Memory Mod: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
m (link->vdrwiki)
m (minor edits)
 
(13 intermediate revisions by 4 users not shown)
Line 1: Line 1:
'''Memory Mod''' refers to upgrading a, so called, "[[Full-featured Card|full-featured]]" DVB card equipped with 2MByte SDRAM to 4MByte of SDRAM by means of placing another memory chip over an existing chip. The idea for this modification was introduced by [http://escape-edv.de/endriss/dvb-mem-mod/index.html Oliver Endriss].
==Introduction==
The idea to this modification was introduced by [http://endriss.escape.bei.t-online.de/dvb-mem-mod/index.html Oliver Endriss].


==The Idea==
==The Idea==
Full-featured DVB cards are equipped a 2 MByte SDRAM chip. Using the Linux DVB driver, OSD memory space is limited to approx. 80 KByte. Therefore, it is not possible to have a full-screen, 256 color OSD with VDR. But the AV7110/7111 is able to handle two of these chips allowing the full-screen 256 color OSD. Additional there would be more space for the video buffers. Why not add the second one?
"[[Full-featured Card|Full-featured]]" DVB cards are equipped with a 2 MByte SDRAM chip. Using the Linux DVB drivers, OSD memory space is limited to approx. 80 KBytes. Therefore, it is not possible to have a full-screen, 256 color OSD when using [[VDR]]. However, the onboard [[TI AV711x|AV7110/7111]] [[MPEG-2 Decoder]] used by these cards is able to handle/address two 2MByte SDRAM chips. Doubling the amount of addressable memory onboard these cards would effectively resolve the limitation outlined above and, hence, users could gain a full-screen 256 color OSD in VDR. Additionally there would be more space for the video buffers. Given the obvious benefit, why not add the second one?


==The Modification==
==The Modification==
[[Image:Memory_Mod_Pic1.jpg|thumb|right|Fig.1. The AV7110 and SDRAM chips before modification]]
The chip select for the second SDRAM chip is not available on the pcb itself, so the processor AV7110 and the memory chip have to be modified.
The chip select for the second SDRAM chip is not available on the card's pcb itself, so the [[TI AV711x|AV7110]] processor and the memory chip have to be modified.
{| border=0 cellpadding=2 cellspacing=0

|[[Image:Memory_Mod_Pic1.jpg|thumb|none|AV7110 and SDRAM chip before modification]]
In Fig.1 at the side of the page, you can see both chips as they are found on the card prior to any modification; with the [[TI AV711x|AV7110]] processor on the left and the, completely visible, 2MByte SDRAM memory chip on the right. The area conveyed in the image is roughly equivalent to that of the face of a 1EURO coin.
|}

Here you can see both chips before the modification.
The modification process is outlined as follows:
On the left hand side the processor, the complete visible chip is the SDRAM memory chip. As a size comparison you see a 1EURO coin.
For the Mod you have to scratch one of the thin lines on the processor until the protective coating is removed and solder a thin wire on it.
Then a second SDRAM chip has to be soldered on top of the existing one. For this you have to ''carefully'' bend the pins. Connect all pins 1:1 to the first SDRAM, except pin 18 (/ChipSelect).
This pin 18 has to be connected to the thin wire of the processor.
With an extended [[Firmware]] the processor can use the full 4Mbyte.


{{Box Warning|
{{Box Warning|
This modification is for experienced people only having knowledge and experience of SMD parts. It has to be dealed with structures around 1/10 mm. Any failure may be risky for your DVB card!
This modification is only for experienced people having knowledge and experience with SMD parts. It involves work upon intricate structures around 1/10 mm in size. Any failures with handling these parts or damage to the nearby surfaces of the card may be risky for its overall health!


'''We take no responsibility for your card!'''
'''If you undertake this modification, we take no responsibility for any damage caused or which may be incurred to your card through the process. You proceed entirely at your own risk'''
}}
}}



Image of the modified DVB board:
{{Note|It is also highly recommended that you review the [http://escape-edv.de/endriss/dvb-mem-mod/index.html information provided by Oliver] before proceeding}}
{| border=0 cellpadding=2 cellspacing=0

|[[Image:Memory_Mod_Pic2.jpg|thumb|none|AV7110 and SDRAM chip after modification]]

|}
[[Image:Memory_Mod_Pic2.jpg|thumb|right|Fig.2. The AV7110 and SDRAM chips after the completed modifications to the board]]
*Step1: carefully bend the pins of the new sdram chip, i.e. by pressing the chip on a surface. You have to bend all pins except pin 18 CS (the 8th pin of the bottom lne, starting from the right). Have a look at the picture.

