Compro VideoMate E900/E850F

lspci -vvnn:

I will clean up the format when i workout how

02:00.0 Multimedia controller [0480]: Philips Semiconductors Device [1131:7164] (rev 81)

Subsystem: Compro Technology, Inc. Device [185b:e900] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at fb000000 (64-bit, non-prefetchable) [size=4M] Capabilities: [40] MSI: Enable- Count=1/16 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [50] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x2, ASPM L0s L1, Latency L0 <4us, L1 <64us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [74] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [7c] Vendor Specific Information: Len=84 <?> Capabilities: [100 v1] Vendor Specific Information: ID=0000 Rev=0 Len=060 <?> Capabilities: [160 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Kernel driver in use: saa7164 Kernel modules: saa7164

`lshw` gives:

          *-multimedia
               description: Multimedia controller
               product: Philips Semiconductors
               vendor: Philips Semiconductors
               physical id: 0
               bus info: pci@0000:02:00.0
               version: 81
               width: 64 bits
               clock: 33MHz
               capabilities: msi pciexpress pm bus_master cap_list
               configuration: driver=saa7164 latency=0
               resources: irq:16 memory:fb400000-fb7fffff memory:fb000000-fb3fffff

Boot Messages:

saa7164[0]/0: found at 0000:02:00.0, rev: 129, irq: 16, latency: 0, mmio: 0xfb400000 saa7164_initdev() Unsupported board detected, registering without firmware saa7164 driver loaded saa7164 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 saa7164[0]: Your board isn't known (yet) to the driver. saa7164[0]: Try to pick one of the existing card configs via saa7164[0]: card=<n> insmod option. Updating to the latest saa7164[0]: version might help as well. saa7164[0]: Here are valid choices for the card=<n> insmod option: saa7164[0]: card=0 -> Unknown saa7164[0]: card=1 -> Generic Rev2 saa7164[0]: card=2 -> Generic Rev3 saa7164[0]: card=3 -> Hauppauge WinTV-HVR2250 saa7164[0]: card=4 -> Hauppauge WinTV-HVR2200 saa7164[0]: card=5 -> Hauppauge WinTV-HVR2200 saa7164[0]: card=6 -> Hauppauge WinTV-HVR2200 saa7164[0]: card=7 -> Hauppauge WinTV-HVR2250 saa7164[0]: card=8 -> Hauppauge WinTV-HVR2250 CORE saa7164[0]: subsystem: 185b:e900, board: Unknown [card=0,autodetected] saa7164[0]/0: found at 0000:02:00.0, rev: 129, irq: 16, latency: 0, mmio: 0xfb400000 saa7164_initdev() Unsupported board detected, registering without firmware