter0/frontend0
Dec 16 19:23:54 video vdr[6631]: SectionsScanner processing thread started (pid=6631)
Dec 16 19:23:54 video vdr[6631]: probing /dev/dvb/adapter1/frontend0
Dec 16 19:23:54 video vdr[6631]: found 1 video device
Dec 16 19:23:54 video vdr[6631]: setting primary device to 1
Dec 16 19:23:54 video vdr[6631]: SVDRP listening on port 2001
Dec 16 19:23:54 video vdr[6631]: remote control LIRC - keys known
Dec 16 19:23:54 video vdr[6631]: remote control KBD - keys known
Dec 16 19:23:54 video vdr[6631]: switching to channel 1
Dec 16 19:23:54 video vdr[6631]: tuner thread started on device 1 (pid=6631)
Dec 16 19:23:54 video vdr[6631]: LIRC remote control thread started (pid=6631)
Dec 16 19:23:54 video vdr[6631]: KBD remote control thread started (pid=6631)
Dec 16 19:23:56 video vdr[6631]: reading EPG data from /var/spool/video/epg.data
Dec 16 19:24:01 video vdr[6631]: switching to channel 2

I can use the OSD and replay recording, so MPEG works OK.

I have also tried dvbscan with the same negative result.

I tried to only load the alps_tdbl7 frontend (and not all the others) but no better.
Does anybody have a clue?

Tomas