*Step2: solder the second SDRAM chip onto the top of the existing one. Solder the pins of the new chip on the pins of the old one. Ensure that you have all pins connected and no short circuits.
*'''Step1''': By gently pressing on the surface of the new/second SDRAM chip that you are adding to the board, ''carefully'' bend its pins such that they all, except for pin 18, can be made to connect 1:1 to first SDRAM chip's pins. Pin 18, which is the /ChipSelect and is the 8th pin of the bottom line, starting from the right, will instead be connected to a thin wire soldered to the processor (see steps 4 and 5 of the modification process). To get a better idea of what this should look like, have a look at Fig.2
*Step3: carefully scratch through the protective coating of the AV7110 to get the coating removed from the wire. As you can see at the picture there are 6 round areas, the wire beneath the sixth with the small step is the one we need. Please do not scratch deeply as it would make it impossible to solder on that line. If you see the copper shining it's enough.

*Step4: soldering ot the line
*'''Step2''': Attach the second SDRAM chip onto the top of the existing one by soldering all the pins of the new chip (with the exception of pin 18) to the pins of the old one. Ensure that you have successfully connected the pins and that there are no short circuits.
*Step5: Connect it to the pin 18 of the sdram. Use a very thin wire of approx 0.1mm diameter.

*Step6: Fix the thin wire and check the connection again
*'''Step3''': You will have to ''carefully'' scratch through the protective coating of the [[TI AV711x|AV7110]] until the protective coating is removed and a thin trace wire/line to the processor is exposed. Looking at the image in Fig.2, you will see that there are 6 round areas, the wire beneath the sixth with the small step is the one we need. Do not scratch too deeply - if you see the copper shining, then that is enough/sufficient. If you scratch too deep, it will become impossible to solder onto that trace line, as is required in next step.

*'''Step4''': Using a very thin wire of approx 0.1mm diameter, solder the wire to the processor's trace line that you have just exposed in Step 3.

*'''Step5''': Connect/Solder the other end of the thin wire to pin 18 of the new SDRAM chip.

*'''Step6''': Fix the thin wire and check the connection again

After these steps, a completed modification should look similar to the results shown in Fig.2. If all went well, and provided that a [[Firmware]] cognizant of the additional memory is made available to the card during system boot/startup, the processor should be able to use the full 4Mbytes now residing onboard the card.


==List of suitable SDRAM chips==
==List of suitable SDRAM chips==
This list may be imcomplete.
This list may be imcomplete.
The AV711x needs 3.3Volt IO-Ports, therefore a 3.3Volt SDRAM in TSOPII packaging is needed.
The [[TI AV711x|AV71x]] needs 3.3Volt IO-Ports, therefore a 3.3Volt SDRAM in TSOPII packaging is needed.
Some of that chips are on old graphics boards.
Some of that chips are on old graphics boards.
{| cellpadding=3
{| cellpadding=3
Line 60: Line 64:


==Software Requirements==
==Software Requirements==
DVB driver with 4MB support ([[Firmware]] 261c or newer)
DVB driver with 4MB support and [[Firmware]] 261c or newer.


==Links==
==External Links==
{|
{|
| [1]
| [1]
Line 84: Line 88:
| DVB Card Upgrade 2MB->4MB (~45 Euro) bzw. SDRAM (5,00+9,70)Euro
| DVB Card Upgrade 2MB->4MB (~45 Euro) bzw. SDRAM (5,00+9,70)Euro
|}
|}

[[Category:Development]]

Latest revision as of 15:53, 10 January 2008

Memory Mod refers to upgrading a, so called, "full-featured" DVB card equipped with 2MByte SDRAM to 4MByte of SDRAM by means of placing another memory chip over an existing chip. The idea for this modification was introduced by Oliver Endriss.

The Idea

"Full-featured" DVB cards are equipped with a 2 MByte SDRAM chip. Using the Linux DVB drivers, OSD memory space is limited to approx. 80 KBytes. Therefore, it is not possible to have a full-screen, 256 color OSD when using VDR. However, the onboard AV7110/7111 MPEG-2 Decoder used by these cards is able to handle/address two 2MByte SDRAM chips. Doubling the amount of addressable memory onboard these cards would effectively resolve the limitation outlined above and, hence, users could gain a full-screen 256 color OSD in VDR. Additionally there would be more space for the video buffers. Given the obvious benefit, why not add the second one?

The Modification

Fig.1. The AV7110 and SDRAM chips before modification

The chip select for the second SDRAM chip is not available on the card's pcb itself, so the AV7110 processor and the memory chip have to be modified.

In Fig.1 at the side of the page, you can see both chips as they are found on the card prior to any modification; with the AV7110 processor on the left and the, completely visible, 2MByte SDRAM memory chip on the right. The area conveyed in the image is roughly equivalent to that of the face of a 1EURO coin.

The modification process is outlined as follows:

Warning !!!

align=left

This modification is only for experienced people having knowledge and experience with SMD parts. It involves work upon intricate structures around 1/10 mm in size. Any failures with handling these parts or damage to the nearby surfaces of the card may be risky for its overall health!

If you undertake this modification, we take no responsibility for any damage caused or which may be incurred to your card through the process. You proceed entirely at your own risk


Note: It is also highly recommended that you review the information provided by Oliver before proceeding


Fig.2. The AV7110 and SDRAM chips after the completed modifications to the board
  • Step1: By gently pressing on the surface of the new/second SDRAM chip that you are adding to the board, carefully bend its pins such that they all, except for pin 18, can be made to connect 1:1 to first SDRAM chip's pins. Pin 18, which is the /ChipSelect and is the 8th pin of the bottom line, starting from the right, will instead be connected to a thin wire soldered to the processor (see steps 4 and 5 of the modification process). To get a better idea of what this should look like, have a look at Fig.2
  • Step2: Attach the second SDRAM chip onto the top of the existing one by soldering all the pins of the new chip (with the exception of pin 18) to the pins of the old one. Ensure that you have successfully connected the pins and that there are no short circuits.
  • Step3: You will have to carefully scratch through the protective coating of the AV7110 until the protective coating is removed and a thin trace wire/line to the processor is exposed. Looking at the image in Fig.2, you will see that there are 6 round areas, the wire beneath the sixth with the small step is the one we need. Do not scratch too deeply - if you see the copper shining, then that is enough/sufficient. If you scratch too deep, it will become impossible to solder onto that trace line, as is required in next step.
  • Step4: Using a very thin wire of approx 0.1mm diameter, solder the wire to the processor's trace line that you have just exposed in Step 3.
  • Step5: Connect/Solder the other end of the thin wire to pin 18 of the new SDRAM chip.
  • Step6: Fix the thin wire and check the connection again

After these steps, a completed modification should look similar to the results shown in Fig.2. If all went well, and provided that a Firmware cognizant of the additional memory is made available to the card during system boot/startup, the processor should be able to use the full 4Mbytes now residing onboard the card.

List of suitable SDRAM chips

This list may be imcomplete. The AV71x needs 3.3Volt IO-Ports, therefore a 3.3Volt SDRAM in TSOPII packaging is needed. Some of that chips are on old graphics boards.

Producer Part Name Informations
ESMT/EliteMT M12L16161A-7T homepage datasheet
EtronTech EM636165TS-8 homepage datasheet
Samsung K4S161622E-TC80 homepage datasheet
Goldstar GM72V161621

Software Requirements

DVB driver with 4MB support and Firmware 261c or newer.

External Links

[1] vdrwiki:osdtest256-plugin Plugin for testing of modded cards
[2] vdrwiki:text2skin-plugin plugin for loading of skins
[3] http://www.rightchoiceelectronics.com/cr.html Reference list with different ICs. Needed: 1Mx16 SDRAMs.
[4] http://www.pcstats.com/ramfinder.cfm RamFinder - Infos about RAM-ICs
[5] http://www.wolfsoft.de DVB Card Upgrade 2MB->4MB (~45 Euro) bzw. SDRAM (5,00+9,70)Euro